FUNAI WD6D-M100 Service Manual
  1. Manuals
  2. Brands
  3. FUNAI Manuals
  4. DVR
  5. WD6D-M100
  6. Service manual

FUNAI WD6D-M100 Service Manual

Dvd/ video cassette recorder
Hide thumbs Also See for WD6D-M100:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
SERVICE MANUAL

Main Section

I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA
I Exploded Views
I Parts List
CASSETTE RECORDER
DVD / VIDEO
WD6D-M100
When servicing the deck
mechanism, refer to MK14 Deck
Mechanism Section.
Deck Mechanism Part No.:
N25E1FL

Advertisement

Table of Contents
loading

Related Manuals for FUNAI WD6D-M100

Summary of Contents for FUNAI WD6D-M100

  • Page 1 When servicing the deck I Specifications mechanism, refer to MK14 Deck I Preparation for Servicing Mechanism Section. I Adjustment Procedures I Schematic Diagrams Deck Mechanism Part No.: I CBA I Exploded Views N25E1FL I Parts List DVD / VIDEO CASSETTE RECORDER WD6D-M100...

  • Page 2: Table Of Contents

    MAIN SECTION DVD / VIDEO CASSETTE RECORDER WD6D-M100 Main Section I Specifications I Preparation for Servicing I Adjustment Procedures I Schematic Diagrams I CBA I Exploded Views I Parts List TABLE OF CONTENTS Specifications ................1-1-1 Laser Beam Safety Precautions.

  • Page 3: Specifications

    SPECIFICATIONS General VCR video heads Four heads Power requirements 220–240 V ± 10 %, 50 Hz ± 0.5 % Power consumption 35 W Power consumption (standby) 0.5 W (When “Antenna Out” is set to “OFF”) Weight 5.0 kg Dimensions (width x height x depth) 435 x 99.5 x 388 mm Operating temperature 5°C to 40°C...

  • Page 4: Laser Beam Safety Precautions

    LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Product Safety Notice K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the Some electrical and mechanical parts have special AC outlet. safety-related characteristics which are often not L. Be sure to confirm the FAN motor has completely evident from visual inspection, nor can the protection stopped when disconnecting the AC cord for they give necessarily be obtained by replacing them...
  • Page 6 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the Chassis or Secondary Conductor specified values to verify compliance with safety standards.

  • Page 7: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
  • Page 8 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 9 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 10 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 11: Preparation For Servicing

    PREPARATION FOR SERVICING How to Enter the Service Mode About Optical Sensors Caution: An optical sensor system is used for the Tape Start and End Sensors on this equipment. Carefully read and follow the instructions below. Otherwise the unit may operate erratically. What to do for preparation Insert a tape into the Deck Mechanism Assembly and press [ B ] (VCR) button.

  • Page 12: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Fig. Loc. Part Removal Note This flowchart indicates the disassembly steps to gain access to items to be serviced. When reassembling, Motor DC follow the steps in reverse order. Bend, route, and D4 2(S-11) dress the cables as they were originally.
  • Page 13 Reference Notes (S-4) 1. Locking Tabs (L-1) and (L-2) are fragile. Be careful [4] Front Bracket not to break them. 1-1. Remove Screw (S-2). (S-4) (S-5) 1-2. Release four Locking Tabs (L-1). Front Support 1-3. Release three Locking Tabs (L-2). (S-4) 1-4.
  • Page 14 : See Reference Note 5. (S-21) [7] Motor DC Fan [8] Rear Panel * (S-20) (S-10) [14] VCR (S-13) Chassis Unit Rear Holder (S-12) Earth Spring (S-11) (S-13) [13] Power SW [6] Fan Holder CN1002 Fig. D4 (S-19) (S-14) FFC Guide Desolder (S-15) CL1001...
  • Page 15 Cylinder Assembly FE Head ACE Head Assembly [15] Deck SW507 Assembly LD-SW [17] Rear Jack [16] DTV Module CBA Unit [18] AV CBA [15] Deck Assembly Cam Gear Hole Shaft Hole (S-22) LD-SW [18] AV CBA [18] AV CBA (S-23) Desolder Desolder From...
  • Page 16 (S-24) [19] Deck Pedestal [21] Bracket R (S-27) [20] Front Bracket R DV Earth Plate (S-25) (S-26) DV Cable Fig. D8 1-6-5 E9TFCDC...
  • Page 17 3. How to Eject Manually Note: When rotating the gear, be careful not to damage the gear. 1. Remove the Top Cover, Front Assembly, Front Bracket, DVD Mechanism & DVD Main CBA Assembly. 2. Remove the Dust Cover. 3. Rotate the gear in the direction of the arrow manually as shown below the tray descends. 4.

  • Page 18: Electrical Adjustment Instructions

    ELECTRICAL ADJUSTMENT INSTRUCTIONS Head Switching Position Adjustment Note: 1. Electrical adjustments are required after replacing Purpose: circuit components and certain mechanical parts. To determine the Head Switching position during It is important to do these adjustments only after playback. all repairs and replacements have been completed.

  • Page 19: How To Initialize The Dvd Recorder & Vcr

    HOW TO INITIALIZE THE DVD RECORDER & VCR To put the program back at the factory-default, initialize the DVD recorder & VCR as the following procedure. < DVD Section > 1. Turn on the DVD recorder & VCR. 2. Confirm that no disc is loaded or that the disc tray is open.

  • Page 20: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE 1. Turn the power on and remove the disc on the tray. 4. Select the firmware version pressing arrow buttons, then press [ENTER/OK]. 2. To put the DVD recorder & VCR into version up Fig. d appears on the screen and Fig. e appears mode, press [DVD], [CM SKIP], [6], [5], and [4] on the VFD.
  • Page 21 How to Verify the Firmware Version 1. Turn on the DVD recorder & VCR. 2. Confirm that no disc is loaded or that the disc tray is open. To put the DVD recorder & VCR into the Version display mode, press [DVD], [CM SKIP], [1], [2], and [3] buttons on the remote control unit in this order.

  • Page 22: Function Indicator Symbols

    FUNCTION INDICATOR SYMBOLS < VCR Section > Note: If a mechanical malfunction occurs, the power is turned off. Turn the power back on by pressing [STANDBY-ON] button and an error message will be displayed on the TV screen for 5 seconds. MODE INDICATOR ACTIVE When reel or capstan mechanism is not...
  • Page 23 < DVD Section > Note: If an error occurs, a message with the error number appears on the screen. Recording Error Error message You cannot record on this disc as Power Calibration Area is full. Error No. Error Message Solution Error Description An error occurs during data reading.
  • Page 24 Error Message Solution Error Description Disc is full. Insert the recordable disc with No available recording space. (No area for new recording) enough recording space. The 99 title limit has been reached. You cannot record more than (Video Format Disc) 99 titles on one disc.

  • Page 25: Troubleshooting

    TROUBLESHOOTING 1 Power Supply Section FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse (F1001) normal? Is normal state restored when once unplugged power Check for leak or short-circuiting of primary circuit cord is plugged again after several seconds? component and service it if defective.
  • Page 26 FLOW CHART NO.6 AL+44V is not outputted. Check D013, D1140 and their periphery, and service Is the supply voltage 44V fed to the cathode of D013? it if defective. Check for short-circuiting or leak on the load circuit, and service it if defective. FLOW CHART NO.7 P-ON+15V is not outputted.
  • Page 27 FLOW CHART NO.11 AL+5V is not outputted. Is the supply voltage 5V fed to the cathode of D016? Check D016, D1102 and their periphery, and service it if defective. Check for short-circuiting or leak on the load circuit, and service it if defective. FLOW CHART NO.12 P-ON+5V is not outputted.
  • Page 28 FLOW CHART NO.15 DVD-P-ON+5V is not outputted. Is the supply voltage 5V fed to the cathode of D016? Check D016, D1102 and their periphery, and service it if defective. Is the "H" pulse (approximately 6V) inputted to Refer to "FLOW CHART NO.16"<P-ON+10V is not the base of Q1106? outputted>.
  • Page 29 FLOW CHART NO.19 P-ON+1.8V is not outputted. Is 3V voltage supplied to Pin(1) of IC1103? Check D1033 and their periphery, and service it if defective. Is the "H" pulse (approximately 1.3V) inputted to Check Q1109, REG-CONT line, and service it if Pin(4) of IC1103? defective.
  • Page 30 2 DVD Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of Re-install the key switches correctly or replace the key switches normal? the defective key switches. Is the control voltage normally inputted into Pin(8) of Check the key switches and their periphery, and service IC501? it if defective.
  • Page 31 FLOW CHART NO.3 There is [No Disc] indication. Both picture and sound do not operate normally. Replace DVD MECHANISM & DVD MAIN CBA ASSEMBLY. FLOW CHART NO.4 VIDEO E-E does not appear normally. Are the video signals inputted to each pin of IC1509? Check the line between video input terminal and each pin of IC1509, and service it if defective.
  • Page 32 Are the video signals outputted to each pin of IC1509? IC1509 30PIN VIDEO-OUT 1 (AV1) Is 5V voltage supplied to Pin(27, 29, 47, 63) of IC1509? IC1509 22PIN VIDEO-OUT 2 (AV2) Is 9V voltage supplied to Pin(75) of IC1509? IC1509 40PIN VIDEO-Y IC1509...
  • Page 33 Are the video signals outputted to the specific output terminal? Check the periphery of JK1504 from Pin (30) of IC1509 Are the composite video signals outputted to and service it if defective. the VIDEO OUT (AV1) terminal (JK1504)? Are the composite video signals outputted to Check the periphery of JK2001 from Pin (22) of IC1509 the VIDEO OUT (AV2) terminal (JK2001)? and service it if defective.
  • Page 34 Are the analog audio signals outputted to each pin of IC1509? Is 5V voltage supplied to Pin(27, 29, 47 ,63) of IC1509? IC1509 73, 74PIN AUDIO-OUT 1 (AV1) Is 9V voltage supplied to Pin(75) of IC1509? IC1509 71, 72PIN AUDIO-OUT 2 (AV2) IC1509 67, 68PIN AUDIO-OUT (REAR) Check the ECO+5V, ECO+9V Replace IC1509.
  • Page 35 3 VCR Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of the Re-install the key switches correctly or replace key switches normal? the defective key switches. Check the key switches and their periphery, and service Is the control voltage normally inputted into Pin(7) of it if defective.
  • Page 36 FLOW CHART NO.3 Cassette tape can not be loaded. Check the line between the start sensor and Pin(100) When loading a cassette tape, on Pin(100) of IC501, of IC501, and service it if defective. does the "L" pulse switch to the "H" pulse? When loading a cassette tape, is the specified voltage Replace the Capstan Motor Unit.
  • Page 37 FLOW CHART NO.6 Capstan Motor does not rotate. Is 5V voltage supplied to Pin(2) of CN502? Check the P-ON+5V line and service it if defective. Is over approximately 2.6V voltage supplied to Pin(5) Check the line between Pin(5) of CN502 and Pin(76) of of CN502? IC501, and service it if defective.
  • Page 38 FLOW CHART NO.10 Video E-E does not appear normally. Are the video signals inputted to each pin of IC1509? Check the line between video input terminal and each pin of IC1509, and service it if defective. IC1509 20PIN VIDEO-IN 1 (AV1) →...
  • Page 39 FLOW CHART NO.11 Hi-Fi E-E audio does not operate normally. Check the line between audio input terminal and each pin of IC1509, and service it if defective. Are the audio signals inputted to each pin of IC1509? → IC1509 84, 85PIN JK1504 AUDIO-IN1 (AV1) IC1509...
  • Page 40 FLOW CHART NO.12 Hi-Fi audio can not be recorded normally. (E-E mode is normal.) Replace IC451. Is the Hi-Fi-COM signal outputted to Pin(26) of IC451? Check the line between Pin(8) of CN251 and Pin(26) Is the line between Pin(8) of CN251 and Pin(26) of of IC451, and service it if defective.

  • Page 41: Block Diagrams

    BLOCK DIAGRAMS Servo/System Control Block Diagram 1-12-1 E9TFABLS...
  • Page 42 Sub System Control Block Diagram E9TFABLSS 1-12-2...
  • Page 43 Digital Signal Process Block Diagram 1-12-3 E9TFABLD...
  • Page 44 Video Selector Block Diagram E9TFABLVS 1-12-4...

  • Page 45: Video Block Diagram

    Video Block Diagram TMDS TRANSMITTER TMDS ENCODER HDCP CIPHER/ ENCRYPTOR CONTROLLER AUDIO TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM 1-12-5 E9TFABLV...
  • Page 46 Audio Selector Block Diagram E9TFABLAS 1-12-6...
  • Page 47 Audio Block Diagram E9TFABLA 1-12-7...
  • Page 48 Hi-Fi Audio Block Diagram 1-12-8 E9TFABLH...
  • Page 49 Power Supply Block Diagram 1-12-9 E9TFABLP...
  • Page 50 Sub Power Supply Block Diagram 1-12-10 E9TFABLSP...
  • Page 51 DTV Module Block Diagram 1-12-11 E9TFABLDTV...

  • Page 52: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 53 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
  • Page 54 AV 1/10 Schematic Diagram < VCR Section > 1-13-3 E9TFASCAV1...
  • Page 55 AV 2/10, Power SW & Sensor Schematic Diagram < VCR Section > FL601 MATRIX CHART BS CS DR DTV BS CS * NOTE These components (IC700, R706,R707) can be used in any models. However, you cannot mix components under Group A with the ones under Group B. You can choose either Group.
  • Page 56 AV 3/10 Schematic Diagram < VCR Section > 1-13-5 E9TFASCAV3...
  • Page 57 AV 4/10 Schematic Diagram < VCR Section > 1-13-6 E9TFASCAV4...
  • Page 58 AV 5/10 Schematic Diagram < VCR Section > 1-13-7 E9TFASCAV5...
  • Page 59 AV 6/10 Schematic Diagram < VCR Section > 1-13-8 E9TFASCAV6...
  • Page 60 AV 7/10 Schematic Diagram < VCR Section > 1-13-9 E9TFASCAV7...
  • Page 61 AV 8/10 Schematic Diagram < VCR Section > E9TFASCAV8 1-13-10...
  • Page 62 AV 9/10 Schematic Diagram < VCR Section > E9TFASCAV9 1-13-11...
  • Page 63 AV 10/10 Schematic Diagram < VCR Section > 1-13-12 E9TFASCAV10...
  • Page 64 Power Supply Schematic Diagram < VCR Section > CAUTION ! CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. For continued protection against fire hazard, The voltage for parts in hot circuit is measured using If Main Fuse (F1001) is blown , check to see that all components in the power supply replace only with the same type fuse.
  • Page 65 Function, SW & USB Schematic Diagram < VCR Section > CAUTION ! For continued protection against fire hazard, replace only with the same type fuse(F6001). NOTE: Either IC3607 or IC3608 is used for FUNCTION CBA. E9TFASCF 1-13-14...
  • Page 66 Rear Jack Schematic Diagram < VCR Section > 1-13-15 E9TFASCRJ...
  • Page 67 DVD Main 1/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-16 E9TFASCD1...
  • Page 68 DVD Main 2/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-17 E9TFASCD2...
  • Page 69 DVD Main 3/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-18 E9TFASCD3...
  • Page 70 DVD Main 4/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-19 E9TFASCD4...
  • Page 71 DVD Main 5/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-20 E9TFASCD5...
  • Page 72 DVD Main 6/7 Schematic Diagram < DVD Section > 1-13-21 E9TFASCD6...
  • Page 73 DVD Main 7/7 Schematic Diagram < DVD Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into six and shown as IC101 (1/6) ~ IC101 (6/6) in this DVD Main Schematic Diagram Section. 1-13-22 E9TFASCD7...
  • Page 74 DTV Module Schematic Diagram < DVD Section > 1-13-23 E9TFASCDTV...
  • Page 75 AV CBA Top View Sensor CBA Top View TO SENSOR CBA JP278 (START-SENSOR) AV CBA S-INH BHF300F01012A Q504 R1648 R1493 JP303 J305 C-POW-SW R1643 R1635 P-ON+44V J343 SPDIF R1666 R1494 JP304 CN1504 J306 R1495 +44V BHF300F01012B +44V J292 CN1503 ALL/SYS+5V R1791 R1667 R1634...
  • Page 76 AV CBA Bottom View WF10 PIN 17 OF PIN 9 OF PIN 7 OF PIN 5 OF PIN 3 OF PIN 28 OF CN1502 CN1502 CN1502 CN1502 CN1502 CN1503 R1648 C-POW-SW R1493 CN1504 R1643 P-ON+44V R1635 +44V R1666 R1494 SPDIF R1495 +44V ALL/SYS+5V...
  • Page 77 Power Supply, Function, SW, Rear Jack, USB & Power SW CBA Top View NOTE: Because a hot chassis ground is present in the power supply CAUTION ! The voltage for parts in hot circuit is measured using circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 78 Power Supply, Function, SW, Rear Jack, USB & Power SW CBA Bottom View NOTE: Because a hot chassis ground is present in the power supply CAUTION ! CAUTION ! The voltage for parts in hot circuit is measured using circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 79 WAVEFORMS NOTE: Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL) Pin 9 of CN1502 Pin 17 of CN1502 Pin 56 of IC301 V-OUT E-E 0.2V 20µs VIDEO-C 0.2V 20µs AUDIO(L)-OUT 0.5ms Pin 56 of IC301 UPPER Pin 30 of IC1509 Pin 28 of CN1503 TP504 WF10...
  • Page 80 WIRING DIAGRAM < VCR SECTION > VIDEO-Y(I)-OUT 1 GND 2 VIDEO-Pb/Cb-OUT 3 GND 4 VIDEO-Pr/Cr-OUT 5 GND 6 VIDEO-Y(I/P)-OUT 7 GND 8 VIDEO-C-OUT 9 GND 10 AUDIO(L)-IN 11 GND 12 AUDIO(R)-IN 13 GND 14 AUDIO(R)-OUT 15 GND 16 AUDIO(L)-OUT 17 DVD-AUDIO-MUTE 18 AUDIO+5V 19 VIDEO-Y/CVBS-IN 20...
  • Page 81 WIRING DIAGRAM < DVD SECTION > DTV-SYS-RESET DTV-TXD DTV-RXD DTV-S-SCLK(NU) BOOTSTRAP(NU) V-BUS DVD/CD LASER DIODE DRIVE E9TFAWID 1-15-2...

  • Page 82: Ic Pin Function Descriptions

    IC PIN FUNCTION DESCRIPTIONS < VCR Section > Signal Function Name IC501 ( MICROCONTROLLER 8BIT SERVO VCR- VCR Audio Mute Control / SYSTEM CONTROL ) 27 OUT AUDIO- Signal (Mute=“L”) MUTE Signal Function Name IN A-MODE Hi-Fi Tape Defection Signal Input Signal from Pin 8 of IN SC2-IN DVD-...
  • Page 83 Signal Signal Function Function Name Name IN DAVN-L VPS/PDC Data (Receive=“L”) IN VCR-POW- VCR P-ON Power Defection SAFETY Input Signal Ground Capstan Motor Rotation IN C-FG Composite Synchronized Detection Pulse IN C-SYNC Pulse AMPVss Ground 59 OUT POW-SW Power Switching Signal Ground 60 OUT REG- Power Regulator Control...
  • Page 84 IC612 ( VFD DRIVER ) Signal Function Name Signal Function Name Ground POWER- POWER-LED Control Signal OUT DVD-LED DVD-LED Control Signal OUT VCR-LED VCR-LED Control Signal Not Used IN OSC Oscillator Input Not Used IN DRV-DIN Serial Data Input IN DRV-CLK Serial Clock Input IN DRV-STB Serial Interface Input...

  • Page 85: Lead Identifications

    LEAD IDENTIFICATIONS MMBTRC103SS STD1862LY-AT KTA1281-Y-AT/P 2SA1980MG-AT 2SA1266G MMBTSC3875G SRC1203MAT 2SA1980G MMBTSC3875Y 2SC3198(G, L) RA103S 2SC5343G-AT RA104S 2SC5344 Y RC103S E C B E C B E C B E C B UTC0832 AK4141EQP-8 2SK3566(STA4 Q M) AS431BZTR-E1 PQ070XFC1SZF KTC2026-Y/P R A K 1 2 3 4 G D S B C E...

  • Page 86: Exploded Views

    EXPLODED VIEWS Cabinet See Electrical Parts List for parts with this mark. TU1800 Rear Jack CBA DTV Module CBA Unit DVD Mechanism & DVD Main CBA Unit Sensor CBA AV CBA FM1001 Power Supply CBA AC1001 Function CBA F1001 Power SW CBA SW CBA USB CBA 1-18-1...
  • Page 87 Packing Outside Inside Inside Outside FRONT 1-18-2 E9TFAPEX...

  • Page 88: Mechanical Parts List

    MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. ! have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read REMOTE CONTROL UNIT NB848EH NB848EH carefully the product safety notice in this service X2A! OWNERS MANUAL(EN) E9TFAED 1VMN33273...

  • Page 89: Electrical Parts List

    ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. ! have special characteristics important to safety. C331 ELECTROLYTIC CAP . 220F/6.3V M H7 CEB221TSK028 Before replacing any of these components, read C332 ELECTROLYTIC CAP . 100F/16V M H7 CED101TSK028 carefully the product safety notice in this service C333...
  • Page 90 Ref. No. Description Part No. Ref. No. Description Part No. C469 ELECTROLYTIC CAP . 22F/10V M H7 CEC220TSK028 C703 CHIP CERAMIC CAP .(1608) B K 0.01F/50V CHD1JK30B103 C470 CHIP CERAMIC CAP .(1608) B K 4700pF/50V CHD1JK30B472 C704 ELECTROLYTIC CAP . 47F/6.3V M H7 CEB470TSK031 C471 CHIP CERAMIC CAP .(1608) B K 0.01F/50V...
  • Page 91 Ref. No. Description Part No. Ref. No. Description Part No. C1618 CHIP CERAMIC CAP .(1608) F Z 0.1F/50V CHD1JZ30F104 C1826 CHIP CERAMIC CAP .(1608) CH D 10pF/50V CHD1JD3CH100 C1619 CHIP CERAMIC CAP .(1608) F Z 0.1F/50V CHD1JZ30F104 C1901 CHIP CERAMIC CAP . B K 0.68F/10V CHD1AK30B684 C1620 CHIP CERAMIC CAP .(1608) F Z 0.1F/50V...
  • Page 92 Ref. No. Description Part No. Ref. No. Description Part No. D1544 DIODE ZENER 11BSA-T26 NDTA011BST26 L1601 BEAD CORE ASSEMBLY E3TK3FD 1VSA22787 D1545 DIODE ZENER 11BSA-T26 NDTA011BST26 L1802 CHIP INDUCTOR LK16081R8K-T 1.8UH LLACKB3TU1R8 D1547 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F L1803 CHIP INDUCTOR LK16081R8K-T 1.8UH LLACKB3TU1R8 D1548 DIODE SWITCHING 1N4148-F0021...
  • Page 93 Ref. No. Description Part No. Ref. No. Description Part No. R324 RES CHIP 1608 1/10W J 3.3 k RRXA332HH013 R528 RES CARBON FILM 1/4W G 4.7 k RCG472PAK001 R325 RES CHIP 1608 1/10W J 1.2 k RRXA122HH013 R536 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013 RES CHIP 1608 1/10W J 680 ...
  • Page 94 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 820  R709 RES CHIP 1608 1/10W J 10 k RRXA103HH013 R1706 RRXA821HH013 RES CARBON FILM 1/4W J 75  R1493 RES CARBON FILM 1/4W J 1.5 k RCJ152PAK001 R1708 RCJ750PAK001...
  • Page 95 Ref. No. Description Part No. Ref. No. Description Part No. R1808 RES CHIP 1608 1/10W F 10.0 k RTW1002HH008 JP361 WIRE CP STP-S-0.60 XZ40F0REN002 R1809 RES CHIP 1608 1/10W F 4.70 k RTW4701HH008 SCREW P-TIGHT M3X8 BIND HEAD+ GBCP3080 R1811 RES CHIP 1608 1/10W J 3.3 k...
  • Page 96 Ref. No. Description Part No. Ref. No. Description Part No. C1034 CAP POLYESTER FILM 0.0033F/100V J CA2A332SER02 D1059 RECTIFIER DIODE BA159 NDQZ000BA159 C1035 ELECTROLYTIC CAP . 3300F/6.3V CE0KMASDL332 D1061 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST C1036 CERAMIC CAP . B K 1000pF/1KV CCG102PAN001 D1062 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST...
  • Page 97 Ref. No. Description Part No. Ref. No. Description Part No. Q1109 NPN TRANSISTOR RES-IN SRC1203MAT NQSZSRC1203M R1187 RES CHIP 1608 1/10W F 100 k RTW1003HH008 CARBON RES. 1/4W J 820  Q1112 NPN TRANSISTOR 2SC5344 Y NQSY02SC5344 R1190 RCX4JATZ0821 RES CHIP 1608 1/10W 0  Q1114 PNP TRANSISTOR 2SA1980MG-AT NQSG2SA1980M...
  • Page 98 SW CBA USB CBA Ref. No. Description Part No. Ref. No. Description Part No. SWC1 SW CBA (PW/SW-C) ---------- USB1 USB CBA (PW/SW-E) ---------- Consists of the following: Consists of the following: RESISTORS CONNECTORS R3020 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013 CN6001 PH CONNECTOR SIDE 4P S4B-PH-K-...
  • Page 99 WD6D-M100 E9TFAEH 2013-12-20 Ver.1...

Table of Contents