Bellows. Replacement - Polaroid 100 Series Repair Manual

r;.u:ing: away from the bellows ,tnd
halld-pre~s
il ill
pl:ll:'..'.
5. In1'I"lIlllI.' haseplate into the shutler housing
:lilt!
then install the shutter housing as
roJ ­
lows;
a. 01'1 shunen with C'opper-colored mylar
printed circuits: Route the battery c.lble
through the
opening
in
the rear shutter and
reinstall the rubber strain reUef coliar using
Pliohond
(or
equivalent). Using an Unpr
Princess so)dering iron (or .:quivalentJ. cart?
fully solder the battery wires to their
wn~
tai:lS on the printed circuit. On shutters
wilh dear teflon printed citcuits folder
Model 100 cameras): Position the shutter
in
the rear shutter housing, routing the battery
C"Jble through the opening in the housing
and then through the bellows tabs. Replace
the metal banding clip and solder the black
lead to the shutter interlock, Strip the
insu~
lation from the cut ends of the white wire
and slide
a
piece
of
heat--shrink tubing down
OJl~
length of the white wire. Solder the two
ends or the white wire together and slide the
heat-shrlnk tubing over the splice, Apply
beal to tighten the tubing, On other
shut~
lets: Draw the battery cable through the
opening in the shutter housing and reinstall
Ihe rubber strJin-relief collar using Piiobond.
Solder the banery' cable leads to their
con~
l:.Io.;ls on
the electronic module.
b. Se.:ure the bnsc block and electronic module
to
Ill..; froill shutter hOllsing with the mount~
ing s..;rews. IOn ~me cameras the shutter is
positioned over plastic posts on the front
!iillllfCr
housing.)
c. fock rhe shutter and move the slide block
on the rt.'ar shutter housing aU the way
down. Vt.'ry carefully position the shutter
11110
the
f\.'ar housing. Be
sure
the shutter
tmsket is in pia!:\: 01\ the rcar housin{!. SL'­
I..'ure the front housing to the n:ar hOllsing
with the shuner housing screws, Usc
screw~
driver 111040.
Do not lighten th.., housing
screw loe;ned at the top of the cabk release
cOVt,'T, (On Cltmeras where applicabJe, instan
the
lOP
etch plalt:.)
6. PosUion the cable release in its cover O'n the
rear sJ1Utter housing and tighten the three
screws.
7. Check the action of the shutter release
but~
ton according to procedures in Section 111.
8.
PerfO'rm
the
lens and rangefinder/viewfinder
checks described in Section Ill.
BELl.OWS REPI.ACEMENT
Removal
I. Carefully peel the battery cable tabs free of
the bellows.
2. Loosen the cable release cover, freeing the
cable from the rear shutter housing,
3. Remove the beUows from the rear shutter
housing as follows: (Retain the light seal
if
Jt is in good condition).
Models 100.240.250.350& 360:
Remove the four beUows screws.
All OIlier Models:
Carefully remove the four bellows fasteners using
tool #CR1OO6 (Figure 5-8). If any of the plastic
pOSlS
on the housing break. repair them as fonows:
a. File the broken post untH it is flush with the
bellows plate.
b. Set the drill to the corre<:t height by
insert~
illg the drill in jig #CR I025 and adjusting
the ~t screw in the collar until the drill pro ­
SPECIA4- JIG
L
-4
F ,G. 5.10 P RE"' P C;A"R' " ' , "' N "' G -oT"' H ""E;:-;;O' " ' R ' " ";-L;-L_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
..J
44
COLLAR