Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Packard Bell EasyNote L
Summary of Contents for Packard Bell EasyNote L
- Page 1 Packard Bell EasyNote L Disassembly Manual...
-
Page 2: Table Of Contents
Removing the LCD Module Removing the LCD Panel Removing the CPU Removing the Top Cover Removing the Touchpad Removing the Chipset Heat Sink Removing the WLAN Card Removing the MDC Modem Removing the Main Board Notice Packard Bell EasyNote L Disassembly Manual... -
Page 3: Overview
This document contains step-by-step service instructions for the EasyNote L. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Packard Bell reserves the right to make changes to the EasyNote L without notice. Technician Notes Only technicians authorized by NEC Computers International B.V. -
Page 4: Hazardous Voltage
Non personal injury. Always return a defective power avviare il sistema senza aver prima messo supply to your dealer. a posto il coperchio. Packard Bell EasyNote L Disassembly Manual... -
Page 5: Removing The Battery
Removing the Battery Perform the following steps to remove the battery: Make sure to power off the EasyNote L. Disconnect the AC adapter and all peripherals. iii. Turn the unit over. iv. Unlock the battery and slide it out. Fig. 1 Releasing the battery. -
Page 6: Removing The Hard Disk Drive
3. Carefully pull the Mylar to slide the hard disk drive assembly out of the bay. Fig. 5 Removing the HDD assembly. Removing the Keyboard To remove the keyboard, first remove the battery (see Removing the Battery), then perform the following steps: Packard Bell EasyNote L Disassembly Manual... - Page 7 Set the flat cable connector on the main board in the unlocked position (#1, Fig. Remove the keyboard cable from the keyboard connector on the main board (#2, Fig. Fig. 8 Disconnecting the keyboard flat cable. Packard Bell EasyNote L Disassembly Manual...
-
Page 8: Removing The Optical Disk Drive
To remove the LCD module, first remove the battery (see Removing the Battery), remove the keyboard (see Removing the Keyboard), then perform the following steps: 1. Remove the 6 screws securing the heat plate. Packard Bell EasyNote L Disassembly Manual... - Page 9 4. Open up the LCD and gently disconnect the LCD power cable and the 2 WLAN antenna cables. Fig. 15 Location WLAN antenna cables and LCD power cable. Note The black WLAN antenna cable is on the connector, the grey one on the connector. MAIN Packard Bell EasyNote L Disassembly Manual...
-
Page 10: Removing The Lcd Panel
Fig. 18 Removing the LCD panel hinges. Removing the CPU To remove the CPU first remove the battery (see Removing the Battery) and remove the keyboard (see Removing the Keyboard), then perform the following steps: Packard Bell EasyNote L Disassembly Manual... - Page 11 3. Remove the 3 remaining screws on the CPU heat sink and take it out. Fig. 20 Location remaining CPU heat sink screws. 4. Unlock the CPU socket by turning captured screw head fully counter clockwise with a flat- bladed screwdriver. Fig. 21 Removing the CPU. Packard Bell EasyNote L Disassembly Manual...
-
Page 12: Removing The Top Cover
2. Flip over and open up the notebook completely so that the LCD is levelled with the bottom of the casing. 3. Release all screws (2 large and 3 smaller ones) on the top cover. Packard Bell EasyNote L Disassembly Manual... -
Page 13: Removing The Top Cover
5. Carefully lift the top cover. Removing the Touchpad To remove the touchpad, first remove the top cover (see Removing the Top Cover), then perform the following steps: 1. Remove the screws securing the touchpad to the top cover. Packard Bell EasyNote L Disassembly Manual... -
Page 14: Removing The Chipset Heat Sink
1. Release with your fingers the side locks securing the WLAN card. As you release the locks, the card will automatically pop up and stay in a 45º angle position. Packard Bell EasyNote L Disassembly Manual... -
Page 15: Removing The Mdc Modem
Removing the Top Cover) and then perform the following steps: 1. Remove the hex screws from the VGA port. 2. Remove all screws on the HDD holder and separate it carefully from the main board. Packard Bell EasyNote L Disassembly Manual... - Page 16 3. Disconnect the speaker and Lid switch connectors from the main board and remove the screws encircled in the following picture. Fig. 30 Screws and connectors on main board. 4. Lift the main board and remove it away from the unit. Fig. 31 Removing the main board. Packard Bell EasyNote L Disassembly Manual...
-
Page 17: Notice
DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. Copyright © 2005 NEC Computers International B.V. All rights reserved. Packard Bell is a trademark of NEC Computers International B.V. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners.