Table of Contents
Advertisement
Punching in and out
Punching in/out is a technique used to replace a part of an
already recorded track.
Start playback and when you reach the part that you want
to replace, switch to record (punch in), then switch back to
playback (or stop) when you finish replacing the part that you
want (punch out).
1. Decide what part of the track you plan to re-record.
Choose a point to begin where the new recording can sit
well with the existing recording.
2. Press the REC buttons of the tracks that you want to partially
re-record to put them into recording standby (REC buttons
start flashing).
3. Start playback before the part you want to replace.
4. When the part you want to replace is reached, press the
RECORD (
) button and start your performance.
0
Recording starts (punch in).
5. When you finish the replacement recording, press the PLAY
(
) button.
t
Playback resumes (punch out).
TIP
You can also press the STOP (
8
the replacement recording.
Using a footswitch to punch in/out
You can connect a TASCAM RC-3F footswitch (sold separately) to
the REMOTE jack on the front panel and use it to punch in and
out.
In step 4 above, step on the footswitch instead of pressing the
RECORD (
) button, and in step 5, step on the footswitch again
0
instead of pressing the PLAY (
t
NOTE
Step on the switch (pedal) that you have set to
in the footswitch settings. By default, the center pedal is set to
. (See "Setting the footswitch" below.)
PUNCH IN/OUT
Setting the footswitch
Set the footswitch on the
PREFERENCE
1. When the recorder is stopped, press the MENU button to
open the
screen.
MENU
) button to punch out at the end of
) button.
TASCAM RC-3F footswitch
(sold separately)
PUNCH IN/OUT
screen.
7 - Recorder Functions
2. Use the JOG/DATA dial or the CURSOR (
buttons to select (highlight green)
press the F4 (
) button.
t
The
screen opens.
PREFERENCE
3. Use the CURSOR (
/
) buttons to select (highlight blue)
5
b
.
Foot SW Right
4. Use the JOG/DATA dial to select the function that you want
to assign to the right pedal of the TASCAM RC-3F footswitch.
Options:
,
,
PLAY
REC
,
(right pedal default),
OUT
PLAY/STOP
5. In the same way, set
Foot SW Center
the center pedal and
Foot SW Left
Options:
,
,
PLAY
REC
(center pedal default),
OUT
(left pedal default)
CUE LOCATE
6. After making the settings, press the HOME button to return
to the Home screen.
ª Footswitch function list
Function
PLAY
Same as unit's PLAY (
REC
Same as unit's RECORD (
STOP
Same as unit's STOP (
Same as unit's F FWD (
FF
button
REW
Same as unit's REW (
PUNCH IN/
Punches in when pressed during playback,
OUT
punches out when pressed during recording.
Starts playback when stopped, stops in other
PLAY/STOP
states.
CUE LOCATE
Locates last point where playback started.
Bouncing tracks
Like many multitrack recorders, this unit allows you to bounce
tracks (ping-pong recording). Track bouncing allows you to
combine the signals of multiple tracks and use them to create
new mono or stereo recordings. In this way, you can virtually
record more than 32 tracks. Note, however, that the original
tracks cannot be separated again, so save them if they are
important to you.
/
/
/
)
5
b
g
t
, and then
PREFERENCE
,
,
,
STOP
FF
REW
PUNCH IN/
CUE LOCATE
for the function of
for the left pedal.
,
,
,
STOP
FF
REW
PUNCH IN/
,
PLAY/STOP
Description
) button
t
) button
0
) button
8
) (TO LAST REC)
,
) (TO ZERO) button
m
41
TASCAM DP-32SD
Advertisement
Table of Contents
