Page 8
Max. 10" (254mm) Depth of Mantel center line 18" (457mm) 55-1/2" (1410mm) from bottom of unit 2" (51mm) 20" (508mm) 18" (457mm) Mantel leg can go in this 5" area (127mm) 40" (1016mm)
Page 9
Left Nailing Strip Nailing Strip Spacer Plates Right Nailing Strip x 12 Must be on Edge Right Nailing Strip Top Nailing Strip Left Nailing Strip 24½” [624mm] 68” [1729mm] 3” [76mm] 48½” [1222mm] 96¼” [2445mm] 44” [1118mm] CHASE 13¾” [348mm] 13¾”...
Page 10
2 x 6 Stud Wall with a FINISHING MATERIAL FireStop 2 x 4 Header Fire Stop Straightrun 10" (254mm) for 8"(203mm) Hot Air Duct NON-COMBUSTIBLE 2 x 4 1/2"(13mm) THICK Stud Wall HEARTH EXTENTION Unit projects out flush with (64mm) non-combustible material (64mm)
Page 11
Rain Cap Storm Collar Roof Flashing Attic Radiation Shield Framing Nailing Strip Outside Fresh Chase Vent Grill Air Duct Hearth Extension Outside Air Inlet Hearth Safety Strip Alternate Position Chase Vent Grill...
Page 14
Use Listed Roof, Offset, or Floor Roof Flashing Support Attic Insulation Shield Use Listed Roof, Offset, or Floor Support Joist Radiation Shield 30 Elbow...
Page 15
Side Connection Exterior Unit Wall Outside Metal Insulated Metal Vent 6” Duct...
Page 16
Jakel AX-2495 Blower Plan View Angle View Fan Transfer Plate Front View Right View Fan 910-175 AX-3088 910-903 910-516 Ground Power Chord 910-619 Neutral - from Fan Ground 919-885 Thermodisc 910-142 P60T12 Variable Switch 910-330 6" (152mm) Min. Ceiling To Rouch Opening Flue Center-line Flex Vent...
FP90 FAN INSTALLATION NOTE: If optional Ashtray is installed, it must be removed before installing the fan. The receptacle Box must be replaced with one that will accept the fan cable. 1) Remove the thumb screw from the fan transfer tray.
Page 23
FP90 6) Slide the thermodisc/cover assembly into the bracket clip on the underside of the fi rebox. Check that no wire will touch the hot surfaces. THE TOP IS ANGLED BACK AT 5 DEGREES TO ENSURE THAT THE TEMPLATE FITS TIGHT TO THE UNIT.
Page 24
WARNING: KEEP MASONRY MATERIAL AT LEAST 1/2" (13mm) FROM THIS TOP FACING GUIDE. THIS IS REQUIRED TO PREVENT MASONRY FACING MATERIAL FROM HITTING THE TOP STIFFENER LOCATED ON THE BACK OF THE SURROUND WHICH IS HIGHER THAN THIS EDGE. INSTALL THE SURROUND TEMPLATE ONTO THE UNIT WITH THE SAME MOUNTING SCREWS AS THE SURROUND.
Page 25
WOOD FIREPLACE EX90 / R90 FINISHING TRIM KIT 1) Unit must be installed correctly according to the specifi cation in the manual. The nailing strips must be attached to the top and sides of the unit. They must be positioned so that they are set-back ½”...
Page 26
WOOD FIREPLACE EX90 / R90 2) Make sure the insulation under the top stand-off is up against the back of the top nailing strip. 3) Fasten the nailing strips to the framing. 4) Install both the left and right side trim (see labels for orientation). The side trims have slotted holes to allow the sides to be adjusted once installed to ensure the top corners will fi...
FIREPLACE SCREEN INSTALLATION EX90 / R90 INSTALLING THE HANDLES ON THE SCREEN INSTALLING THE SCREEN ON THE FIREPLACE 1) 1 or 2 handles can be installed on the screen. Layout 1) Ensure doors are opened enough to allow fi re screen location of the handle using the backing plate as a to be installed.
Page 28
WOOD FIREPLACE REGENCY LOUVERS Installing the Top Louver Installing the Bottom Louver 1) Add two (2) screws (¼-20 X ½”) to the front of the 1) Fasten the bottom louver frame onto the front of fi replace for mounting the top louver. The screws the fi...
Page 29
WOOD FIREPLACE EX90 EXCALIBUR FACEPLATE NOTE: Before installing the fi replace the facing guide must be installed. Installing the Facing Guide Installing the Excalibur Faceplate 1) Secure the left and right facing guides to the fi re- 1) Remove the left and right door from the fi replace. place with seven (7) screws (#10 x 1”) on each side.
WOOD FIREPLACE EX90 ACCENT KIT INSTALLATION Remove the handles by removing the nut and screw. Remove the 2 studs on the sides of the Hood. Insert Install the new handles by placing them in position over the new studs through the holes and secure them by the holes on the surround louver.
Annual Maintenance Completely clean out entire unit Annually Inspect air tubes, baffles and bricks Replace any damaged parts. Adjust door catch / latch If unable to obtain a tight seal on the door - replace door gasket seal. Readjust latch after new gasket installed. Inspect condition and seal of: Glass Gasket Door Gasket...
Page 33
Part # Description Part # Description 1) 001-127 Heat Deflector Top 10) 001-038 Grill Duct - Top 001-128 Stand Off Top - Right Side 001-039 Grill Duct - Bottom 001-129 Stand Off Top - Left Side 001-040F Grill Duct - Plate 001-130 Support Top Stand Off 11) 001-042...
Page 34
Description Description Part # Part # 001-170 Door Latch [Double] 902-534 Brick Liner - Bottom Left Double Door Glass Retaining Rod 001-278 902-535 Vermiculite Liner - Left Side 001-292F Hinge Mounting Plate - Left Male 902-536 Vermiculite Liner - Right Side 815-242 Hinge Pin - Male 902-537...
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.