Location; General - Payne PG8J Installation Instructions Manual

FURNACE SIZE
CABINET WIDTH
045---08/024045 14--- 3/16
045---12/036045 14--- 3/16
070---08/024070 14--- 3/16
070---12/036070 14--- 3/16
070---16/048070
17--- 1/2
090---14/042090 17--- 1/2
090---16/048090
090---20/060090
110---12/036110 17--- 1/2
110---16/048110
110---22/066110
135---16/048135
135---22/066135 24--- 1/2
155---20/060155 24--- 1/2
* 5 ---in. or 6 ---in. vent connector may be required in some cases.
5. Use this procedure for installed and uninstalled (ungroun-
ded) furnaces.
6. Before removing a new control from its container, dis-
charge your body's electrostatic charge to ground to pro-
tect the control from damage. If the control is to be in-
stalled in a furnace, follow items 1 through 4 before
bringing the control or yourself in contact with the fur-
nace. Put all used and new controls into containers before
touching ungrounded objects.
7. An ESD service kit (available from commercial sources)
may also be used to prevent ESD damage.

LOCATION

GENERAL

This multipoise furnace is shipped in packaged configuration.
Some assembly and modifications are required when used in any
of the four applications shown in Fig. 4.
This furnace must:
S be installed so the electrical components are protected
from water.
S not be installed directly on any combustible material
other than wood flooring (refer to SAFETY
CONSIDERATIONS).
S be located as close to the chimney or vent and attached
to an air distribution system. Refer to Air Ducts section.
S be provided ample space for servicing and cleaning.
Always comply with minimum fire protection clear-
ances shown on the furnace clearance to combustible
label.
S The following types of furnace installations may re-
quire OUTDOOR AIR for combustion due to chemical
exposures:
S Commercial buildings
S Buildings with indoor pools
S Laundry rooms
S Hobby or craft rooms, and
S Chemical storage areas
S Permanent wave solutions
S Chlorinated waxes and cleaners
If air is exposed to the following substances, it should not be used
for combustion air, and outdoor air may be required for
combustion:
TABLE 1—DIMENSIONS (IN.)
A D
SUPPLY ---AIR
WIDTH (IN.)
12--- 9/16
12--- 9/16
12--- 9/16
12--- 9/16
15--- 7/8
15--- 7/8
21 19--- 3/8
21 19--- 3/8
15--- 7/8
21 19--- 3/8
21 19--- 3/8
21 19--- 3/8
22--- 7/8
22--- 7/8
E F
RETURN---AIR C.L. TOP AND
WIDTH (IN.) BOTTOM FLUE
COLLAR (IN.)
12--- 11/16 9--- 5/16
12--- 11/16 9--- 5/16
12--- 11/16 9--- 5/16
12--- 11/16 9--- 5/16
16 11--- 9/16
16 11--- 9/16
19--- 1/2 13--- 5/16
19--- 1/2 13--- 5/16
16 11--- 9/16
19--- 1/2 13--- 5/16
19--- 1/2 13--- 5/16
19--- 1/2 13--- 5/16
23 15--- 1/16
23 15--- 1/16
!
CARBON MONOXIDE POISONING AND UNIT
DAMAGE HAZARD
Failure to follow this warning could result in personal
injury or death, and unit component damage.
Corrosive or contaminated air may cause failure of parts
containing flue gas, which could leak into the living space.
Air for combustion must not be contaminated by halogen
compounds, which include fluoride, chloride, bromide, and
iodide. These elements can corrode heat exchangers and
shorten furnace life. Air contaminants are found in aerosol
sprays, detergents, bleaches, cleaning solvents, salts, air
fresheners, and other household products. Do not install
furnace in a corrosive or contaminated atmosphere. Make
sure all combustion and circulating air requirements are met,
in addition to all local codes and ordinances.
S Chlorine based swimming pool chemicals
S Water softening chemicals
S De- -icing salts or chemicals
S Carbon tetrachloride
Halogen type refrigerants
S
S Cleaning solvents (such as perchloroethylene)
S Printing inks, paint removers, varnishes, etc.
S Hydrochloric acid
S Cements and glues
S Antistatic fabric softeners for clothes dryers
S Masonry acid washing materials
All fuel- -burning equipment must be supplied with air for fuel
combustion. Sufficient air must be provided to avoid negative
pressure in the equipment room or space. A positive seal must be
made between the furnace cabinet and the return- -air duct to
prevent pulling air from the burner area and from draft safeguard
opening.
6
FLUE SHIP WT (LB)
COLLAR*
(IN.)
4
4
4
4
4
4
4
4
4
4
4
4
4
4
WARNING
104
107
111
115
126
127
140
146
135
146
152
149
163
170