Toshiba RAV-SM564CT-E Installation Manual page 17

Ceiling Type
5
1) Specify CODE No. [14] TEMP.
buttons.
(CODE No. [14]: Group address)
2) Change the SET DATA from [0001] to [0002]
TIME / buttons.
(SET DATA [Header unit: 0001] [Follower unit:
0002])
3) Push button.
In this time, the setup finishes when the display
changes from flashing to lighting.
Indoor UNIT No. before setup change is displayed.
6
If there is other indoor unit to be changed,
2 5
repeat procedure to to change the setup.
When the above setup has finished, push
to select the indoor UNIT No. before change of
setup, specify CODE No. [12], [13], [14] in order
with TEMP. / buttons, and then check the
changed contents.
Address change check Before change:
[3-3-1] → After change: [2-2-2]
Pushing button clears the contents of which
setup was changed.
2
(In this case, procedure from is repeated.)
Indoor UNIT No. before setup change is displayed.
31-EN
Installation Manual
7
After check of the changed contents, push
button.
/
(Setup is determined.)
When button is pushed, the display disappears
and the status becomes the usual stop status.
(When button is pushed the operation from the
remote controller is not accepted for approx.
1 minute.)
*If the operation from the remote controller is not
accepted even 1 minute or more passed after
pushing button, it is considered that the
address setup is incorrect.
In this case, the automatic address must be again
set up.
Therefore repeat procedure of the setup change
1
from the Procedure .
To recognize the position of the
corresponding indoor unit though the
indoor UNIT No. is known
Check the position during operation stop.
(Stop operation of the set.)
1,3
Ceiling Type
1
Push +
4 seconds or more.
After a while, the display part flashes and the
display appears as shown below.
In this time, the position can be checked because
fan of the indoor unit operate.
• For the group control, the indoor UNIT No. is
displayed as [
units in the group control operate.
Check the displayed CODE No. is [01].
• When the CODE No. is other than [01], push
button to erase the display and repeat
procedure from the first step.
(After pushing
controller is not accepted for approx. 1 minute.)
(* Display changes according to
the model No. of indoor unit.)
2
In the group control, every time
button is pushed, the indoor UNIT No. in the
group control is displayed in order.
In this time, the position of the indoor unit can be
confirmed because only fan of the selected indoor
unit operate.
(For a group control, No. of the firstly displayed
indoor unit becomes the header unit.)
3
After confirmation, push
the mode to the usual mode.
When button is pushed, the display disappears
and the status becomes the usual stop status.
1 (When button is pushed the operation from the
remote controller is not accepted for approx. 1
minute.)
2
– 16 –
8 °C operation (SDI series 4
buttons simultaneously for
and DI series 4 only)
Pre-heating operation can be set for cold regions
where room temperature drops to below zero.
1
Push +
for 4 seconds or more when the air
] and fans of all the indoor
conditioner is not working.
After a while, the display part flashes as shown
below. Check the Displayed CODE No. is [10].
• When the CODE No. is other than [10], push
button to erase the display and repeat
procedure from the first step.
button, operation of the remote
(After pushing
remote controller is not accepted for approx. 1
minute.)
(* Display changes according to
the model No. of indoor unit.)
2
Every time
indoor unit No. in the group control is
displayed in order.
Select the indoor unit of which setup is changed.
In this time, the position of the indoor unit of which
setup is changed can be confirmed because fan of
the selected indoor unit operate.
button to return
3
Specify CODE No. [d1] TEMP.
buttons.
4
Select SET DATA [0001] TIME
buttons.
SET DATA
0000
0001
5
Push button.
In this time, the setup finishes when the display
changes from flashing to lighting.
6
Push
When
disappears and the status becomes the usual stop
status. (When
from the remote controller is not accepted for
approx. 1 minute.)
Installation Manual
+ buttons simultaneously
button, operation of the
button is pushed, the
/
/
8 °C Operation setting
None
(Factory default)
8 °C Operation setting
button.(Setup is determined.)
button is pushed, the display
button is pushed the operation
EN
32-EN