Zte MF62 User Manual

Introduction
ZTE MF62 is a 3G/2G mobile hotspot device, working in GSM/GPRS/
EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to
it via USB or Wi-Fi interface. The device supports data and SMS services,
enabling you to communicate anytime and anywhere.
This manual provides instructions on how to install and get started with the
product. For information about connection of services, please consult your
ZTE MF62
service provider.
User Manual Specification
HSPA+: DL 21.6Mbps,
UL 5.76Mbps
Data Service
WCDMA CS: 64kbps UL/DL
WCDMA PS: 384kbps UL/DL
Interface USB and Wi-Fi
Wi-Fi Standard 802.11b/g
LEGAL INFORMATION
Wi-Fi Security WEP/WPA/WPA2
Copyright © 2011 ZTE CORPORATION.
USB Version USB 2.0 HIGH SPEED
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
USB Interface Type Micro USB
utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without the prior written permission of ZTE Weight 86g
Corporation.
Dimensions (W×H×D): 99.6mm*54mm*14.6mm
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
microSD card Support up to 32GB microSD card
Version No. : R1.0
Power Adapter 5V/700mA
ZTE CORPORATION
Battery 1500mAh
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057 Tel: +86-755-26779999 *Standby time 100hours
URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn
1 2
Interface and Buttons
*Working time 4hours
Windows 7, Windows Vista(32bit or 64bit), 1. Power Hold the Power button to switch on/off the device.
Operate system
Windows XP (SP2 or later), MAC (10.4 or later)
2. Memory card slot It is where you insert the memory card (microSD
(microSD card) card).
IE (7.0 or later), Firefox (2.0 or later), Opera (10.0
Web Browser
or later), Safari (4.0 or later), Chrome (5.0 or later)
This button is used to start/end Wi-Fi Protected
Setup authentication process and enable/disable
Operating temperature 0ºC ~ +35ºC
the Wi-Fi function.
Storage temperature -20ºC ~ +50ºC
• Hold it for 3 seconds to activate the WPS
3. WPS
function.
Charging temperature 0ºC ~ +45ºC
• When the WPS function is available, press it to
Humidity 5%~ 95%
deactivate the WPS function.
• Press it to enable/disable Wi-Fi function.
Notes:
microSD is a trademark of SD Card Association. It indicates the signal type, signal strength, battery,
4. LED Screen
Wi-Fi, etc.
The device's standby and working time are only for your reference, and
based on ideal working environment. 5. External Antenna It is used to connect an external antenna to
Connector enhance the signal strength.
Getting to Know Your Device
• Charge your device.
6. Charger/USB port
The following figure shows the appearance of the device, it is only for your
• Connect the client to your device via USB cable.
reference. The actual device may be different.
Notes:
• Hold the WPS and Power buttons simultaneously until the LED
screen turns off, and then release the buttons. The device will restart
automatically and restore to the factory default settings.
• Please use the original external antenna if necessary.
LED Indicator
When the device is powered on, the following icons will appear on the LED
screen, with the corresponding indicates listed in the table below:
Right Side Front Left Side Bottom
3 4
2. Insert the SIM card into the SIM card holder.
Icon Indication
Network signal strength.
Network type. 2G or 3G icon will appear on the LED
screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication. 3. Insert the battery as shown with the contacts located against the metal
springs, and press the battery down into the case.
New message received.
Wi-Fi Status and number of the connecting users.
Battery power indication.
Hardware Installation
Inserting SIM Card and Battery
4. Slide the back cover and lock the cover in its place.
1. Slide the back cover and remove it.
5 6
Inserting microSD Card
Working Mode
1. Pull the microSD cover out of the card slot.
Notes: Your device supports three working modes. For the client, we only use PC or
laptop as the example in this document.
Do not pull the cover rudely, as it is connected with the device.
USB Mode: Connect to the device with the USB cable.
2. Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
Wi-Fi Mode: Connect to the device via Wi-Fi.
3. Close the microSD cover.
Switching On/Off Your Device
Hold the Power button to switch on/off the device.
Notes:
The device is powered on when the LED screen lights up.
Charging Your Device
You can charge your device by using USB cable or adapter.
1. Insert the charger lead carefully.
2. The plug only fits one way. Do not use excessive force to insert the plug.
Mixed Mode: Connect to the device with the above two connection methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure that
the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices can
surf on the Internet at the same time.
7 8
Establish a connection between your device and
the client
Via USB Cable
1. Connect your device and the client with the USB cable.
2. Power on your device.
3. Follow the system prompts to complete the software installation.
Notes:
• If the system does not launch installation automatically, you can run the
installation program in path of My Computer > Mobile Hotspot.
• The driver of your device will be installed at the same time.
4. After the installation, the system will create a shortcut icon on your
desktop and a Mobile Hotspot program group in the Start→Programs
menu. The connection between your device and the client will be
established successfully a moment later.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search the available
wireless network.
Notes:
You need to check your Wireless Network Connection. Set the client
to obtain an IP address automatically in the Internet protocol (TCP/IP)
properties, and the client will get an IP address like "192.168.0.100".
9