Beep Function - Kenwood TS-590SG Instruction Manual

12 OPERATOR CONVENIENCES
The table below is an example of setting the Auto
Mode frequency.
Channel Frequency
No. (MHz)
00 1.620 AM
01 2.000 CW
02 3.500 LSB
03 3.525 CW
04 10.100 LSB
05 10.150 CW
06 14.000 USB
14.070 CW-R 14.000  f < 14.070
07
08 14.112 FSK
09 18.068 USB
10 18.110 CW
11 21.000 USB
12 21.070 CW
21.125 FSK-R 21.070  f < 21.125
13
14 21.150 CW
15 24.890 USB
16 24.930 CW
17 28.000 USB
18 28.070 CW
19 28.150 FSK
20 28.200 CW
21 29.000 USB
30.000 FM-DATA 29.000  f < 30.000
22
23 50.000 USB
24 50.100 CW
25 51.000 USB
26 52.000 FM
27 52.000 LSB
28 52.000 LSB
29 52.000 LSB
30 52.000 LSB
31 52.000 LSB
• The frequencies for channels 27 ~ 31 have not
been confi gured, but because they are the same
frequency as channel 26, they will be FM mode
51.0 MHz  f < 52.0 MHz.
• Since the frequencies above 52.0 MHz have not
been confi gured, they will be USB mode
52.0 MHz  f < 60.0 MHz
54
Operation Range
Mode
(MHz)
0.030  f <
1.620
1.620  f <
2.000
2.000  f <
3.500
3.500  f <
3.525
3.525  f < 10.100
10.100  f < 10.150
10.150  f < 14.000
14.070  f < 14.112
14.112  f < 18.068
18.068  f < 18.110
18.110  f < 21.000
21.000  f < 21.070
21.125  f < 21.150
21.150  f < 24.890
24.890  f < 24.930
24.930  f < 28.000
28.000  f < 28.070
28.070  f < 28.150
28.150  f < 28.200
28.200  f < 29.000
30.000  f < 50.000
50.000  f < 50.100
50.100  f < 51.000
51.000  f < 52.000

BEEP FUNCTION

The Beep function provides you confi rmation of entry,
error status, and malfunctions of the transceiver.
Although you can turn the beep function OFF by
accessing Menu No. 05, we recommend you leave
it ON in order to detect unexpected errors and
malfunctions. You can also change the output level of
the beeps by accessing Menu No. 05 and selecting "1"
to "20".
The transceiver generates the following Morse code
to tell you which mode is selected when you change
operating modes:
Mode
USB
LSB
CW
FSK
AM
FM
USB-DATA
LSB-DATA
CW-R
FSK-R
AM-DATA
FM-NAR
FM-DATA
FM-NAR-DATA
The transceiver also generates the following warning,
confi rmation, and malfunction beeps.
Beep Type
Short, high pitch A valid key is pressed.
Double, high pitch A secondary function is selected.
3 times, high pitch The third function is accepted.
A key entry is accepted, Scan
Long, high pitch
starts, or AT tune has completed.
Short, regular A function is turned OFF.
Short, low pitch An invalid key is pressed.
The internal PLL circuit unlock
Morse "UL"
status is detected.
CW Auto Tune cannot complete,
Morse "S"
or an invalid frequency is entered.
AT Tune cannot be completed
Morse "5"
within the specifi ed time.
The antenna's SWR is too high
Morse "SWR"
(over 10:1) to perform AT tune.
1 minute before the APO (Auto
Power Off) function switches the
Morse "CHECK" transceiver OFF, a protection
circuit is ON. or an invalid
voltage is detected.
Waiting for a CW message to be
Morse "BT"
recorded.
Morse Code Output
• • –
(U)
• – • •
(L)
– • – •
(C)
• – •
(R)
• –
(A)
• • – •
(F)
• • – – • •
(UD)
• – • • – • •
(LD)
– • – • • – •
(CR)
• – • • – •
(RR)
• – – • •
(AD)
• • – • – •
(FN)
• • – • – • •
(FD)
• • – • – • – • •
(FND)
Meaning