Loading Factory Defaults; Enrolling Modules And Keypads; Control Panel Programming Locations - GE NetworX NX-6 Installation And Startup

Networx series

Hide thumbs Also See for NetworX NX-6:

User manual (20 pages)

Table Of Contents

Table of Contents

FEATURE SELECTION DATA

Feature selection data will display the current condition (on or off) of eight features associated with the programming

location and segment selected. Pressing a button on the touchpad (1 thru 8) that corresponds to the "feature number"

within a segment will toggle (on/off) that feature. Pressing any numeric key between [1] and [8] for selection of a

feature, will make the corresponding LED illuminate (feature ON). Press the number again, and the LED will extinguish

(feature OFF). You will see that numerous features can be selected from within one segment. For instance, if all eight

features of a segment are desired, pressing [1]-[2]-[3]-[4]-[5]-[6]-[7]-[8] will turn on LED's 1 thru 8 as you press the

keys, indicating that those features are enabled. LCD Keypad Users Note: The numbers of the enabled features

will be displayed. However, the features not enabled will display a hyphen (-). After the desired setting of

features is selected for this segment, press the [r] key. This will enter the data and automatically advance to the next

segment of the location. When you are in the last segment of a location and press the [r] to enter the data, you will exit

that location. This will now turn the "Ready" LED off and the "Armed" LED on. As before, you are now ready to enter

another programming location.

To load the factory defaults, enter the program mode using the procedure on page 10, then type [9]-[1]-[0]-[#]. The

keypad will beep 3 times indicating that the loading is in progress. The loading takes about 6 seconds.

For supervision purposes, the NX-6 has the ability to automatically find and store in its memory, the presence of all

keypads, zone expanders, wireless receivers, and any other module connected to the data terminal. This allows these

modules to be supervised by the control panel. To enroll the modules, enter the Program Mode of the NX-6 control panel

as described on page 10. When the Program Mode is exited, the NX-6 control will automatically enroll the devices. The

enrolling process takes about 12 seconds, during which time the "Service" LED will illuminate. User codes will not be

accepted during the enrolling process. If a speaker is attached to the NX-6, it will click at this time. If a siren or bell is

attached to the NX-6, it will sound for about 1 second. Once a module is enrolled, if it is not detected by the control, the

"Service" LED will illuminate.

(Various locations intentionally omitted. Attempts to access these reserved locations will cause the

LOCATION 0

PROGRAMMING PHONE #1

The first telephone number is programmed in location 0. A "14" indicates the end of the phone number. Delays of 4

seconds can be programmed at any point in the phone number by programming a "13" in the appropriate segment. If

tone dialing is desired, program a "15" in the segment where tone dialing should begin. If the entire number should be

tone dialing, program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@. Caution: A call-waiting

cancel on a non- call waiting line will prevent successful connection to the central station.

LOCATION 1

ACCOUNT CODE FOR THE PHONE #1

The account code sent when Phone #1 is dialed is programmed in location 1. Program a A10" in the segment immediately

after the last digit of the account code.

LOCATION 2

COMMUNICATOR FORMAT FOR PHONE #1

Location 2 contains the communicator format used to transmit to the receiver connected to Phone #1. Consult the

instructions for your central station receiver to determine which format is compatible. Select a format from the list on

the following page. If you require a format other than those listed, review the override options described in location 18,

to build the appropriate format. A "15" must be programmed in location 2 in addition to the entries in location 18 in

order to create a special format. If this location contains a "0", the built-in communicator will be disabled, and the NX-6

will function as a local only control.

Page 12