Adjusting The Speaker Output Levels - Yamaha HTR-5490 Owner's Manual

· ADJUSTING THE SPEAKER OUTPUT LEVELS
AMP
~
1
3
3
TEST
~
Use the test tone to balance the output levels of the 6
speakers required for a surround sound system. The
adjustment of each speaker output level should be made at
your listening position with the remote control. After
completing the adjustments, use VOL
+/-
at your
listening position to check if the adjustments are
satisfactory.
4
2,5
6
Press TEST to output the test tone.
o
Press AMP to select the
AMP mode.
AMP appears in the display
window on the remote control.
3
SPEAKERS
A B
~Q.-\.
Turn on the video monitor connected to this
unit.
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of the
main speakers, press both A
andB.
2 3
Set the BASS and TREBLE controls on the
front panel to the center position and turn off
BASS EXTENSION and PROCESSOR
DIRECT by pressing the buttons.
"BASS EXT. OFF" and "P. DIRECT OFF" appear
on the front panel display.
• Since this unit canNot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.
This section explains how to adjust the speaker output
levels by using the test tone generator. When this
adjustment is made, the output level heard at the listening
position will be the same from each speaker. This is
important for the best performance of the digital sound
field processor, and various decoders (Dolby Digital,
Dolby Pro Logic, Dolby Pro Logic II, DTS, DTS ES, and
DTS Neo: 6).
Adjust the volume of this unit so you can
hear the test tone.
BASS TREBLE
.<rD. .(IT)
+ +
BASS PROCESSOR
EXTENSION DIRECT
~q
. . . -\.
Set to OFF.
VOLUME
(0)
Front panel
or
+
VOL
Remote control
23
· ADJUSTING THE SPEAKER OUTPUT LEVELS
AMP
~
1
3
3
TEST
~
Use the test tone to balance the output levels of the 6
speakers required for a surround sound system. The
adjustment of each speaker output level should be made at
your listening position with the remote control. After
completing the adjustments, use VOL
+/-
at your
listening position to check if the adjustments are
satisfactory.
4
2,5
6
Press TEST to output the test tone.
o
Press AMP to select the
AMP mode.
AMP appears in the display
window on the remote control.
3
SPEAKERS
A B
~Q.-\.
Turn on the video monitor connected to this
unit.
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of the
main speakers, press both A
andB.
2 3
Set the BASS and TREBLE controls on the
front panel to the center position and turn off
BASS EXTENSION and PROCESSOR
DIRECT by pressing the buttons.
"BASS EXT. OFF" and "P. DIRECT OFF" appear
on the front panel display.
• Since this unit canNot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.
This section explains how to adjust the speaker output
levels by using the test tone generator. When this
adjustment is made, the output level heard at the listening
position will be the same from each speaker. This is
important for the best performance of the digital sound
field processor, and various decoders (Dolby Digital,
Dolby Pro Logic, Dolby Pro Logic II, DTS, DTS ES, and
DTS Neo: 6).
Adjust the volume of this unit so you can
hear the test tone.
BASS TREBLE
.<rD. .(IT)
+ +
BASS PROCESSOR
EXTENSION DIRECT
~q
. . . -\.
Set to OFF.
VOLUME
(0)
Front panel
or
+
VOL
Remote control
23