Table of Contents
Advertisement
Quick Links
POWERPAK
SOLAR WATER HEATER MODULE
OWNER'S MANUAL
and
WARRANTY / INSTALLATION INFORMATION
MODEL
10 kW
Solahart Industries Pty Ltd ABN 45 064 945 848
Corporate Headquarters: 112 Pilbara Street, Welshpool, Western Australia 6106
Postal address P.O. Box 95, Welshpool, Western Australia 6986
Telephone International +61 8 9351 6400. Facsimile International +61 8 9458 7640
Email
solahart@solahart.com.au
Internet http://www.solahart.com.au
Advertisement
Table of Contents
Related Manuals for Solahart POWERPAK 10 kW
Summary of Contents for Solahart POWERPAK 10 kW
- Page 1 WARRANTY / INSTALLATION INFORMATION MODEL 10 kW Solahart Industries Pty Ltd ABN 45 064 945 848 Corporate Headquarters: 112 Pilbara Street, Welshpool, Western Australia 6106 Postal address P.O. Box 95, Welshpool, Western Australia 6986 Telephone International +61 8 9351 6400. Facsimile International +61 8 9458 7640 Email solahart@solahart.com.au...
-
Page 2: Table Of Contents
POWERPAK Owner’s Manual CONTENTS Introduction System Overview Internal Component Diagram Electronic Controls Installation Instructions Location Selection Collector Array Diagram Collector Installation and Components POWERPAK Module Installation Commissioning System Operation Test Technical Data Warranty Policy Installation Report Issue Date October 2005... - Page 3 POWERPAK Owner’s Manual Issue Date October 2005...
-
Page 4: Introduction
Your POWERPAK solar water heater has been manufactured by a world recognised industry leader, Solahart Industries Pty Ltd. All over the world, the Solahart name is synonymous with quality in water heating. From humble beginnings in the pioneering days of Western Australia, a reputation has been built up over nearly a century. - Page 5 POWERPAK Owner’s Manual Issue Date October 2005...
-
Page 6: System Overview
Solahart collector panels into a separate (remote) potable water storage system using two independent transfer circuits. The primary (or collector) circuit will consist of between 4 and 8 roof or frame mounted Solahart collector panels connected with insulated copper pipes to the ground-mounted POWERPAK energy transfer module. -
Page 7: Electronic Controls
When illuminated both circulating pumps will be prevented from operating. Illumination of the fault light indicates a problem with the system; call a Solahart technician to examine the installation. If the fault light comes on, the following steps must be taken:... -
Page 8: Installation Instructions
The collector panel location should not be more than 7 metres vertically, for a 10kW POWERPAK above the base of the POWERPAK with a maximum pipe run of 16 metres from the POWERPAK. For installations with greater distance than these please consult Solahart for revised pump sizes and configurations. -
Page 9: Collector Array Diagram
POWERPAK Owner’s Manual TYPICAL ARRAY DIAGRAM FOR EIGHT COLLECTORS Temperature Sensor Collector flow connection Collector return connection Expansion Valve connection Top collector rail Bottom collector rail Collector clamps NOTE: The POWERPAK System is suitable for installation with between 4 and 8 collectors. Issue Date October 2005... -
Page 11: Powerpak Module Installation
POWERPAK Owner’s Manual Collector Return Line Connection Final connection is achieved by welding (where solder is permitted, the melting temperature must be greater than 220ºC) a “remote connection pipe” to the insulated copper pipe returning to the POWERPAK system. The remote connection pipe is then inserted into the top collector fitting of Gland Nut the right hand collector. - Page 13 POWERPAK Owner’s Manual Filling the Drain Back Tank 1. Remove both the Fill and Level Plugs (located under the cover for temperature sensor connections at the side of the unit) and insert the two Charging Adaptors. Charging Adaptor. Fill Plug Level Plug Fill &...
-
Page 15: Technical Data
1250 8057 5326 TECHNICAL DATA Dimension Detail 10 kW Module Solahart Collector Panel Details Collector Panel Data • Selective Surface • Absorptivity = 0.93 (± 0.05) • Emittance = 0.12 (± 0.02) • Glass = Low Iron with 94% transmittance... - Page 16 12 months on all components. Conditions 1. The above is subject to an area within a 30 kilometre radius of the Solahart dealer from whom the unit was purchased. Customers outside this area will be subject to freight and travelling charges incurred by the Solahart dealer conducting the work.
-
Page 18: Installation Report
POWERPAK INSTALLATION & WARRANTY REPORT Dear Customer, To register your warranty please ensure the following information is correct then sign and return to our Solahart Industries Pty Ltd freepost address: Solahart Industries Pty Ltd. Reply Paid Perth 354, Welshpool. Western Australia 6106... - Page 19 POWERPAK Owner’s Manual 949100 Issue Date February 2004...