Sharp ER-A440 Programming Manual page 13

[JOB#926] MRS = 0400
#926-A: Not used (Fixed at "0")
#926-B: 1. Program reset at PGM 2 mode
1. Program reset at PGM2 mode
#926-C: 1. Open store/Close store with on-line
2. Send AT command string with JOB#500 (Open store)
3. Send AT command string with JOB#501 (Close store)
1. Open 2. Send AT
store/Close command
store with string with
on-line JOB#500
(Open store)
No
No
Yes
No
Yes
Yes
#926-D: 1. Receive on-line channel in close store
1. Receive on-line channel in close store
[JOB#927] NOT USED: MRS = 0000
[JOB#928] NOT USED: MRS = 0000
[JOB#929] MRS = 0000
#929-A, B, C: Not used (Fixed at "000")
#929-D: 1. Taxable status of PLU which is set at "Non-taxable" by
PGM
1. Taxable status of PLU which is set at
"Non-taxable" by PGM
According to its associated Department
Non-taxable
[JOB#930∼941] MRS = 0000
RESET REPORT COUNTER
Job# @/FOR
JOB #
930 Z1 report counter
933 Hourly Z1 report counter
934 PLU Z1/Z2 report counter
935 Cashier Z1/Z2 report counter
937 Z2 report counter
939 31 day daily net Z2 report counter
Disable
Enable
3. Send AT
command
string with
JOB#501
(Close store)
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
"0000"
ABCD CA/AT
Initial value of Z countr
Function
[JOB#942, 943, 969] MRS = 0000000000000
GT COUNTER PRESETTING
926-B
Job#
0
4
JOB #
942
943
969
Note: GT1 is obtained by calculation
Equation: GT1=GT2-GT3
926-C
[JOB#944] MRS = 0000
0
PGM2 secret code presetting
1
2
3
944
4
5
NOTE: When the secret code "0" is programmed, the secret code
6
7
[JOB#950] MRS = STANDARD KEY LAYOUT
Free key layout (Except for department keys and direct PLU keys.)
926-D
0
4
950
[JOB#951] MRS = STANDARD KEY LAYOUT
929-D
Free key layout (department keys and direct PLU keys)
0
2
951
•
Programming of the keys to be dept keys or direct PLU keys on
the keyboard.
•
Key No. is assigned to each key which is supposed to be dept.
Key or direct PLU key by depressing the key after entering the key
No.
•
Those keys programmed by this job No. will be dept. keys if dept.
code is assigned, and will be direct PLU keys if PLU code is
assigned in the PGM2 mode.
– 12 –
@/FOR 0000000000000
GT2 (Positive GT)
GT3 (Negative GT)
TRAINING GT
0
@/FOR XXXX
4 digits
entry is be inhibited.
Key number manual
increment
Key number automatic
increment
@/FOR XXX
Key No.
Key number manual increment
Key number automatic
increment
@/FOR
XXX
Key No.
0
CA/AT
13 digits
Function
CA/AT
Initial setting
Free key
CA/AT
@/FOR
To inhibit
SBTL
increment key No.
Free key
CA/AT
@/FOR
To inhibit
SBTL
increment key No.