Land Pride RC35120 Operator's Manual
  1. Manuals
  2. Brands
  3. Land Pride Manuals
  4. Lawn Mower
  5. Rotary Cutter RC35120
  6. Operator's manual
Land Pride RC35120 Operator's Manual

Land Pride RC35120 Operator's Manual

Rotary cutter
Hide thumbs Also See for RC35120:
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's Manual
Operator's Manual
Cover photo may show optional equipment not supplied with standard unit.
!
Read the Operator's manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious - follow without exception. Your life and the lives
of others depend on it!
© Copyright 2008 Printed
Table of Contents
7/14/08
RC35120 RCM35120
Rotary Cutter
10438
312-301M

Advertisement

Table of Contents
loading

Related Manuals for Land Pride RC35120

Summary of Contents for Land Pride RC35120

  • Page 1 Table of Contents Operator’s Manual Operator’s Manual RC35120 RCM35120 Rotary Cutter 10438 Cover photo may show optional equipment not supplied with standard unit. Read the Operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ©...

  • Page 2: Table Of Contents

    Copyright 2008 All rights Reserved Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.

  • Page 3: Important Safety Information

    Make sure everyone that uses this machine has read the and securely block cutter on safe supporting stands. Do not Operator’s Manual and understands how to operate it position stands under axle or wheel supports. safely. 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 4: Safety Labels

    To Your implement comes equipped with all safety labels in place. order new labels go to your Land Pride dealer. They were designed to help you safely operate your implement.
  • Page 5 Table of Contents Land Pride Important Safety Information 818-187C 14275 Danger PTO Shield 818-229C 14274 Amber Reflector 818-230C 14280 Red Reflector 818-240C Caution 1000 RPM 14272 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...
  • Page 6 Important Safety Information ROTATING DRIVELINE KEEP AWAY! 818-552C 14272 Danger PTO Driveline ROTATING DRIVELINE KEEP AWAY! 818-552C 14275 Danger PTO Driveline ROTATING DRIVELINE KEEP AWAY! 818-552C 14279 Danger PTO Driveline 818-554C Warning General 14273 Cutter Safety RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 7: Rc35120 Rcm35120 Rotary Cutter 312-301M

    Table of Contents Land Pride Important Safety Information 818-555C 14273 Danger Rotating Blade 818-556C 14273 Danger Thrown Object 818-557C Notice To Owner 14273 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 8: Introduction

    Table of Contents Land Pride Introduction Introduction Land Pride welcomes you to the growing family of new only be replaced with genuine Land Pride parts. product owners. This implement has been designed with Serial Number Plate care and built by skilled workers using quality materials.

  • Page 9: Section 1 Assembly And Setup

    (#10) and 1 1/2" x 1" x 1 7/8" a. Install 3 1/2" x 8" hydraulic cylinder (#17) and se- long spacer (#11) on outboard side of pivot, and 1 cure with 1" pins and clips furnished with cylinder. 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 10: Tailwheel

    3. Attach tailwheel yoke spindle (#28) to caster arm Rubber Bumper Tightening Dimensions weldment (#18) and secure with washer (#29) on bot- Figure 1-2 tom and washer (#30) on top and spiral roll pin (#31). RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 11: Pull-Type Cutter

    2. Assemble tongue to lower hitch plates welded to cut- 5. Install jack (#11) to tongue and secure with pin (#12). ter deck with the 1 5/8” x 1 1/8” x 2” long spacers (#2), Tongue Assembly Figure 1-3 14257 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 12: Rear Axle

    1. Attach axle arm weldment (#11) to axle arm mount the cutter after attaching cutter to tractor. with 1” pin (#12) and secure with 5/16” x 2” long bolt (#16) and lock nut (#14). 14258 Pull-Type Tailwheel & Rear Axle Assembly Figure 1-4 RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 13: Driveline Installation

    1. Be certain that tractor draw bar will not interfere. Move draw bar ahead, aside or remove if required. Draw bar should also be checked for clearance when unit is be- ing raised for the first time. Lift-Type Tractor Hook-Up Figure 1-6 14261 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...
  • Page 14 Refer to Figure 1-9: cutter gearbox. 10. If check chain kit is purchased, assemble to cutter. 14260 Check Chain Assembly Figure 1-9 RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 15: Pull-Type Cutter

    Round off all sharp edges and remove burrs. 9. Slide PTO shaft over tractor’s splined shaft and secure Grease sliding profiles. with locking device of PTO shaft. 14262 Pull-Type Tractor Hook-Up Figure 1-10 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 16: Section 2 Operating Instructions

    5. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely. speed. Loss of PTO speed will allow the blades to hinge back and result in ragged, uneven cutting. RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...
  • Page 17 CAUTION! residues. Do not over speed PTO or machine damage may result. This cutter (RC35120) designed to be used only with a tractor having CAUTION! a 540 RPM rear PTO. The RCM35120 is designed to be used with a tractor having a 1000 RPM PTO.

  • Page 18: Section 3 Adjustments

    Turn nut on leveling tube counterclockwise to low- er front of cutter and clockwise to raise front of cut- ter. g. Secure with jam nut. Deck Attitude Adjustment Figure 3-2 14264 RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 19: Section 4 Troubleshooting

    Cutting height not level Adjust cutter height Soil abrasive Adjust cutter height Cutting too low Adjust cutter height Tail wheel support failing Lowering too fast Adjust rate of drop Hitting objects when turning Reduce speed on turns 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...
  • Page 20 Blades loose Tighten blade bolts Blade carrier bent Replace blade carrier Blade broken Replace blade Blade will not swing Remove and inspect blade Blades have unequal weight Replace both blades Blades locked together Unlock blades RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 21: Section 5 Maintenance And Lubrication

    Replace any worn, damaged or illegible safety decals by 1. Check skid runners and skid shoes for wear and re- obtaining new decals from your Land Pride Dealer. place if necessary. Order skid shoe Land Pride part # Service Cutting Blades 312-175D or 312-079A (1 set with hardware).

  • Page 22: Clutch Run-In

    The clutch should slip during operation to protect the cut- 6. Repaint parts where paint is worn or scratched to pre- ter from excessive loads. vent rust. Ask your dealer for Aerosol Land Pride Beige touch-up paint #821-011C. Prior to initial operation and after long periods of inactivity, the Friction Clutch should be "run-in".

  • Page 23: Lift-Type Tailwheel Hub

    14267 Quantity = Until grease purges from the relief hole Required Ratchet Jack Type of Lubrication: Multi-Purpose Quantity = As required 14176 Driveline U-Joints Type of Lubrication: Multipurpose Grease Quantity = 6 pumps 14190 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 24: Driveline

    Reinstall plugs and tighten. 14271 NOTE: Do not overfill! Cutter should be level when checking oil. Type of Lubrication: EP90 Oil Quantity = fill until oil flows from the side port of t-box case. RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 25: Plate Slip Clutch

    Step 6 Install bottom backup ring, compres- sion spring, lock collar, and top back- up ring. Step 6 Inspect friction disks and hub. Step 7 Install snap ring. 14232 14233 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 26: Section 6 Specifications And Capacities

    Tailwheel Lift-Type - 4.00 x 8 x 15 1/4 Laminated Tires Pull-Type - 6.00 x 9 x 21 Laminated or 5 x 15 Rim Gauge Wheel Shock Load Protection Four Shock Absorbing Rubber Bumpers RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 27: Section 7 Appendix

    1 1/2" - 12 1330 2970 2190 4820 3560 mm x pitch = nominal thread dia. in millimeters x thread pitch Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. 7/14/08 RC35120 RCM35120 Rotary Cutter 312-301M...

  • Page 28: Notes

    Table of Contents Land Pride Section 7 Appendix Notes RC35120 RCM35120 Rotary Cutter 312-301M 7/14/08...

  • Page 29: Warranty

    Pride and the installation by the dealer of any such replacement part and does not cover common wear items such as blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
  • Page 30 Great Plains Manufacturing, Inc. Corporate Office: PO. Box 5060 Salina, Kansas 67402-5060 USA...

This manual is also suitable for:

Rcm35120

Table of Contents