Land Pride Accu-Z Razor 357-044M Operator's Manual
  1. Manuals
  2. Brands
  3. Land Pride Manuals
  4. Lawn Mower
  5. Accu-Z Razor 357-044M
  6. Operator's manual
Land Pride Accu-Z Razor 357-044M Operator's Manual

Land Pride Accu-Z Razor 357-044M Operator's Manual

Zero turn mowers
Hide thumbs Also See for Accu-Z Razor 357-044M:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Zero Turn Mowers
Z44 & Z52 (S/N 472620 -526170)
23802
Table of Contents
Accu-Z Razor
357-044M
Operator's Manual
!
Read the Operator's manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2010
Printed
Cover photo may show optional
equipment not supplied with
standard unit.
®
4/19/10

Advertisement

Table of Contents
loading

Related Manuals for Land Pride Accu-Z Razor 357-044M

Summary of Contents for Land Pride Accu-Z Razor 357-044M

  • Page 1 Zero Turn Mowers Z44 & Z52 (S/N 472620 -526170) 23802 Table of Contents Accu-Z Razor 357-044M Operator’s Manual Read the Operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ©...

  • Page 2: Table Of Contents

    Copyright 2010 All rights Reserved Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.

  • Page 3: Important Safety Information

    Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label”...
  • Page 4 Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Practice Safe Maintenance Understand procedure before doing work. Use proper tools and equipment, refer to Operator’s Manual for additional information. Work in a clean dry area.
  • Page 5 Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Prepare for Emergencies Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctor, ambulance, hospital and fire department near phone.

  • Page 6: Safety Labels

    Keep all safety labels clean and legible. Replace all damaged or missing labels. To order new labels go to your nearest Land Pride dealer. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified by Land Pride.
  • Page 7 Important Safety Information 4/19/10 Table of Contents 838-307C 23620 Warning: Moving Parts 838-308C Warning: Rotating Blade Hazard 23619 838-833C Warning: Fuel (Imbedded in Fuel Tank) 23620 Z44 & Z52 (S/N 472620 -526170) Accu-Z Razor ® Zero Turn Mowers 357-044M...
  • Page 8 Important Safety Information Z44 & Z52 (S/N 472620 -526170) Accu-Z Razor Table of Contents 838-444C 23643 Danger: Muffler Hot (Both Sides of Engine) 838-310C 23620 Warning: General 818-543C 23643 Danger: Guard Missing ® Zero Turn Mowers 357-044M 4/19/10...

  • Page 9: Introduction

    Introduction Introduction Land Pride welcomes you to the growing family of new product owners. This mower has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance and safe operating practices will help you get years of satisfactory use from the machine.

  • Page 10: Section 1: Assembly & Set-Up

    Section 1: Assembly & Set-up Section 1: Assembly & Set-up Uncrating Instructions The crate is assembled with wire clips. The mower frame is banded to the crate floor. 1. First remove the top panel by prying the wire clips free with a pry bar. Then remove the side panels in the same way.

  • Page 11: Electrical Cable Connection

    Section 1: Assembly & Set-up IMPORTANT: Do not pull a trailer or implement exceeding 300 pounds towing capacity and 50 pounds tongue weight. Loss of control may result. Do not make turns that will cause a trailer or implement being towed with the hitch to come in contact with the mower or damage may result.

  • Page 12: Section 2: Operating Procedures

    Section 2: Operating Procedures Section 2: Operating Procedures Mower Features Refer to Figure 2-1 Your Razor riding mower is designed with innovative and state-of -the art features. Knowing the location and how Muffler Shield Is Located Under the Engine Blade Engagement Switch Oil Pressure Light Ignition Switch Hour Meter...

  • Page 13: Operating Check List

    Section 2: Operating Procedures Operating Check List Hazard control and accident prevention are dependent upon awareness, concern, prudence and proper training involved in operation, transport, maintenance and storage of the riding mower. Therefore, it is absolutely essential that no one operates the mower without first having read, fully understood and become totally familiar with the Operator’s Manual.

  • Page 14: Blade Engagement Switch

    Section 2: Operating Procedures Blade Engagement Switch Refer to Figure 2-2: The Blade engagement switch engages the deck blades. Pull switch up to engage blades and push switch down to disengage the blades. IMPORTANT: Never engage blades with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged.

  • Page 15: Deck Lift Pedal

    11. Replace the seat safety switch if the switch failed to operate properly in any of the above steps and if no other cause such as damaged wiring can be determined. 12. Contact your local Land Pride Dealer if the problem cannot be located. Deck Lift Engine Starting...

  • Page 16: Driving The Mower

    Section 2: Operating Procedures NOTE: The engine starter should not be operated for periods longer then 30 seconds at a time. An interval of at least two minutes should be allowed between such cranking periods to protect the starter from overheating and burn-out.

  • Page 17: Moving Mower With Stalled Engine

    Section 2: Operating Procedures Moving Mower with Stalled Engine Refer to Figure 2-9: Each hydro-drive is equipped with a bypass valve for the purpose of moving the mower when the engine is inoperable.To bypass the hydro-drives, pull out on the bypass valve rods and lift them into the slot to lock in position.

  • Page 18: Safe Operating Instructions

    Section 2: Operating Procedures Safe Operating Instructions The safe operation of any machinery is a big concern to all consumers. Your Zero Turn Riding Mower has been designed with many built-in safety features. However, no one should operate this mower before carefully reading this Operator’s Manual.
  • Page 19 Section 2: Operating Procedures DANGER Prior to operating the mower the operator should be thoroughly familiar with the proper use and operation of the equipment, should read the manual completely and thoroughly, and should have attempted slow moving maneuvers to become familiar with the operation of the equipment before attempting normal speed operation.

  • Page 20: Mower Deck Operation

    Section 2: Operating Procedures Mower Deck Operation DANGER Never attempt to make any adjustments to the mower deck while the engine is running or when the blades are engaged. Mower blades cannot be seen and are located very close to deck housing.

  • Page 21: Section 3: Adjustments

    Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride service center when assistance is needed. Torque Values WARNING Particular attention must be given to tightening the drive wheel lug nuts and blade spindle bolts.

  • Page 22: Control Lever Neutral Adjustment

    Section 3: Adjustments Control Lever Neutral Adjustment Before considering any adjustment, check tire air pressure and make certain hydraulic oil is at operating temperature. Unequal tire pressure will cause mower to drift to one side. Refer to “Tire Inflation Chart” on page 22 and page 44.

  • Page 23: Seat Adjustment

    Section 3: Adjustments 3. Repeat step 2 to adjust the right dampener rod. 4. Check steering dampeners: a. Move the control levers to reverse position and release. The control levers should return to neutral position. b. Repeat steps 1 through 4 if control levers do not return to neutral position.

  • Page 24: Hydro-Drive Belt Adjustment

    Section 3: Adjustments Hydro-Drive Belt Adjustment The pump drive belt tension remains constant by means of a tension idler and spring. There is no tension adjustment of this belt. Deck Drive Belt Adjustment The spindle belt remains in constant tension by means of a spring tensioned idler.
  • Page 25 Section 3: Adjustments Refer to Figure 3-8: 5. Set cutting height at 3 1/4” on the height indicator by placing the height adjusting stop in the 3” hole, and turning the height adjustment stop so that the flat side is against the stop handle. 6.
  • Page 26 Section 3: Adjustments Refer to Figure 3-12: 9. Start the leveling process on the left front side of the mower. 10. Set the amount of threads on the deck lift rod to protrude approximately 1” pass the lift block. 11. Jam both nuts against the lift block. 12.

  • Page 27: Deck Cutting Height Adjustment

    Section 3: Adjustments Refer to Figure 3-12 on Page 24: 27. Compress the deck lift assist springs so that there is 1” of space between the front nut and on the spring and the rear nut on the deck lift block. Typical both sides.

  • Page 28: Section 4: Maintenance & Lubrication

    Section 4: Maintenance & Lubrication Section 4: Maintenance & Lubrication 23643 Top View (Honda Engine Shown) Oil fill & dip stick (1), fuel filter (2), Oil filter (8) and fuel tank valve (17) are located on the left side for the Briggs & Stratton engine 23687 Deck Bottom View Z44 &...

  • Page 29: Maintenance Schedule

    Section 4: Maintenance & Lubrication Service at Intervals Indicated Clean mower, Deck & Engine Cooling System Verify Safety Start Interlock System Inspect Unit for loose hardware and damage Visually Inspect Tires Check Engine Oil Level Clean Air Intake Screen Check Fuel Level Blades - Sharp &...

  • Page 30: Maintenance

    Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride dealer when assistance is needed. Torque Values WARNING Particular attention must be given to tightening the drive wheel lug nuts, blade spindle bolts and electric clutch bolt.

  • Page 31: Tires

    Section 4: Maintenance & Lubrication Tires Use only tires recommended by Land Pride. Solid fill tires are not to be used on the Razor mower. It is important for your safety and the safety of others that the tires have correct air pressure. Check air pressure in all four tires before each use.

  • Page 32: Access To Izt Units

    200 hours or every 2 years whichever comes first. Filter replacement kit #356-552A may be purchased from your nearest Land Pride dealer. The Kit contains two filters and two magnetic plugs. Change hydraulic oil and oil filter as follows: 1.

  • Page 33: Fuel System

    Section 4: Maintenance & Lubrication 3. Clean the exterior of the unit of any debris before removing the oil filter and magnetic plug. 4. Remove oil filter from underside of pump with 3/8” allen wrench and allow oil to drain completely. IMPORTANT: The filter is plastic, excessive torque will damage filter.

  • Page 34: Fuel Filter

    Section 4: Maintenance & Lubrication Fuel Filter Refer to Figure 4-7: DANGER Close fuel shut-off valve before replacing fuel filter. Otherwise, fuel can leak out creating a fire and/or explosion hazard. The fuel filter is installed in the fuel line between the Left/Right Fuel Tank Valve and engine fuel pump.

  • Page 35: Engine Air Filter

    Section 4: Maintenance & Lubrication Engine Air Filter Perform engine air filter maintenance per the engine operator’s manual. General Engine Maintenance Detailed instructions and recommendations for break-in and regular maintenance are specified in the engine operator’s manual. Please refer to this manual for engine servicing, lubricating oil levels with quality and viscosity recommendations, bolt torques, etc.

  • Page 36: Drive Belt Replacement Instructions

    Section 4: Maintenance & Lubrication Drive Belt Replacement Instructions Refer to Figure 4-11 on page 33: 1. Park unit on a flat surface. Stop engine and remove ignition key. Make sure blade engagement switch is in the down (OFF) position. Spread control levers fully apart and set park to (ON).
  • Page 37 2. With a 11/16” wrench, remove the 1/2” center blade bolt and Washer from the bottom of the blade. IMPORTANT: Replace blades with Land Pride blades only. IMPORTANT: Always install blades with cutting edge facing direction of blade spindle rotation and with wing tips pointing up towards bottom of deck.

  • Page 38: Storage

    A coating of oil may also be applied to the deck underside to minimize oxidation. 3. Clean and touch up all scrapes with Land Pride spray paint. 4. Check blades and blade bolts for wear and replace if necessary.

  • Page 39: Lubrication Points

    Section 4: Maintenance & Lubrication Lubrication Points Lubrication Multi-purpose Legend spray lube 4/19/10 Table of Contents Multi-purpose Multi-purpose grease lube oil lube Center Blade Spindle Through opening between front shields. 1 Zerk Type of Lubrication: Multi-purpose Grease Quantity = As required 23707 Left Blade Spindle Under lower edge of pulley cover.

  • Page 40: Gauge Wheel Bearing Zerk

    Section 4: Maintenance & Lubrication See Note 23685 Z44 & Z52 (S/N 472620 -526170) Accu-Z Razor Table of Contents Gauge Wheel Bearing Zerk Located on hub of gauge wheel 2 Zerks (One on each gauge wheel) Type of Lubrication: Multi-purpose Grease Quantity = As required NOTE: Caster spindles have sealed bearings and require no servicing.

  • Page 41: Section 5: Specifications & Capacities

    8.3:1 32.5 FT. LBS @ 2500 RPM 2 US quarts 2.3 US quarts 831-053C 831-054C None Replaceable, Automotive-Type Land Pride Part No. 831-035C Air cooled, Fly-wheel fan ® (General Specifications) 44" 0.1" 49.7” 43.8” 67.9” w/Honda Engine 68.7" w/Briggs & Stratton Engine 720 lbs.
  • Page 42 Section 5: Specifications & Capacities Z44 & Z52 Accu-Z Razor Ground Speed Steering Type Twin Lever Steering Controls Steering Turning Radius Brake Service Parking Mower Drive Safety Features Seat Mainframe Construction Drive Motor Mount Front Caster Wheels Front Caster Forks Deck Thickness Box-Section Reinforced Front Edge...

  • Page 43: Section 6: Features And Benefits

    Section 6: Features and Benefits Section 6: Features and Benefits Features 44” or 52” Cutting width Sized and priced right for residential owners. Ground speed Forward 0-7 mph and Reverse 0-5 mph for high mowing productivity Mid-mount deck design Mid-mount design puts the deck closer to the operator’s line of sight for a more efficient and precise operation.

  • Page 44: Section 7: Troubleshooting

    Section 7: Troubleshooting Section 7: Troubleshooting Symptoms Starting motor does not crank Engine cranks but does not start Engine: Runs with continuous misfiring or engine runs unevenly or erratically Grass cutting is ragged or uneven Loss of power or system will not operate in either direction Overheating Low oil pressure...
  • Page 45 Section 7: Troubleshooting Symptoms High oil consumption Mower jerky when starting or operates in one direction only Hydraulic system operates hot Mower creeps when steering control levers are in neutral Mower circles or veers in one direction Mower creeps with park lever engaged 4/19/10 Table of Contents Probable Causes...

  • Page 46: Section 8: Appendix

    Section 8: Appendix Section 8: Appendix Bolt Head Identification Bolt Size (Inches) Grade 2 Grade 5 in-tpi N·m ft-lb N·m 1/4" - 20 1/4" - 28 5/16" - 18 5/16" - 24 3/8" - 16 3/8" - 24 7/16" - 14 7/16"...

  • Page 47: Warranty

    This Warranty does not apply to any part or product which in Land Pride’s judgment shall have been misused or damaged by accident or lack of normal...
  • Page 48 Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...

This manual is also suitable for:

Accu-z razor z44Accu-z razor z52

Table of Contents