Identification Of Controls; Front Panel - NAD T 787 Owner's Manual

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 2 3
1 2 3
AV Surround Sound Receiver T 787
d
a s
f
10
10
1 STANDBY BUTTON
• Press this button to switch ON the T 787 from standby mode. The
Standby LED indicator will turn from amber to blue and illuminate
the VFD. Pressing the STANDBY button again turns the unit back to
standby mode.
• The T 787 can also be switched ON from standby mode by pressing
any of the front panel buttons.
NOTE
The rear panel POWER switch must be in the ON position for the Standby
button to activate.
2 STANDBY LED
• This indicator will light up amber when the T 787 is at standby
mode.
• When the T 787 is powered up from standby mode, this indicator
will illuminate blue.
• If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY button
is pressed to switch the T 787 to standby mode, the VFD will be
extinguished but the STANDBY LED remains illuminated blue.
This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. The
corresponding active Zone icon(s) will also remain displayed in the
VFD.
• In order to completely shut down the T 787 with Zone 2, Zone 3
and/or Zone 4 still ON, press and hold STANDBY button until the
STANDBY LED turns amber.
3 NAVIGATION and ENTER BUTTONS
The navigation ([d/f/a/s]) and [ENTER] buttons have various
applications specific to given modes. The middle round button is
designated as [ENTER] button; this is normally pressed to complete a
selection, procedure, sequence or other applicable functions.
6
4 5
4 5
NAD T787
MEMORY INFO
DELETE
A SPEAKERS B AM/FM/DB TUNER MODE LISTEN MODE
11 12 13 14
11 12 13 14
6 7
6 7
a SOURCE
TONE TONE DEFEAT FRONT INPUT/MP
A
15 16 17
15 16 17
AM/FM mode
Toggle [ENTER] button to switch between "Tune" and "Preset" mode.
Select "Tune" mode.
• Pressing momentarily the [a/s] button will manually scan the AM
or FM band.
• Press and hold [a/s] for more than 2 seconds to search up or down;
the T 787's tuner will stop at the next sufficiently strong signal it
encounters.
• Note that this function "wraps" - that is, it will continue to search
from one end of the AM or FM band to the other until it stops at a
strong signal.
Toggle [ENTER] button to switch between "Tune" and "Preset" mode.
Select "Preset" mode.
• Use [d/f] to step up or down AM/FM Presets. Unused presets are
skipped over. Note that Presets must have been previously stored.
Refer also to the item about STORING PRESETS (AM/FM/XM/DAB) at the
LISTENING TO AM/FM RADIO section of the OPERATION page.
XM mode (120V version model only)
• Use the front panel [d/f] and [ENTER] buttons in combination
with the [MENU] button to select through applicable XM menu
options.
DAB mode (230V version model only)
• Use front panel [a/s] and [ENTER] buttons in combination with
[MENU] button to select through applicable DAB menu options.
4 MEMORY
• Press this button to store tuned AM, FM and digital radio stations to
the T 787's 40 preset-memory locations. One can store a mix of any
AM, FM and digital radio stations to the 40 available presets.
5 INFO
• Show information as supplied by the applicable source.
• Toggle [INFO] button to display supplied information.
8 9
8 9
VOLUME
s
B C D E
© NAD T 787
18 19
18 19