Wasp WLR8950 Quick Start Manual
  1. Manuals
  2. Brands
  3. Wasp Manuals
  4. Barcode Reader
  5. WLR8950
  6. Quick start manual

Wasp WLR8950 Quick Start Manual

Hide thumbs Also See for WLR8950:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
WLR8950
Quick Start Guide

Advertisement

Table of Contents
loading

Related Manuals for Wasp WLR8950

Summary of Contents for Wasp WLR8950

  • Page 1 WLR8950 Quick Start Guide...

  • Page 2: Table Of Contents

    Table of Contents Installation Setup and Configuration Factory Default Auto-Sense Stand Mode Magnetic Switch Keyboard Connection Interface Selections Bi-Color Light Source Settings Upper/Lower Case Beep Settings Keyboard Language Terminator Code ID Barcode Test Symbols 11-13 Rev. 4/30/2012...

  • Page 3: Installation

    WLR8950 Scanner directly into your PC keyboard port. Plug your keyboard cable into the other end (female Din 6) of the the scanner. 3. Turn your computer on. USB Scanner Trigger Scanning Aperture USB Port 1. Plug the USB of the WLR8950 Scanner directly into your PC’s USB port.
  • Page 4 Your Wasp WLR8950 Scanners are ready for use. The default settings of the scanners have been pre-programmed for the most common barcode configurations. Use the “WLR8950 Setup & Configuration” sections only to customize the scanners settings. Please review the “Enable Barcode Symbologies”...

  • Page 5: Setup And Configuration

    In order to configure Wasp WLR8950 Scanners, you must familiarize yourself with the setup procedures on the following pages. The default settings of the Wasp WLR8950 Scanners are identified on each page and clearly marked using an asterisk (*). The default settings have been preprogrammed for the most common barcode configurations.

  • Page 6: Auto-Sense Stand Mode

    AUTO-SENSE & MAGNETIC SWITCH Auto-Sense Stand Mode and Magnetic Switch Scan the Auto-Sense Mode Enable barcode to enable the hands-free autosense feature of the WLR8950 Scanners. To turn this mode “off,” scan the Trigger Only barcode. Auto-Sense Mode Enable Trigger Only Magnetic Switch is available after activating Auto-Sense Stand Mode.

  • Page 7: Keyboard Connection

    KEYBOARD CONNECTION & INTERFACE Keyboard Connection The Keyboard Connection is used to program the Wasp WLR8950 Scanners for the type of computer to which it is attached. PC (USB or PS/2) * Notebook Interface Selections The Interface Selections barcodes allow you to switch interfaces based on your connection type.

  • Page 8: Bi-Color Light Source Settings

    BI-COLOR LIGHT SOURCE SETTINGS BI-COLOR LIGHT SOURCE SETTINGS Cycle Mode Cycle Mode The following settings are supported by bi-color models. The following settings are supported by bi-color models. Red > Green Red > Green Green > Red Green > Red Green >...

  • Page 9: Upper/Lower Case

    Caps Lock Off * Caps Lock Auto Beep Settings The ‘Beep’ configuration supports the general control options for the Wasp WLR8950 Scanners. The High, Low and Med settings refer to the tone of the beep, not the volume. Beep High Beep Off...

  • Page 10: Keyboard Language

    KEYBOARD LANGUAGE The ‘Keyboard Language’ setting controls the key codes for your keyboard’s language. U.S.* German Japan (106 Key Only) English UK Italian French Spanish Czech (QWERTY) Swiss Universal Code *Default...

  • Page 11: Terminator

    TERMINATOR/CODE ID Terminator The ‘Terminator’ option is used to specify the end-of-text message and is primarily used to denote the end of the barcode value. CR * None Space CR + LF Code ID The ‘Code ID’ option sends a specific value when a particular barcode symbology is scanned.

  • Page 12: Barcode Test Symbols

    BARCODE TEST SYMBOLS Note: Make sure that the appropriate barcode symbology is configured properly and enabled before trying to scan. Use the ‘Barcode Symbologies’ configuration beginning on page 14 of the User Manual to enable specific symbologies. Code 39* Code 93 Interleaved 2 of 5 * Codabar * Code 128*...

  • Page 13: Barcode Test Symbols

    BARCODE TEST SYMBOLS UPC-A* UPC-A w/5 digit supplement UPC-A w/2 digit supplement UPC-E* UPC-E w/5 digit supplement UPC-E w/2 digit supplement *Default...
  • Page 14 BARCODE TEST SYMBOLS EAN/JAN-13* EAN/JAN-13 w/5 digit supplement EAN/JAN-13 w/2 digit supplement EAN/JAN-8* EAN/JAN-8 w/5 digit supplement EAN/JAN-8 w/2 digit supplement *Default...
  • Page 15 Wasp Barcode Technologies 1400 10th Street Plano, TX 75074 www.waspbarcode.com...

Table of Contents