Panasonic CS-C9CKPG Service Manual page 25

NAME OF EACH PART
I Remote Control
1
2
AUTO HEA AUT HEAT COOL COOL DR DRY FAN AN
AUTO
ON
AUTO
OFF
FAN
TEMP
3
OFF/ON
QUIET
4
5
MODE ECONOMY POWERFUL
6
AIR SWING
AUTO MANUAL
FAN SPEED
7
1 2 3
8
ON SET
9
OFF CANCEL
TIMER
0
CHECK RESET CLOCK
G Remote Control Signal
• Make sure it is not obstructed.
• Maximum distance : 10 m (32.8 ft.).
• Signal received sound :
One short beep or one long beep.
G Notes for Remote Control
• Do not throw or drop.
• Do not get it wet.
• Certain types of fluorescent lamps may affect
signal reception. Consult your dealer.
PREPARATION BEFORE OPERATION
I Indoor Unit
1
5
2
4 3
1
Open the front panel
AUTO HEAT COOL DRY FAN
AUTO
2
Remove the air filters
3
Fit the air purifying filters in place
AUTO
FAN
4
Insert the air filters
5
Close the front panel
I Remote Control – To set the current time
AIR SWING
AUTO MANUAL FAN SPEED
1 2 3
ON SET
OFF
CANCEL
2
TIMER
1
CHECK RESET CLOCK
1 Press 1.
2 Then press 2 to increase or decrease the time.
3 Press 1 again.
Set time on display will light up.
1 Signal Transmitter
2 Operation Display
3 Quiet Mode Operation Button
4 Room Temperature Setting Button
(Illuminating button)
5 Operation Mode Selection Button
6 Economy Mode Operation Button
7 Auto Airflow Direction Button
!
8 ON-Timer Button
#
9 OFF-Timer Button
$
0 Reset Point
$
(Press with fine-tipped object to clear the memory)
%
! OFF/ON Button
^
(Illuminating button)
&
*
@ Powerful Mode Operation Button
(
# Fan Speed Selection Button
$ Manual Airflow Direction Selection Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
HOW TO OPERATE
2
3
5
I To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
I Setting Mode
• Press 2 to select:-
Cooling Model
AUTO – Automatic Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Air Circulation Operation
Heat Pump Model
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
25
CS-C9CKPG CU-C9CKP6G / CS-C12CKPG CU-C12CKP6G
G How to Insert the Batteries
2
1
Slide down the remote control cover completely
to remove it.
2
Insert the batteries
– Be sure the direction is correct
– 12:00 on display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
3
Re-install the remote control cover by inserting it
in the side groves and pushing inward.
G About the batteries
• Can be used for approximately one year.
G Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
I Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 60°F ~ 86°F.
• Recommended temperature:
Cooling Model
COOL –> 75°F ~ 78°F
DRY –> 2°F ~ 4°F
lower than the
1
room temperature
6
4
• During AUTO Operation, press 3 to select:-
• Operation with 4°F higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 4°F lower than the standard
temperature.
G Standard Temperature
Cooling Model
Indoor
Operation
temperature
Cooling
73°F Soft Dry
• Once the Automatic Operation is selected, the indoor
temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.
• After the operation mode has been selected, the
mode does not change.
Heat Pump Model
Indoor
temperature Operation
Cooling
Soft Dry
73°F
68°F
Heating
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.
1
Heat Pump Model
COOL –> 75°F ~ 78°F
DRY –> 2°F ~ 4°F
lower than the
room temperature
HEAT –> 68°F ~ 75°F
Standard
temperature
77°F
72°F
Standard
temperature
77°F
72°F
70°F