Advertisement
Advertisement
Table of Contents
Related Manuals for Lincoln Electric SPEEDTEC 405S
Summary of Contents for Lincoln Electric SPEEDTEC 405S
- Page 1 IM3048 12/2013 REV03 SPEEDTEC 405S, 405SP, 505S & 505SP OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Declaration Of Conformity
2006/95/CEE, 2004/108/CEE and has been designed in compliance with the following standards: EN 60974-1, EN 60974-10:2007 31.05.2013 Paweł Lipiński Operations Director Lincoln Electric Bester Sp. z o.o., ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland 12/05 English English... -
Page 3: Table Of Contents
12/05 THANKS! For having choosen the QUALITY of the Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code &... -
Page 4: Technical Specifications
Technical Specifications NAME INDEX SPEEDTEC 405S K14117-1 SPEEDTEC 405SP K14117-2 SPEEDTEC 505S K14116-1 SPEEDTEC 505SP K14116-2 INPUT Input Voltage U EMC Class Frequency 405S, 405SP 400V ± 10% 50/60Hz 3-phase 505S, 505SP Input Power at Rated Cycle Input Amperes I... -
Page 5: Electromagnetic Compatibility (Emc)
If any electromagnetic disturbances are detected the operator must put in place corrective actions to eliminate these disturbances with, if necessary, assistance from Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 6: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. -
Page 7: Intoduction
Recommended equipment, which can be bought by GTAW (arc ignition using lift TIG). user, was mentioned in the chapter "Accessories". SPEEDTEC 405S, 405SP, 505S and 505SP work with the water cooler COOLARC 46. Installation and Operator Instructions operate the machine at rated welding current. -
Page 8: Output Connections
Blinking Green input source. SPEEDTEC 405S, 405SP, 505S and Normal for first 1-10 seconds after 505SP can only be connected to a mating grounded power is turned on, or if the system receptacle. -
Page 9: User Interface
(see "Accessories" chapter, Source/wire feeder cable K10349-PG-xM or K10349-PGW-xM). Use the shortest possible cable lengths. Water Cooler Connection SPEEDTEC 405S, 405SP, 505S and 505SP work with the water cooler COOLARC 46 (see "Accessories" chapter). WARNING Read and understand the cooler manual before connecting it to the power source. -
Page 10: Machine And Circuit Protection
To connect the water cooler COOLARC 46 to the power Machine and Circuit Protection source: Power Source is protected against overheating, overload Turn off the power source and disconnect input and accidental short-circuits. plug. Remove the cap from the Water Cooler Supply If the machine is overheated, the thermal protection Socket. - Page 11 Technical Service Center or Lincoln Electric. Repairs and modifications performed by unauthorized service or personnel will cause, that the manufacturer’s warranty will become null and void. Any noticeable damage should be reported immediately and repaired.
-
Page 12: Weee
12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine.