Related Manuals for Packard Bell Packard Bell EasyNote T5 series
Summary of Contents for Packard Bell Packard Bell EasyNote T5 series
- Page 1 EasyNote T5 series Disassembly Manual NEC Computers International B.V. EasyNote T5 series Disassembly Manual Revision: 2.0 Date: September 2003 For Packard Bell A division of NEC Computers International B.V.
-
Page 2: Table Of Contents
Table of contents Overview..................................3 Technician Notes ................................3 Disassembly Instructions..............................3 Reassembly Instructions ..............................3 Required Tools................................3 Hazardous Voltage ...............................3 Avoid Electrostatic Discharge ............................3 Power Supply Unit ................................3 Removing the Battery ..............................3 Removing the Hard Disk Drive.............................3 Removing the MDC Modem Module ...........................3 Removing the Keyboard Cover............................3 Removing Keyboard ..............................3 Removing the Optical drive &... -
Page 3: Overview
Packard Bell reserves the right to make changes to the EasyNote T5 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. -
Page 4: Hazardous Voltage
WARNING Hazardous Voltage Ensure that the computer is disconnected from its power source and from all There is hazardous voltage present inside the computer telecommunications links, networks, or modem when it is connected to an AC supply, even when the lines whenever the chassis cover is removed. -
Page 5: Removing The Battery
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the EasyNote T5 first. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. -
Page 6: Removing The Mdc Modem Module
Fig. 3 Disconnecting the hard disk drive 3. Unscrew the four screws on both sides of the hard disk drive as shown in Fig. 4 M3x4 Black Fig. 4 Unscrewing the hard disk drive bracket screws Removing the MDC Modem Module To remove the MDCmodem module, first remove the hard disk drive (see Removing the Hard Disk... -
Page 7: Removing The Keyboard Cover
Removing the Keyboard Cover To remove the Keyboard Cover , first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screw as shown in Fig. 6 M2x15 Black Fig. 6 Removing Keyboard Cover screws 2. -
Page 8: Removing The Optical Drive & Heat Plate
1. Remove the screws as shown in Fig. 8 M2.5x11 Black Fig. 8 Removing the screws holding the keyboard Note: The screw “A” located on the hard disk slot cover holds the hard disk drive and the keyboard. 2. Carefully lift up the keyboard. 3. - Page 9 M2.3 x 6 Sliver Fig. 10 Removing the screws on Heat Plate Note: If you want to disassemble the Optical Drive, you are required to release Screw “A” only. 2. Push the Optical Drive module out from the base unit as shown in Fig. 11 Fig.
-
Page 10: Removing The Memory Module
Fig. 12 Removing Heat plate from base unit Note: When assembling the heat plate, make sure that these three hocks on the heat plate are properly inserted into the openings located on the top cover. Removing the Memory Module To remove the memory module, first remove the Keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the... -
Page 11: Removing Heat Sink & Cpu
Removing heat plate), then perform the following steps: 1. Disconnect the wireless antenna connectors as shown in Fig. 14 Fig. 14 Disconnecting the wireless antenna Note: You might consider disconnecting the touch pad flat cable before removing the wireless module. 2. -
Page 12: Removing The Lcd Module
Fig. 16 Removing the heat sink 3. Use flat screws driver to release the CPU from the CPU socket; carefully lift up the CPU and put it in a safe place. Fig. 17 Releasing the CPU Removing the LCD Module To remove LCD Module, first remove the Keyboard Cover (see Removing the keyboard cover) - Page 13 shown in Fig. 18 M2.5x11 Black Fig. 18 Disconnecting the LCD & speaker connectors 2. Remove the LCD cable cover with a small flat screws driver as shown in Fig. 19 . Fig. 19 Removing the LCD cable Cover 3. Release the screws at rear side of the unit as shown in Fig. 20 Packard Bell EasyNote T5 Disassembly Manual Page 13...
-
Page 14: Removing The Lcd Panel
Fig. 20 LCD hinge screws at the rear M2x6 Black 4. Unscrew the two screws located on the bottom of the unit as shown in Fig. 21 M2x6 Black Fig. 21 LCD hinge screws at the bottom 5. Carefully lift the LCD module out of the system and put it aside. Removing the LCD Panel To remove the LCD Panel, first remove the LCD Module (see Removing the LCD... - Page 15 A = M2x3.5 Silver B= M2x5 Silver Fig. 22 Screws on the LCD Module Relase the LCD Bezel carefully and put it aside as shown in Fig. 23 Fig. 23 Removing the LCD Bezel 3. Unscrew all screws encircled in Fig. 24 disconnect the inverter board and put it aside. Packard Bell EasyNote T5 Disassembly Manual Page 15...
-
Page 16: Removing The Top Cover
M2x5 Silver Fig. 24 Removing the inverter board screws M2x3.5 Silver 4. Carefully lift up LCD panel and disconnect the LCD cable from the penal. 5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. - Page 17 To remove the Top Cover, first remove the Keyboard Cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove the LCD module (see Removing the Module) then perform the following steps: A = M2x6 Black 1. Disconnect the MIC connector on the DC/DC board. 2.
-
Page 18: Removing The Touch Pad
Fig. 28 Battery Compartment 5. Carefully lift up and release the top cover and put it aside. Fig. 29 Removing the top cover Note: Remember to disconnect the touch pad cable before lifting up the top cover. On the VGA connector area use extra care to release the top cover. -
Page 19: Removing The Dc/Dc Board
1. On the other side of the top cover unscrew the two screws on the Touch Pad assembly as shown in Fig. 30 and remove the Touch Pad assy from the palm rest. M2x3.5 Silver Fig. 30 Touch Pad Assembly Removing the DC/DC Board To remove the DC/DC board, first remove the Top Cover (see Removing the Top... -
Page 20: Removing The Main Board
M2.5x11 Black Fig. 31 DC/DC Board 2. Carefully remove the DC/DC board as shown in Fig. 32 and put it aside. Fig. 32 Removing the DC/DC Board Removing the Main Board To remove the Main board, first open the Top Cover (see Removing the Top Cover), remove DC/DC board (see... - Page 21 A = M2x5 Silver B = M2.5x8 Silver Fig. 33 Removing the main board screws M2.5x10 silver 2. Disconnect the VGA connector from the base as shown in Fig. 34 Fig. 34 Disconnecting the VGA connector 3. Lift the main board out of the system and put it aside (Fig. 35 ). Packard Bell EasyNote T5 Disassembly Manual Page 21...
-
Page 22: Dip Switch Setting
Fig. 35 Removing Main Board DIP Switch Settings Dip Switch Description Seeting Bit1 Keyboard Refer to the below table Select1 Bit2 Keyboard Refer to the below table Select2 Bit3 Reserved Reserved Bit4 BIOS Crisis ON : Enable OFF: Normal (Default) ON : connect to GND Bit5 DVDSEL... -
Page 23: Screws
Screws M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver M2.5x11 Black M2.5x12.5 Silver M2.5x15 Black M2x3 Sliver M2x6 Black M3x4 Black M2.5x5 Sliver Packard Bell EasyNote T5 Disassembly Manual Page 23... -
Page 24: Notice
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International BV. NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...