Rear Panel - Integra DTR-50.6 Basic Manual

1 2 3 4 5 6
G H I

Rear Panel

RI REMOTE CONTROL jack: An Onkyo product with RI
1
jack can be connected and synchronized with this unit.
FM ANTENNA jack (75 Ω) and AM ANTENNA
2
terminal: The supplied antennas are connected.
COMPONENT VIDEO IN/OUT jacks: Component video
3
input/output jacks
ETHERNET port: Used for LAN connection
4
RS232 port: Connected to the home control system. (¼)
5
IR IN A/B/OUT jack: Connected to the multiroom
6
remote control kit. (¼)
12V TRIGGER OUT A/B/C jacks: Allows you to connect
7
a device with 12V trigger input jack in a separate room
to enable link operation between the device and the unit.
(¼)
¼ Special devices or cable connections are necessary to use the control
¼
functions (5) to (7). Contact the specialized stores for more information.
HDMI IN/OUT jacks: Digital video signals and audio
8
signals are transmitted between the unit and the
connected devices.
HDBaseT™ IN/OUT ports: HDMI input signals are
9
output via the Ethernet cable. As they are covered with
7 8 9
J K L
a seal when shipped, remove it when you use the ports.
Do not use the ports to connect the Ethernet port of
network device.
AC INLET: The power cord is connected.
F
DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio
G
signals are input.
GND terminal: The ground wire of the turntable is
H
connected.
Composite video and analog audio jacks: Analog
I
video signals and audio signals are input.
MONITOR OUT V jack: Video signals are output to the
J
connected monitor or TV.
PRE OUT jacks: A power amplifier or subwoofer with
K
built-in amplifier is connected.
PRE/LINE OUT ZONE2/ZONE3 jacks: Audio output
L
jacks connected to the integrated amplifier for multi-zone
playback in a separate room.
SPEAKERS terminals: Speakers are connected. To
M
use the Multi-zone function, connect the speakers in the
separate room to the ZONE2 speaker terminals.
F
M
1 23 4
9
Display
Stays lit in the following conditions. "Z2" "Z3": Zone 2 or
1
Zone 3 output is on. / "HDMI": HDMI signals are input
and HDMI input selector is selected. / "ARC": Audio
signals are input from ARC compatible TV and TV/CD
input selector is selected. / "3D": Input signals are 3D. /
"USB" (¼): "USB" input is selected and USB storage
device is connected. / "NET" (¼): "NET" input is selected
and the unit is connected to the network. / "DIGITAL":
Digital signals are input and the digital input selector is
selected. / Cursor indicators: NET or USB is controlled.
¼ "USB" and "NET" will flash if the connection is not correct. ¼
Stays lit while headphones are connected.
2
Stays lit while NET or USB is controlled.
3
Stays lit according to the type of input digital signals and
4
the listening mode.
Stays lit while Music Optimizer is enabled.
5
Stays lit in the following conditions. "AUTO": Tuning
6
mode is auto. / "TUNED": Receiving AM/FM radio.
 flashes while tuning is automatically performed. /
"FM STEREO": Receiving FM stereo. / "RDS" (Other
models): Receiving RDS broadcasting.
"MUTING": Flashes when muting is on.
7
Stays lit in the following conditions. "SLEEP": Sleep
8
timer has been set. / "ASb" (Auto Standby): Auto
Standby is on. / "ch": Channel is being set. / "Hz":
Crossover frequencies are being set. / "m/ft": Speaker
distances are being set. / "dB": Speaker volume is being
set.
Displays various information of the input signals.
9
Pressing Display displays the type of input digital signals
and the listening mode.
5 6 7
8
17