Safety; Duct Systems; Electrical Connections; Location - Payne PG8JAA042090AAJA Installation And Operating Instructions Manual

MAX 85°F
--> Step 8--Venting
* US: NFO(: chapters 10 and 13
CANADA: NS(NGPIC Part 7 and Appendix C
ELECTROSTATIC DBSCHARGE {ESD) PRECAUTIONS
PROCEDURE
FRONT
MIN 60°F
Fig, 3--Return Air Temperature
A02055
In the [ nited States and Canada, follow all codes and standards for
the ibllowing:
Step l--Safety
* US: National Fuel Gas Code (NFGC) NFPA 54 2002/ANSI
Z223.1 2002 and the Installation Standards, Wam_ Air Heating
and Air Conditioning Systems ANSI NFPA 90B
--> * CANADA: CSA B149.1-00 National Standard of Canada
Natural Gas and Propane Installation Codes (NSCNGPIC)
Step 2--General hstaHation
* US: Current edition of the NFGC and the NFPA 90B. For
copies, contact the National Fire Protection Association Inc.,
BattelTmarch Park, Quincy, MA 02269 (www.NFPA.org); or
for only the NFGC, contact the American Gas Association, 400
N. Capitol Street, N.W., Washington, DC 20001
(www.AGA.org).
* CANADA: NSCNGPI(. For a copy, contact Standard Sales,
CSA International, 178 Rexdale Boulevard, Etobicoke (Tor-
onto), Ontario, M9W 1R3 Canada
Step a--Combustion and Ventilation Air
--> * US: Section 8.3 of the NFGC, Air for (ombustion and
Ventilation
* CANADA: Part 7 of NSCNGPIC, Venting Systems and Air
Supply fbr Appliances
Step 4--Duct Systems
--> * US and CANADA: Air (onditioning Contractors Association
(ACCA) Manual D, Sheet Metal and Air Conditioning Con=
tractors National Association (SMACNA), or American Soci=
ety of Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE) 2001 Fundamentals Handbook Chapter 34 or 2000
HVAC Systems and Equipment Handbook Chapters 9 and 16.
Step 5--Acoustical Lining and Fibrous Gtass Duct
* US and CANADA: current edition of SMA(NA and NFPA
90B as tested by [L Standard 181 _br Class I Rigid Air Ducts
Step 6--Gas Piping and Gas P{pe Pressure Testing
* US: NFGC; chapters 5, 6, 7, and 12 and National Phnnbing
Codes
* CANADA: NSCNGPIC Parts 3, 4, and 5, and Appendices A,
B, E and H
Step 7--Electrical Connections
* US: National Electrical Code (NEC) ANSI NFPA 70 2002
* CANADA: Canadian Electrical Code CSA C22 1
--€ FURNACE RELIABILITY HAZARD
Improper installation or service of furnace may cause prema-
ture furnace component failure
Electrostatic discharge can affect electronic components.
Take precautions during thrnace installation and servicing to
protect tl_e furnace electronic control. Precautions will pre-
vent electrostatic discharges ti'om personnel and hand tools
which are held during the procedure. These precautions will
help to avoid exposing the control to electrostatic discharge
by putting the thrnace, the control, and the person at the same
electrostatic potential.
1 Disconnect all power to the furnace. Multiple disconnects may
be required. DO NOT TOUCH THE CONTROL OR ANY
WIRE CONNECTED TO THE CONTROL PRIOR TO DIS-
CHARGING YOUR BODY'S ELECTROSTATIC CHARGE
TO GROUND.
2 Firmly touch the clean, unpainted, metal surface of the f_maace
chassis which is close to the control. Tools held in a person's
hand dtlring grounding will be satisfactorily discharged.
3. After touching the chassis, you may proceed to service the
control or connecting wires as tong as you do nothing to
recharge your body with static electricity (for example; DO
NOT move or shuffle your feet, do not touch ungrounded
objects, etc.).
4. If you touch ungrounded ohjects (and recharge your body with
static electricity), firmly touch a clean, unpainted metal
surface of the fiul_ace again be:_bre touching control or wires.
5. Use this procedure for installed and uninstalled (ungrounded)
_i/rnaces
6. Before removing a new contact fi'om its container, discharge
your bo@'s electrostatic charge to ground to protect the
control _i'om damage. If t!_e control is to be installed in a
_i/mace, _bltow items 1 through 4 befbre bringing the control
or yourself in contact with the furnace. Put all used and new
controls into containers be_bre touching ungrounded objects.
7. An ESD service kit (available from commercial sources) may
also be used to prevent ESD dan?age.
LOCATION
GENERAL
Some assembly and modifications are required when used inany
of the four applications shown in Fig. 4,
This lhrnace must:
* be installed so the electrical components are protected from
water
not be installed directly on any combustible material other than
wood flooring (refer to SAFETY CONSIDERATIONS)
* he located close to d-_echinmey or vent and attached to an air
distribution system, Refer to Air Ducts section,
* be provided ample space fbr servicing and cleaning. Always
comply with mininmm fire protection clearances shown on the
fro'hate clearance to combustible consm/ction 1abel