Default Values ........................12 Compliance ......................... 13 Laser Safety Compliance ..................13 LED CLASS ........................ 14 CE Compliance ......................14 FCC Compliance ..................... 14 Power Supply ......................14 Wasp Barcode Technologies Limited Factory Warranty ......15 Service and Support ......................16...
Contactez le support technique WASP. Die neuesten Treiber und Dokumentation Updates für dieses Produkt verfügbar sind. Kontakt WASP Technical Support. Los últimos controladores y actualizaciones de la documentación para este producto están disponibles. Póngase en contacto con soporte técnico de WASP. Quick Reference Guide...
Aiming System The WLS8600 provides an aiming system. If enabled, a partial trigger press pro- duces a red spot, which should be aimed over the code center to get the best reading performance, see figure (1) above. By completely pressing the trigger the scan line appears to start code scanning (2).
Setting Up the Reader Setting Up the Reader Follow the steps below to connect and get your reader up and communicating with its host. Connect the Cable to the reader and the Host. Configure the Interface (see page 5). Program the Reader starting on page 10 (optional, as needed). Connecting the Cable A.
Ì$+UA04$-@Î USB-COM* Ì$+UA02$-4Î USB-IBM-Hand Held Ì$+UA01$-.Î USB-IBM Table top Ì$+UA00$-(Î USB KBD-APPLE Ì$+UA05$-FÎ * When configuring USB-COM, the relevant files and drivers must be installed from the USB Device Installation software. Contact Wasp Technical Support for information. Quick Reference Guide...
Page 10
Ì$+CP505$-ÈÎ PC Notebook - ALT mode Ì$+CP508$-2Î IBM AT - ALT mode Ì$+CP507$-+Î The Interface for IBM XT and IBM Terminals 3151, 347X and 348X can be se- lected from the WLS8600 Reference Manual available online at www.waspbar- code.com WLS8600...
Selecting the Interface Type Keyboard Nationality USB-KBD and Wedge users should select one of the following wedge keyboard na- tionality codes according to the keyboard. Belge Ì$+FJ7$-8Î Deutsch Ì$+FJ3$-$Î English Ì$+FJ4$-)Î Español Ì$+FJ6$-3Î Français Ì$+FJ2$-ÊÎ Italiano Ì$+FJ1$-ÅÎ Svenskt Ì$+FJ5$-.Î USA (Default) Ì$+FJ0$-|Î...
Page 12
Selecting the Interface Type Keyboard Nationality (continued) The following Keyboard Nationality selections are only valid for IBM AT compat- ible PCs: Japanese Ì$+FJ8$-=Î Russian (Latin) Ì$+FJ9$-BÎ Russian (Cyrillic) Ì$+FJA$-jÎ Hungarian Ì$+FJB$-oÎ Slovenian, Croatian, Serbian (Latin) Ì$+FJC$-tÎ Romanian Ì$+FJD$-yÎ Czech Republic Ì$+FJE$-~Î WLS8600...
PowerScan™ M8300 Default Configuration ™ PowerScan M8300 Default Configuration DATA FORMAT code identifier disabled, field adjustment disabled, code length not transmitted, character replacement disabled CODE SELECTION Enabled codes • EAN 8/EAN 13 / UPC A/UPC E without ADD ON check digit transmitted, no conversions •...
Interfaces section, select other options and cus- tomize your reader through use of the programming barcodes available in the WLS8600 Reference Manual. Check the corresponding features section for your interface, and also the Data Editing and Symbologies chapters of the PRG.
Technical Features Technical Features WLS8600 WLS8600 Electrical Features 4 to 30 VDC Power Supply Max. Consumption: 0.076 mm (3 mils) @ 4V 420 mA 310 mA @30V 62 mA Sleep mode 4 mA Scan Rat 35 ± 5 scans/sec Good Read LED (green)
Compliance Compliance Laser Safety Compliance The laser scanner conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN60825-1 at the date of manufacture. The laser light is visible to the human eye and is emit- ted from the output window (1). Laser warning and classification label (2).
UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 4 - 30 V, minimum 420 mA, which supplies power directly to the reader via the power connector of the cable. WLS8600...
The warranty period shall extend from the date of shipment from Wasp for the duration published by Wasp for the product at the time of purchase (Warranty period). Wasp warrants repaired hardware devices against defects in work-...
NOTICE OF THE POSSIBILITY OF SUCH DAMAGES. Risk of Loss Customer shall bear risk of loss or damage for product in transit to Wasp. Wasp shall assume risk of loss or damage for product in Wasp’s possession. In the absence of specific written instruc- tions for the return of product to Customer, Wasp will select the carrier, but Wasp shall not there- by assume any liability in connection with the return shipment.
Page 21
Service and Support NOTES Quick Reference Guide...
DECLARATION OF CONFORMITY Wasp Barcode Technologies 1400 10th St Plano, Texas La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Wasp Barcode Technologies. per: This Declaration of Conformity is issued under the sole responsibility of Wasp Barcode Technologies for: Cette déclaration de conformité...
Page 24
Wasp Barcode Technologies 1400 10th Street Plano, Texas USA 75074 (Rev H) 820060290 November 2013...