Land Pride RCP2660 Operator's Manual
  1. Manuals
  2. Brands
  3. Land Pride Manuals
  4. Lawn Mower
  5. RCP2660
  6. Operator's manual
Land Pride RCP2660 Operator's Manual

Land Pride RCP2660 Operator's Manual

Parallel arm rotary cutter
Hide thumbs Also See for RCP2660:
Table of Contents

Advertisement

Quick Links

Download this manual
Parallel Arm Rotary Cutter
RCP2660, RCPM2660, RCP3060 & RCPM3060
30028
Table of Contents
!
Read the Operator's Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator's Manual and Decal Kit in French
Language, please see your Land Pride dealer.
316-111M
Operator's Manual
Printed 11/2/18

Advertisement

Table of Contents
loading

Related Manuals for Land Pride RCP2660

Summary of Contents for Land Pride RCP2660

  • Page 1 Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit. For an Operator’s Manual and Decal Kit in French Language, please see your Land Pride dealer. Printed 11/2/18...

  • Page 2: Machine Identification

    Machine Length Machine Width Machine Weight Delivery Date First Operation Accessories Dealer Contact Information Name: Street: City/State: Telephone: Email: California Proposition 65 WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov RCP2660, RCPM2660, RCP3060 & RCPM3060 Parallel Arm Rotary Cutter 316-111M 11/2/18...
  • Page 3 Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
  • Page 4 Download the appropriate App on your Refer to Parts Manual QR smart phone, open the App, point your Locator on this page for phone on the QR code and take a picture. detailed instructions. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 5: Important Safety Information

     Important Safety Information Important Safety Information Listed below are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look for the Safety Alert Symbol Careful operation is your best The SAFETY ALERT SYMBOL indicates there is a assurance against an accident.

  • Page 6: Tire Safety

     Lower implement to the ground and  Replace parts on this implement implement. follow all shutdown procedures with genuine Land Pride parts only.  Attach the chain to the tractor before leaving the operator’s seat to Do not alter this implement in a way drawbar support or other specified perform maintenance.
  • Page 7 Use Seat Belt and ROPS signals are recommended Keep Riders Off whenever driving on public roads. Machinery  Land Pride recommends the use of a CAB or roll-over-protective-  Never carry riders on tractor or structures (ROPS) and seat belt implement.

  • Page 8: Safety Labels

    818-045C Warning - Pinch Point Hazard 2-Places 22057 838-368C 22058 Warning - Pinch Point Hazard 818-142C Danger - Rotating Driveline Hazard 26694 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 9 2" x 9" Amber Reflector 30031 838-614C 2" x 9" Red Reflector 30032 838-614C 2" x 9" Red Reflector 35948 818-230C 1 11/16 x 2 13/16" Red Reflector (2 places) 22007 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 10 Table of Contents Important Safety Information 22006 818-830C Warning/Danger/Notice - Combination Safety Decal 818-556C Danger - Thrown Object Hazard (3-Places) 22006 818-555C Danger - Rotating Blades Keep Away 22006 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 11 Warning - High Pressure Fluid Hazard 22007 818-391C Warning - Tractor Roll Over Hazard 30032 818-390C Warning - Thrown Object Hazard 30032 818-564C Danger - Keep Away Rotating Blade Hazard 22007 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 12 30032 818-831C Warning - High Pressure Fluid Hazard 316-362S Socket mounted Slow Moving Vehicle Sign Offered as an Accessory. See “Slow Moving Vehicle Sign (Accessory)” on page 41. 37625 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 13 (Used only on RCPM2660 & RCPM3060 Series) Important - Operate only with 1000 rpm power take-off 12324 818-388C 30032 Important - Valve must be open 848-369C Caution: Avoid Injury or Machine Damage 30033 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 14: Using This Manual

    Serial Number Plate Location “Right” or “Left” as used in this manual is determined by Figure 1 facing the direction the implement will operate while in use unless otherwise stated. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 15: Further Assistance

    3. For further assistance write to: Land Pride Service Department 1525 East North Street P.O. Box 5060 Salina, Ks. 67402-5060 E-mail address lpservicedept@landpride.com 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 16: Wheel Base

    Rear Wheel Base ....74" minimum RCP3060 & RCPM3060 Rear Wheel Base ....95" minimum RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 17: Protective Equipment Requirements

    PROTECTIVE STRUCTURE REQUIRED OPERATOR LEFT-HAND DUAL PROTECTIVE OR LEFT-HAND SHIELD WHEEL WEIGHTS 12,000 LBS. MIN. 47" MIN (SEE TEXT) 95" MIN 24583 RCP3060 & RCPM3060 Minimum Tractor Requirements Figure 1-2 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 18: Dealer Preparations

    Attach the lower arms to the clevises Safety decals are legible and undamaged from with hitch pins and secure with linchpins. shipment. Power take-off driveline and loose parts bag/box shipped with the cutter are present. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 19: Driveline Installation

    IMPORTANT: An additional driveline may be required if implement is attached to more than one tractor or if a Quick Hitch is used. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 20: Check Driveline Collapsible Length

    9. Push/pull on driveline yokes to be certain they are securely fastened to the power take-off shaft and speed increaser input shaft. 10. If driveline yoke will not lock in place, skip to “Check Driveline Collapsible Length” below. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 21: Check Driveline Interference

    Kubota turnbuckles. Refer to “Deck clearance. Move drawbar ahead, aside, or remove if Level Adjustments” on page 33 and “Attach Stabilizer required. Turnbuckles” on page 45. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 22 Transport Safety Chain investigate the problem and correct before continuing. 22031 Once unhooked, store safety chain on the storage hook. Transport Safety Chain Shown Hooked for Transport Figure 1-9 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 23 (#4), flat washers (#7), and hex nylock nuts (#6). Tighten nylock nuts to the correct torque. 3. Insert weight retainer pin (#2) through holes in weight hanger and secure with hairpin cotters (#8). 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 24 2. Cut ties securing A-frame (#2) and rotate frame back 4. Secure yoke spindle to frame with 5/16" dia. roll to position it behind the deck as shown. pin (#7). RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 25 “ON” and “OFF” at the tractor’s power take-off shaft. For detailed set-up instructions, see “Solenoid Control” on page 24. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 26: Hydraulic Hose Hook-Up

    2. Remove transport safety chain from its latched position and place loose end on the storage hook. 3. Start tractor and adjust 3-point hitch until driveline is approximately level. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 27 Refer to “Turtle/Rabbit Flow Control at the before proceeding. The cylinders and hoses will Tractor” on page 32 for detailed instructions. require approximately 1 3/4 gallons from tractor reservoir. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 28: Solenoid Control

    “Hydraulic Flow Control” on page 32. return line. Fittings to plumb to tractor sump or motor Skip to “Solenoid Valve Block Functions” on page 25. return line are customer supplied. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 29: Independent Control

    32. Be sure to set flow control poppet valves. valve knob on the 3-point frame (See Figure 3-1 on page 32) to the lowest possible number. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 30: Control Sticks

    “Deck Motor”. Light is on when running. 30019 • One “ON/OFF” lighted push button switch for “Deck Independent Control With Gauge Wheels Float”. Light is on when deck is floating. Figure 2-10 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 31 Exact location should be convenient for the operator. b. When in use, grip the control stick such that the push button switches are easy to access. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 32 4. “ARM 1” push buttons are not bypassed. “ARM 1 IN” can be pressed to move deck closer and “ARM 1 OUT” can be pressed to move deck farther away. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 33 2. Start tractor and adjust 3-point hitch until driveline is approximately level. Control Stick Shown with Float Switch 25849 Independent & Solenoid Controlled Parallel Arm Movement Figure 2-13 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 34 Cycle the cylinders to full extension and retraction several times to make sure all air is purged. Control Stick Shown with Float Switch 25849 Independent & Solenoid Controlled Parallel Arm Movement (Continued) Figure 2-14 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 35 2. Check Hydraulic Reservoir shut-off valve. Make sure it is fully OPEN before engaging power take-off. 3. Position cutter deck just a few inches above ground or concrete surface. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 36: Section 3: Adjustments

    22030 4. Adjust flow control knob (See Figure 3-1) until cycle Cycle Time (Fully Extended to Fully Retracted) time is 5 seconds. Figure 3-2 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 37: Deck Level Adjustments

    5. Extend “ARM 1” cylinder until gauge wheels are adjust rear gauge wheel until deck rear is 1/2" higher 1 to 2 inches off the ground. than deck front. 27849 Deck Level Adjustments Figure 3-3 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 38: Operating Checklist

    Ensure that both blade bolts and center blade 4. Manually hook transport safety chain to deck hook as carrier hub nuts are tight. shown in Figure 1-9 on page 18. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 39: Section 4: Operating Procedures

    Do not use a power take-off adapter. The adapter will increase strain on the tractor’s power take-off shaft causing possible damage to shaft and driveline. It will also defeat the purpose of the tractor’s power take-off shield. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 40 IMPORTANT: Your cutter is equipped with free swinging cutting blades to reduce shock loads. The blades can lock together in transport. Always check for locked blades before starting to cut. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 41: Shear Bolt Replacement

    3-point hitch. IMPORTANT: Install self-locking nut onto shear bolt until nut is threaded to within approximately 1/32" of contact with clevis as shown in Figure 4-2. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 42 (#9A & #9B). 10. Attach turnbuckles (#9A & #9B) to the lower link mounts (#1 & #2) with lower bent pins (#10) and hairpin cotters (#11). RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 43 4. Place gear selector in park or set park brake, lower 3-point arms down, shut tractor engine off, and remove switch key before dismounting tractor. 37625 Relocate Slow Moving Vehicle Sign Figure 4-3 Parked Position Figure 4-4 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 44 1000 rpm for RCPM2660 and RCPM3060 series cutters. Proceed forward at a mowing speed that is comfortable and will produce a quality controlled cut for ground conditions and material density. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 45 An Slow Moving Vehicle Sign “ON/OFF” push button switch is included on the control Figure 5-1 stick to activate the motor on the deck. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 46 Pride weight hangers designed for that brand. the tractor, parallel arms should be fully extended and the deck should be approximately horizontally level. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 47 International Harvest Suitcase Weight Bolt-on Weight Hanger Part No. 316-230A Bolt-on Weight Hanger Part No. 316-232A Use only with illustrated John Deere suitcase weights Bolt-on Weight Hangers Figure 5-3 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 48 10. Secure hitch pin (#14) with linchpin (#15). 11. Tighten hex lock nuts (#5) to the correct torque. 12. Repeat steps 7-11 to attach right-hand lower link mount (#2) to the inside of clevis plate (#19). RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 49 Cat. lll hitch pin holes with flanges on the inside as shown. 10. Install a new Cat. ll hitch pin (#20) and secure with a new hitch pin keeper. Customer to supply hitch pin and hitch pin keeper. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 50: Section 6: Hydraulic Plumbing

    Order only genuine Land Parts from your local Land Pride dealer. 27974 Remote Cylinder Plumbing For Tractor Control Figure 6-1 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 51 Flow Control Valve (16 gpm & Above) Figure 6-3 Figure 6-4 See Figure 6-3 and Figure 6-4 Return Line Pressure Line Solenoid Control Box 27975 Hydraulic Cylinder Plumbing for Solenoid Control Option Figure 6-5 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 52 Pressure Overpressure Relief Valve Solenoid with Float Cylinder Pump Control Capabilities Figure 6-9 Shut Off 35 Gallon Valve Reservoir 27967 Cylinder Pump Plumbing for Independent Control Option Figure 6-7 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 53 Pressure Line Motor Pump Deck Motor Switch Deck Motor Relief Valve Shut Off 35 Gallon Valve Reservoir See Figure 6-7 27966 Deck Motor Plumbing for Independent Control Option Figure 6-9 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 54: Section 7: Electrical Wiring Schematics

    Section 7: Electrical Wiring Schematics Section 7: Electrical Wiring Schematics Solenoid Control Option Wiring Schematic Without Gauge Wheels Refer to Figure 7-1: 25852 Wiring Schematic For Solenoid Control Without Gauge Wheels Figure 7-1 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 55 Table of Contents Section 7: Electrical Wiring Schematics Wiring Schematic With Gauge Wheels Refer to Figure 7-2: 25851 Wiring Schematic For Solenoid Control With Gauge Wheels Figure 7-2 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 56 Table of Contents Section 7: Electrical Wiring Schematics Independent Control Option Wiring Schematic Without Gauge Wheels Refer to Figure 7-3: 39078 Wiring Schematic For Independent Control Without Gauge Wheels Figure 7-3 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 57 Table of Contents Section 7: Electrical Wiring Schematics Wiring Schematic With Gauge Wheels Refer to Figure 7-4: 30025 Wiring Schematic For Independent Control With Gauge Wheels Figure 7-4 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 58: Section 8: Maintenance & Lubrication

    Do not attempt to modify a blade such as hard surfacing, heat treating, cold treating, or by any other method. Always replace blades with new Land Pride blades to assure safety. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 59 9. If replacing dishpan (#4), castle nut (#10) on gearbox output shaft should be torqued to 550 ft-lbs. minimum and secured with cotter pin (#11) with both legs bent opposite directions around the nut. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 60: Skid Shoes

    3. Attach new skid shoe (#1) to cutter with existing 3/8" plow bolts (#2) and secure with 3/8" hex whiz nuts. Torque to 31 ft. lbs. 4. Repeat on opposite side. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 61: Hydraulic Hose Replacement

    These simple maintenances will go a long way to prevent the occurrence of solenoid valve and hydraulic cylinder problems on the Parallel Arm Rotary Cutter. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 62: Long Term Storage

    Store the cutter in a clean dry place with deck positioned on a flat surface. 8. Retracted parallel arms, raise deck up and hook transport safety chain to the deck hook. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 63 Type of Lubrication: Multi-purpose Grease 30030 Hours Deck Pivot 3 - Zerks Type of Lubrication: Multi-purpose Grease 30030 Hours Parallel Arm Pivot 1 - Zerk Type of Lubrication: Multi-purpose Grease 30030 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 64 2 - Zerks per wheel (3- wheels) Type of Lubrication: Multi-purpose Grease 24622 Required Ratchet Jack 2 - Zerks per jack (2-jacks) Type of Lubrication: Multi-purpose Grease Quantity - As Required 24621 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 65 Be sure to reinstall drain plug and tighten before filling gearbox. Fill gearbox 12270 with 80-90W EP gearlube. Reinstall level plug and tighten. Replace breather/fill cap. Speed Increaser Figure 8-9 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...
  • Page 66 Extruded aluminum frame and glazed with 1/4" clear lexan polycarbonate Kubota 3-Point Stabilizer Kit Available Not available Slow Moving Vehicle Sign Slow moving decal on galvanized steel back sign and plated or galvanized mount. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...
  • Page 67 Table of Contents Section 9: Specifications & Capacities 22005 Overall Dimensions 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 68: Section 10: Features & Benefits

    RCP hydraulic system to operate the cutter. Tractor needs one set of hydraulics to operate the breakaway cylinder. Makes the RCP2660 Parallel Arm Rotary Cutter a match fit for Kubota tractor model Kubota 3-Point Stabilizer Kit M126GX, M135GX, M6-141, and M6-141.

  • Page 69: Section 11: Troubleshooting

    Hoses not connected to proper duplex outlet Connect hoses to proper tractor outlet. on tractor Defective solenoid on cartridge valve assy. Replace solenoid. Solenoid valves is sticking. Remove/clean/replace solenoid valve. 11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:...

  • Page 70: Torque Values Chart For Common Bolt Sizes

    Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. Additional Torque Values Blade Bolt Locknut 450 ft-lbs. Blade Carrier Hub Nut 450 ft-lbs. RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M: 11/2/18...

  • Page 71: Warranty

    This Warranty is limited to the repair or replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items such as blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
  • Page 74 Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...

This manual is also suitable for:

Rcpm2660Rcp3060Rcpm3060

Table of Contents