Advertisement
3. Select the SSID of your device, and then click Connect. The following
Access the WebGUI Configuration Page
figure is only for your reference.
1. Make sure the connection between your device and the client is correct.
2. Launch the internet browser and enter http://192.168.0.1 or http://ufi.
home in the address bar.
Notes:
It is recommended that you use IE (7.0 or later), Firefox (2.0 or later), Opera
(10.0 or later), Safari (4.0 or later), Chrome (5.0 or later).
3. The login page appears as follows. The following figure is only for your
reference.
Notes:
There will be a pop-up window to require the password. Check the label
on your device to gain the SSID and preset password information. Please
do remember the new password when you change the password by
selecting Settings > Wi-Fi Settings > Security after logging in the WebGUI
Configuration Page. You can restore the device to the factory default settings
in case you forget it.
4. Wait a moment, the connection between your device and the client will
be established successfully.
Access the Internet
View the information of WAN, WLAN and Device. Input the case-sensitive
1. Switch on the device.
default password "admin", and then click Login to access the WebGUI
2. Establish a connection between your device and the client.
Configuration page.
3. After successfully establishing the connection, access the Internet in the
Notes:
Always On and Manual mode. The default mode is Always On.
•
Do not put anything on the top of your device. Do not lay devices to
Notes:
overlap each other when using.
You can browse the WebGUI Configuration page and click WAN Connection
•
The device takes 1~2 minutes to initialize, and attach to the network.
to set the WAN connection mode.
10
11
PIN Code Verification
Notes:
The parameter settings may have been preset by your service provider,
If the PIN code of your SIM card is enabled, you will need to input the PIN
and you will enjoy your Internet service directly. Please contact your service
code when you login at the first time.
provider for details if you want to do some modification.
WAN Connection
After logging in, select WAN Connection, and you can choose the WAN
Connection Mode according to your requirement.
Notes:
The SIM card will be locked if you enter wrong PIN code consecutively for
three times.
If you want to modify the PIN Status, please select Settings > Advanced >
PIN Manage to do the actions.
Settings
After logging in, select Settings, and you can do the following operations.
Select Settings >
View the Wireless Information, select Band Selection
3G Settings
Mode and change APN Setting.
View the current station list, change the basic wireless
Select Settings >
network settings, choose security mode and WPA type,
Wi-Fi Settings
Quick Settings
and perform the WPS configuration.
After logging in, select Quick Setup, and then the Quick Setup wizard
Select Settings >
Set the Mac/IP/Port Filtering, Port Forwarding or the
appears.
Firewall
System Security configuration.
View the current status of your device, change the
Select Settings >
Administrator Settings, restore factory defaults, manage
Advanced
PIN or set the LAN interface configuration.
Notes:
Make sure that you can remember the new password if you change the
The Quick Settings wizard guides you how to set the basic parameters for
login password by selecting Settings > Advanced > Management. Please
your device in the safest way. After this procedure, you can use your Internet
restore the device to the factory default settings in case you forget the new
service.
password.
12
13
Disconnect from the Internet
Usage of WPS
1. Log in the WebGUI Configuration page, and select WAN Connection.
If your client device supports WPS, you need not to input the password
2. Select Manual > Disconnect Internet.
manually after WPS has been available. Please do the following:
3. Click Apply.
1. Start up your device.
2. Launch the client device connected to your device.
3. Enable the WPS function of your device.
4. Enable the WPS function of the client.
Notes:
•
If the current security mode of the device is OPEN or SHARE, the WPS
function is useless.
Notes:
•
For the detailed operations about the client, please refer to the client's
Turning off the device can also terminate the internet connection.
instruction.
SMS
Sleep Mode
This function allows you to view, send and receive short messages.
When you enable the Wi-Fi function and use the battery to supply power
After logging in, select SMS, and you can do the following operations.
to the device, once no user connects to the device within 10 minutes or
Select SMS > Device
Operate the SMS in your device.
you press the WPS button, the device will enter the sleep mode, and the
LED screen will be turned off. In the sleep mode, the Wi-Fi function will be
Select SMS > SIM Card
Operate the SMS in your SIM card.
disabled. Press Power or WPS button to wake up the device, and the LED
Select SMS > New Message
Send or save SMS.
screen will be turned on.
Select SMS > SMS Settings
Set the SMS configuration.
Notes:
With USB connection if no Wi-Fi user connects to the device within 10
PhoneBook
minutes, only the Wi-Fi function will be disabled. Hold the WPS button about
3 seconds to enable this function.
This function allows you to store contacts to your device or SIM card.
Warning and Notice
After logging in, select PhoneBook, and you can add a new contact in Add
New tab, and perform operations to the contact in the Device or SIM Card
tab.
To the Owner
•
Some electronic devices are susceptible to electromagnetic interference
sent by your device if inadequately shielded, such as the electronic
system of vehicles. Please consult the manufacturer of your device
before using if necessary.
14
15
•
Operating your device may interfere with medical devices like hearing
•
Operating temperature range of 0ºC ~ +35ºC and humidity range of
aids and pacemakers. Please always keep them more than 20
5% ~ 95% are recommended.
centimeters away from such medical devices when they are turned
Using Battery
on. Turn your device off if necessary. Consult a physician or the
manufacturer of the medical device before using your device.
•
Do not short-circuit the battery, as this can cause excessive heat and
•
Be aware of the usage limitation when using your device at places such
fire.
•
Do not store battery in hot areas or dispose of it in a fire to avoid
as oil warehouses or chemical factories, where there are explosive gases
explosion.
or explosive products being processed. Turn off your device if required.
•
The use of electronic transmitting devices is forbidden in aircrafts, at
•
Do not disassemble or modify the battery.
petrol stations and in hospitals. Please observe and obey all warning
•
When not using the battery for a long period, remove it from your device
signs and switch off your device in these conditions.
and store it in a cool dry place.
•
Never use any charger or battery damaged or worn out.
•
Do not touch the inner antenna area if not necessary. Otherwise it will
affect your device's performance.
•
Return the wear-out battery to the provider or put it in the appointed
•
Store your device out of the reach of little children. Your device may
recycle place. Do not put it in familial rubbish.
cause injury if used as a toy.
Warning:
If the battery is broken, keep away from it. If it taints your skin, wash your
•
Do not touch the metallic parts of your device so as to avoid a burn,
skin with abundant fresh water and ask doctor help if necessary.
when your device is working.
Using Your Device
Limited Warranty
•
Please use original accessories or accessories that are authorized. Using
•
This warranty does not apply to defects or errors in the Product caused
any unauthorized accessories may affect your device's performance, and
by:
i.
Reasonable abrasion.
violate related national regulations about telecom terminals.
•
Avoid using your device near or inside metallic structures or
ii. End User 's failure to follow ZTE's installation, operation or
establishments that can emit electromagnetic waves. Otherwise it may
maintenance instructions or procedures.
influence signal reception.
iii. End User's mishandling, misuse, negligence, or improper installation,
disassembly, storage, servicing or operation of the Product.
•
Your device is not waterproof. Please keep it dry and store in a shady
iv. Modifications or repairs not made by ZTE or a ZTE-certified
and cool place.
•
Do not use your device immediately after a sudden temperature change.
individual.
In such case, it will produce dew inside and outside your device, so don't
v. Power failures, surges, fire, flood, accidents, actions of third parties
use it until it becomes dry.
or other events outside ZTE's reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-party
•
Handle your device carefully. Do not drop, bend or strike it. Otherwise
your device will be damaged.
products provided that such defects are due to the combined usage.
•
No dismantling by non-professionals and only qualified technicians can
vii. Any other cause beyond the range of normal usage intended for the
undertake repair work.
Product.
16
17
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
•
This warranty is End User's sole remedy and ZTE's sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose, unless
otherwise required under the mandatory provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with
using of this product, whether or not ZTE had been advised, knew or should
have known of the possibility of such damages, including, but not limited to
lost profits, interruption of business, cost of capital, cost of substitute facilities
or product, or any downtime cost.
How to Get Help
You can get help by:
•
Sending E-mail to mobile@zte.com.cn
•
Visiting http://www.zte.com.cn
•
Calling Service Hotline: +86–755–26779999
18
Advertisement
