Registered Parameter Number; Non-Registered Parameter Number - Yamaha QY100 Service Manual

QY100
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Sets the VOICE RECEIVE CHANNEL
to OMNI OFF and CHANNEL = 1.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Does not set OMNI ON. Sets the
VOICE RECEIVE CHANNEL to OMNI ON.
(3-2-6) MONO (CONTROL NUMBER = 7EH , DATA VALUE = 0)
Performs the same processing as when All SOUND OFF is received, and if the 3rd byte (mono number) is
in the range 0—16, sets the corresponding channel to Mode 4 (m=1).
If in the VOICE MODE, Mode 2 (m=1) is also possible, according to the VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH , DATA VALUE = 0)
Performs the same processing as when ALL SOUND OFF is received, and sets the corresponding
channel to Mode 3.
When in the VOICE MODE, Mode 1 is also possible, according to the VOICE RECEIVE CHANNEL.

(3-3) REGISTERED PARAMETER NUMBER

STATUS
LSB
RPN LSB
MSB
RPN MSB
DATA ENTRY MSB
DATA VALUE
DATA ENTRY LSB
DATA VALUE
First transmit an RPN MSB and RPN LSB to specify the parameter that is to be controlled, then use Data
Entry to set the value of the specified parameter.
RPN
LSB MSB
00H 00H
01H 00H
02H 00H
7FH 7FH

(3-4) NON-REGISTERED PARAMETER NUMBER

STATUS
LSB
RPN LSB
MSB
RPN MSB
DATA ENTRY MSB
DATA VALUE
First transmit an NRPN MSB and NRPN LSB to specify the parameter that is to be controlled, then use
Data Entry to set the value of the specified parameter.
NRPN
MSB LSB
01H 08H
01H 09H
01H 0AH
50
1011nnnn (BnH)
01100100 (64H)
0ppppppp
01100101 (65H)
0qqqqqqq
00000110 (06H)
0mmmmmmm
00100110 (26H)
0lllllll
D.ENTRY
MSB LSB PARAMETER NAME
mmH — PITCH BEND SENSITIVITY
mmH llH MASTER FINE TUNE
mmH — MASTER COARSE TUNE
— — RPN RESET
1011nnnn (BnH)
01100010 (62H)
0ppppppp
01100011 (63H)
0qqqqqqq
00000110 (06H)
0mmmmmmm
D.ENTRY
MSB LSB PARAMETER NAME
mmH — VIBRATO RATE
mmH — VIBRATO DEPTH
mmH — VIBRATO DELAY
n = 0 ~ 15 VOICE CHANNEL NUMBER
p = RPN LSB (Refer to the table on the following page.)
q = RPN MSB (Refer to the table on the following page.)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 24 semitones)
{mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
28H - 40H - 58H (-24 - 0 - +24 semitones)
Set to a condition in which the RPN number is
unspecified.
Internal settings will not change.
n = 0 ~ 15 VOICE CHANNEL NUMBER
p = NRPN LSB (Refer to the table on the following page.)
q = NRPN MSB (Refer to the table on the following page.)
m = Data Value
DATA RANGE
00H - 40H - 7FH (-64 - 0 - +63)
00H - 40H - 7FH (-64 - 0 - +63)
00H - 40H - 7FH (-64 - 0 - +63)