Power Saving Mode - Toshiba RAV-SM564CT-E Installation Manual

Ceiling Type
To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the
room, the detection temperature of heating can be
raised. Also use a circulator or other device to circulate
heat air near the ceiling.
Follow to the basic operation procedure
1 2 3 4 5 6
→ → → → →
( ).
3
• For the CODE No. in Procedure , specify [06].
4
• For the set data in Procedure , select the SET
DATA of shift value of detection temperature to be
set up from the following table.
SET DATA Detection temperature shift value
0000 No shift
0001 +1 °C
+2 °C
0002
(Factory default)
0003 +3 °C
0004 +4 °C
0005 +5 °C
0006 +6 °C

Power saving mode

Performing settings of the power saving
mode
* When an outdoor unit RAV-SP***2AT / SM***3AT
type or earlier is used, the power level is fixed to 75
% regardless of the value on the display.
1
Push button for 4 seconds or more
when the air conditioner is not working.
flashes.
Indicates CODE No. "C2."
2
Select an indoor unit to be set by pushing
(left side of the button).
Each time the button is pushed, unit numbers
change as follows:
UNIT No. UNIT No. UNIT No.
1-1 1-2 1-3
UNIT No.
1-4
The fan of the selected unit runs.
27-EN
Installation Manual
3
Adjust the power save setting by pushing
TIME buttons.
Each push of the button changes the power level
by 1 % within the range from 100 % to 50 %.
*The factory default is 75 %.
Setting of power level in
power saving mode
4
Determine the setting by pushing button.
5
Push button to complete the setting.
Remote controller switch
monitoring function
This function is available to call the service monitor
mode from the remote controller during a test run to
acquire temperatures of sensors of the remote
controller, indoor unit, and outdoor unit.
2
4
1 3
1
Push and buttons simultaneously for
at least 4 seconds to call the service monitor
mode.
The service monitor indicator lights up and the
header indoor unit number is displayed first.
CODE No. is also displayed.
2
Pushing TEMP. buttons, select the
number of sensor (CODE No.) to be
monitored.
(See the following table.)
Ceiling Type
3
Pushing (left side of the button),
select an indoor unit to be monitored. The
sensor temperatures of indoor units and
their outdoor unit in the control group are
displayed.
4
Push button to return to the normal
display.
Indoor unit data
CODE No. Data name
01 Room temperature (remote controller)
02 Indoor unit intake air temperature (TA)
Indoor unit heat exchanger (coil)
03
temperature (TCJ)
Indoor unit heat exchanger (coil)
04
temperature (TC)
Indoor unit fan cumulative operating hours
F3
(x1 h)
Outdoor unit data
CODE No. Data name
Outdoor unit heat exchanger (coil)
60
temperature (TE)
61 Outside air temperature (TO)
62 Compressor discharge temperature (TD)
63 Compressor intake temperature (TS)
64 —
65 Heatsink temperature (THS)
6A Operating current (x1/10)
Compressor cumulative operating hours
F1
(x100 h)
– 14 –
Installation Manual
Group control
Simultaneous twin, triple or double twin
system
A combination with an outdoor unit allows
simultaneous ON / OFF operation of the indoor units.
The following system patterns are available.
- Two indoor units for the twin system
- Three indoor units for the triple system
- Four indoor units for the double-twin system
▼ Twin system
Outdoor unit
Indoor unit Indoor unit
Remote
controller
Finish of address setup by power-ON
▼ Triple system
Outdoor unit
Indoor unit Indoor unit Indoor unit
Remote
controller
Finish of address setup by power-ON
▼ Double twin
Outdoor unit
Indoor unit Indoor unit Indoor unit Indoor unit
Remote
controller
Finish of address setup by power-ON
• For wiring procedure and wiring method, follow to the
"Electrical connection" in this manual.
• When the power supply has been turned on, the
automatic address setup starts and which indicates
that address is being set up flashes on the display
part.
During setup of automatic address, the remote
controller operation is not accepted.
Required time up to the finish of automatic
addressing is approx. 5 minutes.
EN
28-EN