Accessories - Lincoln Electric INVERTEC V205-T DC Operator's Manual

V205-T DC & V205-T AC/DC
GENERAL OPTIONS /

ACCESSORIES

Factory Installed
Twist-Mate Cable Connectors
1 – standard for Ground Clamp
1 – Gas Pass through for Tig Torch
Strap Packet
Instruction Manual
Field Installed
K857 - Remote Output Control - For Stick welding. When the
V205-T's Output Control is in the "REMOTE" position, this portable
current control provides the same range as the current control on
the welder. Consists of a 6-pin Amphenol connector which plugs
into the remote control Amphenol. 25 foot cable length.
K870 - Foot Amptrol tm for TIG welding. When the V205-T's Output
Control is in the "REMOTE" position, the foot Amptrol energizes
the output and controls the output remotely. The Foot Amptrol
connects directly to the 6 pin Amphenol.
K963-3 - Hand Amptrol tm for TIG welding. When the V205-T's
Output Control is in the "Remote" position, the hand Amptrol
energizes the output and controls the output remotely. The Hand
Amptrol connects directly to the 6 pin Amphenol.
K814 - Arc Start Switch - Energizes the output for TIG welding if
remote output control of the amperage is not desired. It allows
on/off TIG welding at the current set by the Current Control on the
control panel. When using the Arc Start Switch set the Output
Control to the "LOCAL" position.
Magnum® PTA-9 and PTA-17 TIG Torches - The following stan-
dard Magnum® TIG torches with one-piece cable may be used with
the Invertec V205-T.
• K1781-1 PTA-9 12.5 ft
• K1781-3 PTA-9 25 ft
• K1782-1 PTA-17 12.5 ft
• K1782-3 PTA-17 25 ft
NOTE: Each torch requires a Twist-Mate™ adapter, (one is includ-
ed with the machine). Collets, collet bodies, and nozzles are not
included and must be ordered separately.
medium back cap
medium back cap
long back cap
long back cap
C 1
TIG TORCH KITS
K2266-1 – TIG-Mate 17 Air Cooled TIG Torch Starter Pack.
One complete easy-to-order kit packaged in its own portable car-
rying case. Includes: PTA-17 torch, parts kit, Harris
flowmeter/regulator, 10 ft. gas hose, Twist-Mate™ adapter, work
clamp and cable.
K2267-1 – TIG-Mate 20 Water-Cooled TIG Torch Starter Pack.
One complete easy-to-order kit packaged in its own portable car-
rying case. Includes: PTW-20 torch, parts kit, Harris
flowmeter/regulator, 10 ft. gas hose, Twist-Mate™ adapter, work
clamp and cable, and 10 ft. water hose.
CABLE PLUGS
K852-70 - Cable Plug Kit for 1/0-2/0 cable. Attaches to welding
cable to provide quick disconnect from machine.
Twist-Mate Torch Adapter K1622-1 - One is shipped with the
welder torch. If you do not care to interchange this part between
torches (one is required to connect Magnum PTA-9 or PTA-17 TIG
torches with one-piece cable to the V205-T) you may order an addi-
tional adapters. The quick connect plug provides connection for
both gas and welding current.
K1622-4 – Twist-Mate adapter for Water-Cooled TIG torches.
Adapter for PTW-18 and -20 Torches.
TIG Torch Parts Kits - Parts kits are available for the PTA-9 and
PTA-17 TIG torches. These kits include back cap, collets, collet
bodies, nozzles and tungstens.
Order KP507 for PTA-9 torches
Order KP508 for PTA-17 torches
Order KP2414-1 Gas Lens Parts kit for PTA-9 torches
See publication E12.150 for parts kits breakdown.
Cut Length Consumables - TIG welding filler metals are available
for welding stainless steel, mild steel, aluminum and copper
alloys. See publication C9.10.
ACCESSORIES