Kenwood TS-590SG Instruction Manual page 72

12 OPERATOR CONVENIENCES
Operation
Memory scan group
setup
Program/VFO scanning
section setup
VOX gain level setup
Speech processor input
level setup
Speech processor
output level setup
Noise Blanker "1" or "2"
level setup
Mic Gain adjustment
Keying Speed selection
TX power adjustment
VOX Delay time setup
Break-in Delay time
setup
TX Monitor volume
adjustment
Carrier level adjustment
AGC constant time AGC
setting (FAST)
AGC constant time AGC
setting (SLOW)
While in Menu mode
While in transmission
output power adjusting
mode for TX Tune
While in threshold level
adjustment mode for the
CW Morse decoder
1
During continuous operation, only the setting value is
announced.
64
Announcement
"Memory scan group" +
Group No. + "Off/On"
• When selecting a
group number, the
group number and "Off/
On" is announced.
• When the settings are
changed, only "Off/On"
is announced.
"VFO" + "Scan" + "Group"
+ Section defi ned No. +
"Off/On"
• When selecting the
section defi ned number,
the section defi ned
number and "Off/On" is
announced.
• When the settings are
changed, only "Off/On"
is announced.
"VOX gain" + Setting
1
value
"Processor in" + Setting
1
value
"Processor out" + Setting
1
value
"Noise blanker" "1" or "2" +
1
Setting value
"Mic gain" + Setting
1
value
"Keying Speed" + Setting
1
value
"TX power" + Setting
1
value
"VOX delay" + Setting
1
value
"Break-in delay" + Setting
1
value
"TX monitor" + Setting
1
value
"Carrier" + Setting value
1
"Fast" + Setting value
1
"Slow" + Setting value
"Menu" + Menu number +
1
Setting value
"T" + "Power" + Setting
1
value
"CW" + "THR" + Setting
1
value
Status Settings using VOICE1
Status
Press [ ]
While in VFO mode
Press [A/B (A=B)]
Changing VFO A or B
while in VFO mode
(TF-SET ON/OFF is
stored)
Press [1.8] ~ [50] or
[GENE]
Press [LSB/USB]/ [CW/
FSK (REV)]/ [FM/AM
(FM-N)]
Changing the frequency
while in VFO mode
Changing the mode
while in VFO mode
Press [M/V]
While in Memory
channel mode
Turn the MULTI/CH
control
Changing the memory
channel while in Memory
channel mode
Changing the mode
while in Memory channel
mode
Hold or Release [TF-
SET]
TF-SET ON/OFF while in
Memory scroll mode
Editing the channel
name
(While in character
selection)
Press [Q-MR]
While in Quick memory
1
mode
Turn the MULTI/CH
control
Changing the memory
channel while in Quick
memory mode
Press [M.IN]
While in Memory scroll
mode
Announcement
1
"VFO" + ("S" +) "A/B" +
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
1
("S" +) "A/B" +
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
• Announces when
Menu No. 11 is "1" or "2"
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
• Announces when
Menu No. 11 is "1" or "2"
"Channel" + Channel
1
number + ("S" +)
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
Channel number +
1
("S" +) Frequency
• Announces when
Menu No. 11 is "1" or "2"
1
("S" +) Frequency (+
"X/R/XR" + RIT/XIT
4
Frequency)
• Announces when
Menu No. 11 is "1" or "2"
Selected character
or symbol. ("@", "/"
and "Space" are not
announced.)
"Quick memory" +
Channel number +
1
("S" +) "A/B" +
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
Channel number +
1
("S" +) "A/B" +
Frequency (+ "X/R/XR" +
4
RIT/XIT Frequency)
• Announces when
Menu No. 11 is "1" or "2"
Empty Channel:
"Memory in" + Channel
number + "Blank"
Stored Channel:
Channel number +
1
("S" +) Frequency