Storing Frequency Ranges - Kenwood TS-590SG Instruction Manual

1 Recall the desired memory channel.
2 Press [M.IN] to enter Memory Scroll mode.
• To exit Memory Scroll mode, press [CLR].
3 Select the memory channel where you would
like the data copied, using the MULTI/CH
control.
4 Press [M.IN].
Channel 00 ~ 99
Channel E0 ~ E9
RX frequency
TX frequency
Mode for RX
Mode for TX
Tone frequency
CTCSS frequency
Tone/ CTCSS
ON/ OFF status
Memory Name
Memory Channel
Lockout ON/ OFF
Filter A/ B status
Channel 00 ~ 99
Channel E0 ~ E9
RX frequency
Mode for RX
TX frequency
Mode for TX
Tone frequency
CTCSS frequency
Tone/ CTCSS/ Cross
tone ON/ OFF status
Memory Name
Memory Channel
Lockout ON/ OFF
Filter A/ B status
Channel P0 ~ P9
TX/RX frequency
Mode for TX/RX
Start frequency
End frequency
Tone frequency
CTCSS frequency
Tone/ CTCSS/ Cross
tone ON/ OFF status
Channel 00 ~ 99
➡
Channel E0 ~ E9
➡
RX frequency
➡
TX frequency
➡
Mode for RX
➡
Mode for TX
➡
Tone frequency
➡
CTCSS frequency
Tone/ CTCSS
➡
ON/ OFF status
➡
Memory Name
Memory Channel
➡
Lockout OFF
➡
Filter A/ B status
➡
Channel P0 ~ P9
➡
TX/RX frequency
➡
Start frequency
➡
End frequency
➡
Mode for TX/RX
➡
––
➡
––
➡
Tone frequency
➡
CTCSS frequency
Tone/ CTCSS/ Cross
➡
tone ON/ OFF status
➡
Memory Name
Memory Channel
➡
Lockout OFF
➡
Filter A/ B status
➡
Channel 00 ~ 99
➡
RX frequency
➡
TX frequency
➡
Mode for RX
➡
Mode for TX
➡
––
➡
––
➡
Tone frequency
➡
CTCSS frequency
Tone/ CTCSS/ Cross
➡
tone ON/ OFF status
Channel P0 ~ P9
Memory Name
Memory Channel
Lockout ON/ OFF
Filter A/ B status
Channel P0 ~ P9
TX/RX frequency
Start frequency
End frequency
Mode for TX/RX
Tone frequency
CTCSS frequency
Tone/ CTCSS/ Cross
tone ON/ OFF status
Memory Name
Memory Channel
Lockout ON/ OFF
Filter A/ B status
Note: After copying, the Memory Channel Lockout turns OFF.

STORING FREQUENCY RANGES

Memory channels P0 to P9 allow you to store
frequency ranges for VFO tuning and Program Scan.
Program Scan is described in the next chapter. To
tune or scan frequencies within a specifi ed range,
store the start and end frequencies for that range in
advance.
1 Press [A/B (A=B)] to select VFO A or VFO B.
2 Select the desired start frequency.
3 Press [M.IN] to enter Memory Scroll mode.
• To exit Memory Scroll mode and abort the
storage process, press [CLR].
4 Turn the MULTI/CH control, or press Mic [UP]/
[DWN] to select a memory channel in the range of
P0 to P9.
5 Press [M.IN] to store the start frequency in the
memory channel.
• "ENDINPUT" appears on the sub-display.
6 Turn the Tuning control or MULTI/CH control to
select the end frequency.
7 Press [M.IN] to store the end frequency in the
memory channel.
• The previous data stored in the channel is
overwritten.
MEMORY FEATURES 10
➡
Channel 00 ~ 99
➡
Memory Name
Memory Channel
➡
Lockout OFF
➡
Filter A/ B status
➡
Channel P0 ~ P9
➡
TX/RX frequency
➡
Start frequency
➡
End frequency
➡
Mode for TX/RX
➡
Tone frequency
➡
CTCSS frequency
Tone/ CTCSS/ Cross
➡
tone ON/ OFF status
➡
Memory Name
Memory Channel
➡
Lockout OFF
➡
Filter A/ B status
45