Related Manuals for GRAUPNER Polaron EX
Summary of Contents for GRAUPNER Polaron EX
- Page 1 2 CH DC CHARGER OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
-
Page 2: Table Of Contents
SPECIFICTION 7~8P CHARGER CONTROL IDENTIFICATION 9~10P Thank you for purchasing POLARON EX 2CH DC Charger. This system is extremely MENU CONFIGURATION versatile and may be used by beginners and pros alike. In order for you to make the ACTION BUTTONS best use of your system, please read this manual carefully. -
Page 3: Box Contents 5P
- Do not use in the too cold place or hot place, charge may not output normally or may not ◎ BOX CONTENTS be operated. - Make sure to use in a well ventilated place and do not block the cooling fan (rear) and air 1. - Page 4 1.80 ~ 2.45V/cell ◎ SPECIFICATION NiCd, NiMH 0.10 ~ 1.30V/cell LiPo 2.50 ~ 4.20V/cell MODE TYPE SPECIFICATION Discharge Voltage LiIon 2.50 ~ 4.10V/cell Power Supply DC Input 11-28V DC/AC by SMPS LiFe 2.00 ~ 3.70V/cell Memory 40 (CH1 20/ CH2 20) 1.50 ~ 2.00V/cell Display 3.0”...
-
Page 5: Charger Control Identification 9~10P
◎ CHARGER CONTROL IDENTIFICATION BACK FRONT RIGHT ④ ⑤ ⑥ ② ⑦ ⑧ ⑪ ① ⑨ ③ ⑩ ⑫ ⑬ ⑭ ⑤ LED Indicator for Charge/ discharge ① Mini USB ② DC Input ③ Fan ④ 3.0”TFT LCD W/Touch Screen ⑥... -
Page 6: Menu Configuration 11P
USER SET POLARON EX 2CH DC charger has two sets of outputs on the front of the charger. Channel 1 is on the left and channel 2 on the right. Each channel has two 4mm banana sockets and 7 cell balance port and - Tapping icons on main page allows to access to the tapped a temperature sensor input port. -
Page 7: Display
Display ◎ CHARGE PAGE PROFILE 00:00:00 Number of cells in series When to tap CHARGE icon on main page, you may access to charge mode. The parameters in BATTERY NAME this mode depends on the selected battery type at profile page TYPE LiPo Memory number &... -
Page 8: Nicd/ Nimh Battery Charge Setup 15P
- Cut-Temp : Cut off temperature. When used with the optional temperature sensor, a safety cut-off The programmed data is stored to memory and ready to charge battery now. Tapping Enter button makes temperature can be set, so that charging or discharging is terminated automatically if the the charger initiated to charge battery after the process of balance connector checking, charge mode temperature sensor detects the battery temperature rising above the preset temperature. - Page 9 < NORMAL > Charge mode of POLARON EX CHARGER NiCd/NiMH : The charger will charge the pack with the preset charge current, but will stop charging every minute to calculate voltage and detect Delta peak. This allows for better peak detection so it...
-
Page 10: Discharge Page
This page shows the charging process with parameters and graph. ◎ DISCHARGE PAGE Voltage and current will reach to the preset parameters. The preset current might have limitation depending on charge/discharge capacity When to tap DISCHARGE icon on main page, you may access to discharge mode. The program- and input voltage setup. -
Page 11: Lipo, Lilon, Life, Nicd, Nimh, Batteries Discharge Process 21P
3 minutes since the charge started without any control of it. Below picture shows the sequence of charging Discharge mode of POLARON EX CHARGER LiPo, Lilon, LiFe, NiCd, NiMH batteries discharge process LiPo, LiIon, LiFe... -
Page 12: Cycle Page
This page shows the discharging process with parameters USER NAME and graph. Voltage and current will reach to the preset pa- rameters. The preset current might have limitation depending on charge/discharge capacity and input voltage setup. Max Tap CYCLE icon at main page to charge is 400W and max discharging is 60W access to cycle mode When to tap graph, the data view page is accessed. -
Page 13: Cycle Operation Mode Per Battery Type 25P
Cycle operation mode per battery type The preset current might have limitation depending on charge/discharge capacity and input voltage setup. Max charge is Cycle charge discharge mode of POLARON EX 400W and max discharging is 60W LiPo, LiIon, LiFe, Pb... -
Page 14: Balance Page
Center voltage Range voltage When to STOP button, the pop up window appears which asks whether to stop operating. When to tap STOP or ESC button, the charger will stop or continue the cycle Cell Voltage Manual / Auto ▲ BALANCE MODE 1 ▲... -
Page 15: User Setup Page
Finish Sound : 10 kinds of sound is available Cycle number Sound Time : The time that the charger sounds Discharge time Charge time ON, OFF, 5sec, 15sec, 1min are available Average voltage Peak voltage Beep : It can be turned on/off to select internal or external button Discharge capacity Charge capacity... - Page 16 1) Servo test division (Screen top) ◎ MISE PAGE (Addition function) - Connect Servo to the connecter in the right side of charger, refer below picture When to tap MISE icon on main page, you may access to MISE mode and program Servo, Brushless/Brushed power motor, Warmer function.
- Page 17 The optional accessory Brushed motor setup Connect motor to 4mm banana charge socket and tap MOTORicon to access motor setup mode This page is consisted of 3 menus Wire splitter for testing motor sensor (S8002) Connection configuration for ESC, Motor, Battery, Wire splitter 1) Break-In - Motor is operated and tamed with the preset voltage for the preset time The operating time is set by minute, second...
- Page 18 Setting the number of cycle, 1~10 cycles Setting the operating voltage, operating time, delay time for each 4 steps The operating cycle number 1) Battery Warmer - Lithium type batteries in low temperature tend not to output normally. This function is used 3) Motor test to warm battery to lead to output normally when to store batteries outdoor.
- Page 19 1. Data Initialization Temperature setup Alarm setup Alarm rings on the preset time and the charger still keeps operating. When to tap STOP button, alarm is stopped *** Factory Data *** When to tap No1, you may access to factory data mode. Output voltage setup Initializing Data...
- Page 20 RESOURCE UPGRADE <Image & Sound> Press the button. POLARON EX DC charger has a number of error and warning ‘Download Start ’ messages that are designed to advise the user of any problems. When applicable, tapping error message clears the message <...
- Page 21 Low Output-Volt BLC Volt Low Output voltage is lower Balancer cell voltage is ◆ The out voltage setup is lower than than the selected cells too low ! charging/discharging battery or the number of cells ◆ Balancer cell voltage is too low or voltages.
- Page 22 ◎ NEW BATTERY CHARGE ◎ USE OF PROBLEM AND PRECAUTION FOR POLARON EX DC CHARGER - Turning on the charge, but LCD Screen is off - When the new NiCd/ NiMH are charged at the first time, charge process might be .
- Page 23 - Lithium Ion/Polymer battery packs must NEVER be discharged below 3 volts per cell (Li-Fe 2.0V) as Product(s): POLARON EX DC Battery Charger this will result in damage to the cells. If the voltage is allowed to drop below 3 volts per cell the...