GE NetworX Series Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Control Unit
  5. NetworX Series
  6. Manual

GE NetworX Series Manual

Operator
Hide thumbs Also See for NetworX Series:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for GE NetworX Series

Summary of Contents for GE NetworX Series

  • Page 2 THE “OPERATOR” INTRODUCTION ACCESSING YOUR SYSTEM FUNCTIONS OF THE "OPERATOR" ECTION HECKING YSTEM TATUS ECTION SING THE III. ECTION RMING ECURITY YSTEM ECTION SING NSTANT ELAY PTION ECTION ISARMING ECURITY YSTEM ECTION YPASSING ONES VII. ECTION CCESSING TATUS VIII. A ECTION CCESSING THE ONTROL...

  • Page 3: Accessing Your System

    INTRODUCTION The “Operator” is an interactive phone module for Caddx security controls that interconnects your telephone with your security system. It allows authorized users to operate the security system from any TouchTone telephone, whether it is at the protected site or anywhere else in the world.

  • Page 4: Checking System Status

    From an off-site premise, you can also access the “Operator” using a TouchTone telephone. Step 1 Call the phone number of the protected site. Step 2 When the phone is answered, press the pound key three times within the first 8 seconds. If a person or a device such as a fax/answering machine answers the call, the “Operator”...

  • Page 5: Using The Menu

    ρ # "TO ACCESS MENU, ENTER [ ]" - This takes you to the MENU for the other options. # "ZONE BYPASS ACTIVE" - One or more zones are bypassed. Check zone status. ρ # “SYSTEM TROUBLE, ENTER [ ] [2]” – This will identify the service condition.
  • Page 6 # "TO CHANGE CODE, ENTER [5]" – To change a user code. This option available in disarmed state only. Refer to page 13. # “FOR HOME CONTROL MENU, ENTER [6]” – To access menu for lights and thermostat control. Refer to page 9. # “TO RESET SMOKE DETECTOR, ENTER [7]”...

  • Page 7: Disarming Your Security System

    ρ 3 Or to change the armed status to INSTANT, press again. Step 4 “SYSTEM IS ARMED IN STAY MODE. ENTER CODE TO DISARM. EXIT DOOR DELAY IS OFF.” Your system is now armed in the INSTANT mode with no exit delay.
  • Page 8 Step 3 You may toggle (reverse) the bypass condition of a particular zone. After that zone number is stated, press Step 4 The “Operator” will say "PLEASE WAIT" before repeating the status of that zone, and continue scrolling through the remaining zones. Step 5 Press a zone number followed by # to proceed directly to that zone number.
  • Page 9 Section VIII. CCESSING THE ONTROL The Home Control Menu section provides information concerning the lights and temperature control provided through your security system. HOME CONTROL – LIGHTS/APPLIANCES When the “Operator” is on the line, perform the following steps to turn lights/appliances on or off.
  • Page 10 HOME CONTROL – THERMOSTAT CONTROL When the “Operator” is on the line, perform the following steps to change the thermostat control. The thermostat control has three separate modes: Thermostat mode Fan mode Day mode (NOTE: The “Operator” will only function with a special type of thermostat, which may not be currently available in your area.
  • Page 11 Step 4 If you selected the change mode for any of the last four items mentioned in Step 2, the “Operator” will prompt: “ENTER NEW SET POINT FOLLOWED BY [#] ” Step 5 The “Operator” will then repeat the mode with the changes, and continue with the options.
  • Page 12 When the “Operator” is on the line, perform the following steps to set the TIME. Step 1 Press ρ The [ρ] accesses the MENU and [9] proceeds to the OPTIONS menu, then [7] proceeds to the TIME section. Step 2 “PLEASE ENTER YOUR CODE.”...
  • Page 13 PROGRAMMING/CHANGING ACCESS CODES Your security system can be armed and disarmed through the “Operator” by the Master code or the auxiliary codes. Refer to your security system user's manual for the number of codes available in your system. The Code Change section of the MENU is accessed in the DISARMED state.
  • Page 14 ACTIVATING EMERGENCY ALARMS IMPORTANT NOTICE: In order to activate an EMERGENCY alarm through the “Operator”, the telephone you are using MUST hold a continuous audible tone while the button is held down. See page 15 of this booklet or check with your installing company to see if these EMERGENCY activations have been programmed into your security system.

  • Page 15: Zone Descriptions

    Installing/Service Company _________________________________ For Service Call __________________________________________ Central Station ___________________________________________ EMERGENCY ACTIVATION KEYS (check if enabled) Press and hold the key for 2 full seconds. Fire [1] Auxiliary Emergency [2] Police [3] # of Rings To Answer _______ ZONE DESCRIPTIONS 01 _________________________ 17 _________________________ 02 _________________________...

  • Page 16: System Notes

    SYSTEM NOTES...

  • Page 17: Quick Reference

    NETWORX NX540E “OPERATOR” NETWORX NX540E “OPERATOR” ρ ρ ρ TO ACCESS “OPERATOR” ρ ρ ρ TO ACCESS “OPERATOR” ρ MENU ρ MENU ρ 0 ZONE STATUS ρ 0 ZONE STATUS ρ 1 CHANGE AREA ρ 1 CHANGE AREA ρ 2 SYSTEM STATUS ρ...

This manual is also suitable for:

Networx nx-540e

Table of Contents