Page 1
Yes, you can. ® Invacare® Storm & Storm X-plore Power wheelchair User manual...
Page 3
How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
Page 4
+44 (0)1656 77 62 20 Pencoed uk@invacare.com Bridgend CF35 5AQ WWW: www.invacare.co.uk United Kingdom Invacare Mecc San s.r.l. +39 0445 38 00 59 Via dei Pini, 62 Fax: +39 0445 38 00 34 I - 36016 Thiene (VI) italia@invacare.com ITALIA WWW: www.invacare.it...
Table of Contents Chapter Page Introduction Important symbols in this manual ..................13 Important symbols found on the vehicle ................15 1.2.1 Explanation of symbols on lifter warning sticker............18 Type classification and permissible use................19 Indications..........................19 Usability............................20 Warranty ...........................21 Life expectancy........................21 Safety notes General safety notes .......................22 Safety information with regard to care and maintenance ...........25 Safety information on electromagnetic interference ............26...
Page 7
Information about getting in and out..................37 Using the cane holder ......................38 Driving Before driving for the first time....................39 Parking and stationary......................40 Taking Obstacles........................40 6.3.1 Maximum obstacle height .....................40 6.3.2 Safety information when ascending obstacles .............40 6.3.3 The correct way to overcome obstacles ...............41 Driving up and down gradients....................42 Using foldable antitipper wheels ...................43 Use on public roads ........................45...
Page 8
9.3.3 Adjusting the width of the travelling armrests ...............57 9.3.4 Adjusting the mobility of the travelling armrests ............59 9.3.5 Adjusting the arm support positions for the travelling armrests........60 Adjusting the seat angle ......................62 9.4.1 Electric ..........................62 9.4.2 Manual ..........................62 Adjusting the backrest......................64 9.5.1 Adjusting the backrest (standard seat) .................64 9.5.2...
Page 9
9.11.1.1 Exploded drawing of seat support ................82 9.11.2 Adjusting the seat depth ....................84 9.11.2.1 Exploded drawing of seat support ................86 9.11.2.2 Adjusting the seat depth without replacing the seat support plate ......87 9.11.2.3 Adjusting the seat depth with replacing the seat support plate .......88 9.12 Backrest unit with ergonomic length compensation (Easy-Adapt) ........90 9.12.1 Adjusting the width......................90...
Page 10
10.2.2.3 Setting the end stop of the legrest.................117 10.2.2.4 Adjusting the length of the legrest .................121 10.2.2.5 Adjusting the depth of the calf plate ..............122 10.2.2.6 Adjusting the height of the calf pad ...............123 10.2.2.7 Unlocking and swivelling the calf plate backward when alighting ......124 10.2.2.8 Adjusting the angle adjustable foot plate...............125 10.2.2.9...
Page 11
13.2 Use of the wheelchair as a seat in a vehicle...............159 13.2.1 Using the Invacare® Docking Station to anchor an electric wheelchair in a transport vehicle.........................161 13.2.2 How the wheelchair is anchored in a vehicle for use as a vehicle seat .....162 13.2.3 How the user is secured within the wheelchair............163...
The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.
Some maintenance and settings can be performed by the user or his/hers attendants. Certain adjustments do however require technical training and may only be carried out by your Invacare® specialist dealer. Damages and errors caused by nonobservance of the user manual or as a result of incorrect maintenance are excluded from all guarantees.
Page 14
BURN Risk! This symbol warns of the risk of burns, for example, as a result of hot motor surfaces. • Follow the instructions in order to avoid injury or damage to the product. RISK OF CRUSHING! This symbol warns of a risk of crushing caused by being careless with heavy components.
Requirements: • This symbol identifies a list of various tools, components and items which you will need in order to carry out certain work. Please do not attempt to carry out the work if you do not have the listed tools available. READ WELL BEFORE OPERATION! This symbol advises you to read information carefully.
Page 16
This symbol indicates the “Push” position of the coupling lever. In this position the motor is disengaged and the motor brakes are not operational. The wheelchair can be pushed by an attendant and the wheels turn freely. • Please note that the control panel must be switched off. •...
Page 17
• Please always make sure that the wheelchair is equipped with a headrest approved by Invacare before using it as a vehicle seat! This symbol indicates the maximum width to which an armrest may be adjusted. Pulling the armrest out further can cause it to fall out of it's fixation.
1.2.1 Explanation of symbols on lifter warning sticker Do not lean out Do not drive up Do not allow any Never drive with Never drive over when the lifter is or down slopes body parts to get two people! uneven surfaces raised! when the lifter is under a raised...
Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still in terms of their eyesight and physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).
• You should immediately stop using your power wheelchair if its usability is restricted due to: - brake failure • You should immediately contact an authorised Invacare® dealer if the usability of your power wheelchair is restricted due to: - the lighting system failing or being defective...
- unusual sounds developing or occurring Or if you have the feeling that something is wrong with your wheelchair. Warranty The terms and conditions of the warranty are part of the general terms and conditions particular to the individual countries in which this product is sold. Life expectancy We estimate a life expectancy of five years for this product, provided it is used in strict accordance with the intended use as set out in this document and all maintenance and service requirements...
Safety notes READ WELL BEFORE OPERATION! General safety notes Danger of injury if mobility device is used in any other way than the purpose described in this manual! • Only ever use the mobility device in accordance with the instructions in this User's Manual (see chapter "Type classification and permissible use"...
Page 23
Danger of injury if the mobility device is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt. (refer to the joystick operating manual for more information).
Page 24
Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your mobility device that are not expressly certified by Invacare® for this purpose. Have all electrical installations done by your authorised Invacare® Dealer.
Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! • For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric mobility product undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions).
Safety information on electromagnetic interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones can influence the functions of electric vehicles.
Safety information on driving and freewheel mode Danger of injury if the wheelchair tips over! • Inclines and declines can only be travelled up to the maximum safe slope (see chapter "Technical specifications" from page 175). • Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes.
Page 28
Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...
EEC / MPG (Medical Devices Act) and only applies to the complete product. The CE marking is invalidated if components or accessories are replaced or added that have not been approved for this product by Invacare. In this case, the company that adds or replaces the components or accessories is responsible for the conformity assessment/ CE marking or for registering the wheelchair as a special design and for the relevant documentation.
Page 30
• Only use seating systems that have been approved by Invacare® for this power wheelchair. Electrical and electronic components which have not been approved by Invacare® for use with this mobility aid can cause fire hazards and lead to electromagnetic damage! •...
Safety information on wheelchairs with a lifter WARNING! Danger of injury by moving parts! • Never let objects get caught in the space underneath a raised lifter! • Make sure that neither you nor anyone else is injured by placing hands, feet other body extremities under the raised seat! •...
Page 32
CAUTION! Damage to mobility aid caused by one-sided loading on lifter pillar! • One-sided loading occurs if the seat is raised and/or tilted. Always return your seat backrest to the upright position and the seat tilting to the horizontal position before ascending slopes! ! Never subject the lifter pillar to continuous single-sided loading! The raising and tilting function of the seat only provides additional rest positions.
Safety Information on Wheelchairs with Recaro Seats Danger of injury if the wheelchair tips over! The centre of gravity of a Recaro seat is higher than that of other seats. The Recaro seat is also heavier than other seating systems. The backrests of RECARO seats can be leaned back 90°.
The position of the labels on the product 1) Note: Remove the table before transporting 2) Identification of the lashing eyes at the front and back Warning that the wheelchair may not be used as a vehicle seat Note on required head support if the wheelchair may be used as a vehicle seat 3) Warning regarding the use of the lifter 4) Identification of the position of the coupling...
Getting in and out of the wheelchair Important information for getting into and out of the wheelchair from the side! The armrest must be removed in order to get into or out of the wheelchair from the side. Removing the armrests to get in If you want to get out on the side where the remote is installed, you can disconnect the remote cable from the remote (depending on your version).
Information about getting in and out Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the manual wheel lock of your wheelchair (if existing). •...
Using the cane holder If your mobility device is fitted with a cane holder, it can be used for the safe transport of a walking cane, underarm or forearm crutches. The cane holder consists of a plastic container (bottom) and a Velcro fastener (top).
Driving NOTE The maximum load capacity that is stated in the technical data only states that the system is designed for this mass in total. However, this does not mean that one can sit a person with this body weight in the wheelchair without restrictions. Attention must be paid to the body proportions, such as height, weight distribution, abdominal girth, leg and calf girth and seat depth.
• The rear mirror (if installed) is adjusted so you can look behind at all times without having to bend forward or shift your seating position. Parking and stationary When parking your vehicle or if your vehicle is stationary for a prolonged period: •...
ATTENTION: Risk of falling out of the chair and damage to the power wheelchair such as broken castors! • Never approach obstacles that are higher than the maximum climbable obstacle height. For the maximum climbable obstacle height, see "Technical specifications" on page 175. •...
Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical specifications" starting on page 175. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed. Avoid sudden changes of direction or abrupt braking when driving on slopes.
IMPORTANT INFORMATION ABOUT REGULATING THE ACTUATOR FUNCTIONS ON GRADIENTS Your mobility aid is fitted with an angular sensor which guarantees tipping stability. The sensor measures the actual angle of the drive unit, and prevents any further decrease in stability by restricting the functionality of the adjustment actuators.
Page 44
Folding the antitipper wheel down: Driving position • Pull out the locking pin (A), to release the antitipper wheel. • Fold the antitipper wheel down. Parking position The mobility device is now shorter.
If you wish to use your wheelchair on public roads and lighting is required by national legislation, then your wheelchair needs to be equipped with an appropriate lighting system. Please contact your Invacare ® dealer if you have any questions.
Pushing the mobility device in freewheel mode The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair manually whilst freewheeling, the magnetic brakes must be disengaged. NOTE: Pushing the wheelchair by hand may require more physical force than expected (more than 100 N).
Disengaging the motor: • Switch off remote. • Pull the engaging lever (1) upwards. The motor is disengaged. Engaging the motor: • Push the engaging lever down (1). The motor is engaged. Please note that both motors must always be engaged before driving! Remotes Your wheelchair may be equipped with one of several different remotes.
Adjusting the wheelchair to the user's seating posture CAUTION: Damage to wheelchair and accident hazard! It is possible that collisions can occur between wheelchair components due to various combinations of adjustment options and their individual settings! • The wheelchair is fitted with an individual, multiply adjustable seating system including adjustable legrests, armrests, a headrest or other options.
Adjustment possibility for control panel The following information is valid for all seating systems. CAUTION: Danger of the control panel being pushed backwards during an accidental collision with an obstacle, such as a doorframe or table, and the joystick being jammed against the armpad if the position of the control panel is adjusted and all screws are not completely tightened! This will cause the mobility device to drive forward uncontrollably and potentially injure the mobility device user and any person standing in the way!
9.1.2 Adjusting the height of the remote (only for foldable remote holders) Pre-requisites: • 1x 6 mm Allen key • Unscrew screw (1) with Allen key. • Adjust remote to required height. • Retighten the screw.
9.1.3 Swivelling the remote to the side If your wheelchair is fitted with a swing-away remote bracket, then the remote can be moved away to the side, for example to drive up close to a table.
Adjustment facilities for standard armrests 9.2.1 Changing the arm support position Requirements: • 1x Allen key 3 mm The arm support has 12 possible positions. • To change the position of the arm support, loosen the screw (1) and remove it. •...
9.2.2 Setting the height of the armrests Requirements: • Allen key 3 mm • Unscrew screw (1) with Allen key. • Adjust armrest to required height. • Retighten the screw.
9.2.3 Adjusting the width of the armrests WARNING! Serious injury hazard if one of the armrests falls out of its bracket because they have been adjusted to a width which exceeds the permissible value! • The width adjustment is fitted with small stickers with markings and the word "STOP"! The armrests must never be pulled out further than the point at which the word "STOP"...
Adjustment facilities for travelling armrests 9.3.1 Setting the height of the parallel sliding armrests The height of the travelling armrest is set using the armrest angle. • Release the knob to adjust the armrest angle (1). • Set the angle for the armrest. •...
9.3.2 Adjusting the angle of the armpad on the parallel sliding armrests Requirements: • Allen key 5 mm • Release the bolts to adjust the armrest angle (1) with the allen key. • Set the angle for the armrest. • Re-tighten the bolts. Make sure that the Nordlock washers used are re-inserted.
9.3.3 Adjusting the width of the travelling armrests The travelling armrests can be adapted to the backrest in eight widths. Pre-requisites: • 1x 4 mm Allen key • Undo the bolts on both sides of the backrest cover (1). The photograph only shows the bolts on the left- hand side.
Page 58
• Adjust the armrest width. The possible positions for the armrest are predefined by the drill-holes in the torque support and the armrest axel. • Insert the locating pin. • Retighten the screw. • Repeat the procedure for the other armrest. •...
9.3.4 Adjusting the mobility of the travelling armrests The flexibility of the travelling armrest can be adjusted to easier or stiffer. Requirements: • Allen key 5 mm • To make the armrest easier to move, release the bolt of the adjusting wrench (1) with the Allen key. •...
9.3.5 Adjusting the arm support positions for the travelling armrests Requirements: • Allen key 5 mm • Put the armrest in the vertical position. • Release the interior bolts (1) with the Allen key.
Page 61
• Position the armrest horizontally. • Re-tighten the bolts. Make sure that the Nordlock washers used are re-inserted.
Adjusting the seat angle CAUTION! Adjusting the seat tilt or the backrest angle changes the geometry of the mobility device and directly influences its dynamic stability! • For details regarding dynamic stability, negotiating gradients and obstacles and the correct adjustment of seat tilt or backrest angle, please see chapters "Taking Obstacles" on page 40 and "Driving up and down gradients"...
Page 63
• Switch the power supply off (ON/OFF key). • Unscrew Allen screws (1). • Adjust the seat angle by raising or lowering the seat. • Insert the Allen screws again and tighten.
Adjusting the backrest CAUTION! Adjusting the seat tilt or the backrest angle changes the geometry of the mobility device and directly influences its dynamic stability! • For details regarding dynamic stability, negotiating gradients and obstacles and the correct adjustment of seat tilt or backrest angle, please see chapters "Taking Obstacles" on page 40 and "Driving up and down gradients"...
9.5.2 Adjusting the back seat angle on the Easy-Adapt seating system 9.5.2.1 Electric Please consult the user manual for your remote for information about electrical adjustment. 9.5.2.2 Manual • Adjust the angle by turning the handwheel (1).
9.5.3 Adjusting the adaptable backrest padding There are two ways of adapting the backrest padding. • Using a snap buckle which is accessible without having to remove the backrest cushion. Please see Method 1. • With adjustment straps which are adjustable using Velcro. Please see Method 2. Method 1 •...
Page 67
Method 2 • Remove the backrest cushion (fixed with Velcro straps) by pulling it up and away so that you can access the adjusting straps. • Adjust the tension of the individual straps as required. • Replace the backrest cushion.
This can cause the neck to be hyperextended during collisions! • A headrest must be installed! The headrest optionally supplied for this mobility device by Invacare® is perfectly suitable for use during transport. • The headrest must be adjusted to the user's ear height.
9.6.1 Adjusting the position of the headrest or neckrest The adjustment of the position is the same for all headrests and neckrests. Pre-requisites: • Allen key 5 mm • Loosen the screws (1, 2) or the clamping lever (3). • Adjust the headrest or neckrest to the required position.
9.6.2 Adjusting the height of the headrest or neckrest The adjustment of the height is the same for all headrests and neckrests. • Loosen the thumb screw (1). • Adjust the headrest or neckrest to the required height. • Retighten thumb screw.
9.6.3 Adjusting the cheek supports • Push the cheek supports inward or pull them out to the required position. Postural belts A postural belt is an option which can either be fixed to the wheelchair ex-works or can be retrofitted by your specialist dealer. If your wheelchair is fitted with a postural belt, your specialist dealer will have informed you about fitting and usage.
9.7.1 Types of postural belts Your wheelchair can be fitted with the following postural belt types ex-works. If your wheelchair has been fitted with a different belt to those listed below, please ensure that you have received the manufacturer's documentation with regard to correct fitting and use. Belt with metal buckle, adjustable one side Belt can only be adjusted on one side which can result in the buckle not sitting centrally.
Page 73
If the belt is only fastened with a bolted connection, ensure that the connection has not loosened or undone. You can find more information about maintenance work on belts in the service manual, which is available from Invacare®.
Information regarding operation of the lifter at temperatures of less than 0 °C Invacare® mobility aids are fitted with safety mechanisms that prevent capacity overload of the electronic components. At operating temperatures below freezing point this can, in particular, lead to the lifter actuator being shut down after approx.
9.8.1 Explanation of symbols on lifter warning sticker Do not lean out Do not drive up Do not allow any Never drive with Never drive over when the lifter is or down slopes body parts to get two people! uneven surfaces raised! when the lifter is under a raised...
Adjusting the trunk support (Easy-Adapt seating system) The trunk supports can be adjusted in width, height and depth. 9.9.1 Adjusting the width • Loosen the handscrews (1). • Adjust the trunk support to the required width. • Retighten the handscrews again.
9.9.2 Adjusting the height Requirements: • Allen key 5 mm • Undo the height adjustment Allen screws (1). • Set the trunk support to the required height. • Retighten the screws.
9.9.3 Adjusting the depth Requirements: • Allen key 5 mm • Open the zip. • Undo the screws (1) for the depth adjustment. • Adjust the trunk support to the required position. • Retighten the screws. • Close the zip again.
9.10 Adjusting and removing the tray CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair. 9.10.1 Laterally adjusting the tray •...
9.10.2 Adjusting the depth of the tray / removing the tray • Loosen the wing-screw (1). • Adjust the table to the desired depth (or remove it entirely). • Re-tighten the screw. 9.10.3 Swinging the tray away to the side The tray can be swivelled up and away to the side to allow the user to get in and out of the mobility device CAUTION! Risk of injury! When the tray is raised it does not lock in place in this position!
The tray can be swivelled upwards and pushed to the side as illustrated to enable getting on and off. 9.11 Seat support 9.11.1 Adjusting seat width Note Please also refer to the following chapter entitled "Adjusting the seat depth". The seat width can be adjusted in stages between 380 and 530 mm. Requirements: •...
Page 83
• Remove the seat cushion. • Remove the cover plates (1). • Undo the two Allen screws (6) at the rear on the crossmember and remove them. • Undo the two Allen screws (9) at the front on the seat support plate and remove them. •...
9.11.2 Adjusting the seat depth Note Please also refer to the previous chapter entitled "Adjusting the seat width". The seat depthcan be adjusted in stages between 380 and 530 mm. Requirements: • 4 mm Allen key • 8 mm jaw spanner •...
Page 85
Seat depth Holes used in front seat Holes used in rear seat frame Seat support plate required in cm frame order no.: 1524550 order no.: 1524555 6 & 7 A & B SHORT 5 & 7 A & C order no. 1526437 4 &...
• Adjust the seat depth as described in the following chapter: - If the seat support plate does not need to be replaced, please refer to Chapter 9.11.2.2. - If the seat support plate does need to be replaced, please refer to Chapter 9.11.2.3. 9.11.2.2 Adjusting the seat depth without replacing the seat support plate •...
9.11.2.3 Adjusting the seat depth with replacing the seat support plate Disassembly: • Remove the legrests. • Remove the armrests. • Remove the seat cushion. • Remove any cable ties which hold cables from the remote or lighting which have been fitted. Remove the cables from any clips which have been glued on.
Page 89
• Insert the Allen screws (5) including washers again and tighten them. • If necessary, replace the seat support plate (2) in accordance with the table (see above). • Put the seat support plate (2) back in position. • Fit the two Allen screws (7) which are located at the front of the seat support, and connect them with the crossmembers (4).
9.12 Backrest unit with ergonomic length compensation (Easy-Adapt) 9.12.1 Adjusting the width Note Please also refer to the previous chapter entitled "Adjusting the seat width". The seat can be adjusted in width between 380 and 530 mm as standard. Requirements: •...
Page 91
• Loosen the three Allen screws (1). Do not, however, remove these screws completely. • Push the plate (2) as far as required until the required width in cm can be read off the scale (3). • Tighten the three Allen screws again. •...
These adjustments should only be carried out by trained specialists. Please contact your authorised Invacare specialist dealer. 9.13.1 Adjusting the suspension Adjusting the suspension harder •...
9.13.2 Adjusting the shock absorbance In the case of the Storm X-plore, the shock absorbance can be quickly and simply adjusted using a lever on the springs: • If you set the shock absorbance harder, you get a more direct response to the ground for more sportive driving with a less swinging chassis.
Page 94
The works setting for the lever is the middle position (1). From here, the shock absorbance can be adjusted harder or softer in four levels each.
Page 95
Adjusting the shock absorbance harder • Rotate the lever to the left to adjust the shock absorbance harder. • The fourth level (2) is the hardest shock absorbance. Adjusting the shock absorbance softer • Rotate the lever to the right to adjust the shock absorbance softer.
9.14 Adjusting or removing the luggage carrier CAUTION! Risk of damage as a result of collisions! Parts of the electric wheelchair may be damaged if the luggage carrier collides with the seat during seat angle or backrest adjustment. • Ensure that the luggage carrier is out of the range of both seat angle and backrest adjustment.
Your wheelchair can be fitted with the mini-adapter from the Rixen + Kaul KLICKfix system. To this you can attach various accessories such as the cellphone case supplied by Invacare, which you can use to transport your cellphone, sports glasses etc.
Page 98
The adapter can turn in 90° steps, allowing you to attach an accessory from any of four different directions. Please refer to the installation instructions which are available from your Invacare® dealer or directly from Invacare®. More information on the KLICKfix system is available at http://www.klickfix.com.
Adjusting footrests and legrests 10.1 Centre-mounted legrests 10.1.1 Electric legrest Please consult the user manual for your remote for information about electrical adjustment. The electric legrest can be lowered completely to assist getting out of the wheelchair. To do so, move your seat into the correct position by lowering the lifter or by means of a negative seat angle (tilted slightly to the front).
10.1.1.1 Lowering the electric legrest completely to assist getting out of the wheelchair Warning! Misuse may destroy the legrest. • Please read and carefully follow the instructions below. Getting in/out of the wheelchair • Set the lifter and tilt to a comfortable position. •...
Page 101
Lifting up the footplates • You are sitting in the wheelchair. • Put your feet beside the footplates. • Pull the lever (1). The footplates rise up automatically. • Let go the lever (1) and put your feet on the footplates.
Page 102
Warning! Danger of damage to the legrest! • Always make sure that the footplates are fully raised to the uppermost position before adjusting the angle of the legrest! • Disregarding this advice will cause damage to your legrest. Adjusting the legrest •...
10.1.2 Adjustable legrest 10.1.2.1 Adjusting the angle Prerequisites: • 1x 10 mm open-ended spanner • Use the open-ended spanner to loosen the counternut (1). • Move the legrest to the desired position by turning the spindle (2). • Tighten the counternut.
10.1.2.2 Adjusting the length of the legrest Prerequisites: • 1x 5 mm socket head spanner • Use the socket head spanner to loosen the fastening screws (1). • Slide the foot support to the desired height. • Tighten the fastening screws.
10.1.2.3 Adjusting the calf plate to the calf width of the user The calf plate of the legrest can be adapted to the user’s calf width by bending apart or together. • Bending the calf plate to the desired width.
10.1.2.4 Adjusting the angle of the foot plate Prerequisites: • 1x 5 mm socket head spanner • Fold up the foot plates in order to access the adjusting screws. • Use the socket head spanner to adjust the adjusting screws (1). •...
10.2 Legrests or footrests attached to the side 10.2.1 Vari-F footrest 10.2.1.1 Swivelling the footrest outward and/or removing The small unlocking button is located on the upper section of the footrest. When the footrest is unlocked, it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely.
10.2.1.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Requirements: •...
Page 109
• Loosen the screw (1) using the Allen key. • Set the desired angle. • Re-tighten the screw.
10.2.1.3 Setting the end stop of the footrest Pre-requisites: • 1x 6 mm Allen key • 1x 10 mm open-ended spanner The end position of the footrest is determined by means of a rubber stop (1). The rubber stop can be screwed in or out (A) or pushed up or down (B).
Page 111
• Use the Allen key to loosen the screw (1) and swivel the footrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
Page 112
• Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the screw.
10.2.1.4 Adjusting the length of the footrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...
10.2.2 Vari-A legrests 10.2.2.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.
10.2.2.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! •...
Page 116
• Loosen the fixing mechanism by tapping lightly against the handscrew. • Set the required angle. • Retighten the handscrew (1) again.
10.2.2.3 Setting the end stop of the legrest Pre-requisites: • 1x 10 mm open-ended spanner The end position of the legrest is determined by means of a rubber stop (A). The rubber stop can be screwed in or out (A) or pushed up or down (B).
Page 118
• Loosen the locking knob (1) counter-clockwise at least one turn. • Hit the knob to release the locking mechanism.
Page 119
• Swivel the legrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
Page 120
• Move the rubber stop to the desired position • Re-tighten the counternut • Move the legrest to the desired position. • Re-tighten the locking knob.
10.2.2.4 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...
10.2.2.5 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.
10.2.2.6 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.
10.2.2.7 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.
• Lift leg over the heel strap and place on the ground. 10.2.2.8 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...
10.2.2.9 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...
10.2.3 ADE legrests 10.2.3.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.
10.2.3.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! The electrically height-adjustable legrests are operated using the remote.
10.2.3.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...
10.2.3.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.
10.2.3.5 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.
10.2.3.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.
• Lift leg over the heel strap and place on the ground. 10.2.3.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...
10.2.3.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...
10.2.4 Angle-adjustable footboard Requirements: • Torx open-ended spanner T25 • Allen key 5 mm • Release the screws (1) with the Torx spanner and remove. • Adjust to required width. • Retighten the bolts. • Glue the anti-slip rubber mat to the footboard.
Page 136
• Loosen the locking screw(1) on both sides with the mm Allen key. • Adjust the footboard to the required angle. • Retighten the bolts.
NOTE A defective main fuse may be replaced only after checking the entire electric system. An Invacare® specialised dealer must perform the replacement. You can find information on the fuse type in chapter "Technical specifications" starting on page 175.
11.2 Batteries Power is supplied by two 12 V batteries. The batteries are maintenance-free and only need regular charging. In the following, you find information on how to charge, handle, transport, store, maintain, and use batteries. 11.2.1 Charging the batteries 11.2.1.1 General information on charging New batteries should always be fully charged once before their first use.
10 °C. • Use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements.
Risk of explosion and destruction of batteries if the wrong battery charger is used! • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®. Risk of electric shock and damage to the battery charger if it gets wet! •...
11.2.2 Storage and Maintenance Follow the instructions listed below to ensure safe use and longevity of the batteries: • Always store the batteries fully charged. • Do not leave the batteries in a low state of charge for an extended length of time. Charge a discharged battery as soon as possible.
Page 142
The last 3 LED (two red and one orange) mean a remaining capacity of about 15 %. • Driving with blinking red LED’s means an extreme stress for the battery and should be avoided under normal circumstances. • When only one red LED is blinking, the Battery Safe feature is enabled. From this time, speed and acceleration is reduced drastically.
• Under normal operation, once a month the battery should be discharged until all green and orange LED are off. This should be done within one day. A 16 hour charge afterwards is necessary as reconditioning. 11.2.4 Transporting batteries The batteries supplied with your electric vehicle are not hazardous goods. This classification is based on the German GGVS Hazardous Goods Road Transport Ordinances, and the IATA/DGR Hazardous Goods Rail Transport / Air Transport Ordinances.
Page 144
• Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.
Maintenance encompasses different areas, such as everyday care and cleaning, inspection checks, repair tasks and refurbishment. NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. 12.1...
12.2.1 Before each use of the mobility device Component Inspection If inspection is not passed Horn • • Check of correct mode of operation. Notify dealer Lighting unit • Check of correct operating mode for all • Notify dealer lights such as indicators, headlights and rear lights.
12.2.2 Weekly Component Inspection If inspection is not passed Armrests /side • • Check to ensure that the Tighten the screw or camping lever panels armrests can be correctly to fix the armrests (see chapter inserted in the holders and "Adjustment possibility for control panel"...
12.2.3 Monthly Item Inspection check Action All upholstered parts • • Check for damage and wear. Contact your dealer. Removable legrests • • Check whether the legrests can be fixed Contact your dealer. securely and whether the loosening mechanism is properly operable (see chapter "Adjusting footrests and legrests"...
"Technical specifications" on page 175, or consult the Service Manual, available from Invacare® (in this connection please see the addresses and phone numbers in section "How can you get in touch with Invacare®?" on page 3). In case you require assistance, please contact your Invacare® Dealer.
12.3.2 Repairing a flat tyre (front) Requirements: • Allen key 5 mm • Open-end spanner 24 mm • Repair kit for inner tubes or a new inner tube. • Talcum powder Remove the wheel • Jack the vehicle up and place a block of wood underneath it to prop it up.
Page 152
Repair the flat tyre EXPLOSION HAZARD! The wheel explodes if the air is not left out before dismantling! • It is imperative that you let the air out of the tyre before dismantling it (press the pin in the middle of the valve downwards)! •...
Page 153
• Place the rim halves in the tyre from the outside. • Pump up the tyre a little. • Re-position the Allen screws in the rim and tighten them firmly. Make sure the inner tube does not get pinched between the rims halves! •...
12.3.3 Repairing tyre punctures (drive wheel) Injury hazard! If the wheel has been insufficiently tightened during assembly, it can become loosened during driving! • When reassembling the drive wheels, tighten the Allen screws at a torque of 30 Nm! • Secure all screws using a suitable blocker (e.g. Loctite 243)! Requirements: •...
Page 155
NOTE Re-assembly is done in reverse order. Ensure that the tyre is replaced on the same side and in the same travel direction as it was previously mounted. Repairing the flat tyre EXPLOSION HAZARD! The wheel will explode if you do not let the air out of the tyre before removing the wheel! •...
Page 156
• Insert the wheel rim halves from outside into the tyre. • Pump a little air into the inner tube. • Reinsert the cylinder head screws and tighten to10 Nm. Avoid crushing the inner tube! • Ensure that the tyre outer is seated correctly. •...
Transport CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair.
13.1 Transferring the wheelchair to a vehicle WARNING: The wheelchair is in danger of tipping over if it is transferred to a vehicle while the driver is still seated in the wheelchair! • Transfer the wheelchair without the driver whenever possible! •...
Web: www.unwin-safety.com • An alternative way to safely use this wheelchair as a vehicle seat may be by using the Docking Station system if the wheelchair is compatible with that system, available separately! Please contact Invacare if you require the details.
Page 160
Caution: There is a danger of injury if the wheelchair is not properly secured during use as a vehicle seat! • If possible, the user should always leave the wheelchair to use a vehicle seat and the safety belts provided with the vehicle. •...
Alterations to the wheelchair anchoring points may not be carried out without the manufacturer's permission. 13.2.1 Using the Invacare® Docking Station to anchor an electric wheelchair in a transport vehicle Please see the Docking Station instruction manual for information about anchoring an electric...
13.2.2 How the wheelchair is anchored in a vehicle for use as a vehicle seat The power wheelchair is fitted with four anchoring points, which are labelled with the symbol shown on the right. Snap hooks or belt loops can be used for fixation.
13.2.3 How the user is secured within the wheelchair CAUTION: There is a danger of injury if the user is not properly secured within the wheelchair! • Even if the wheelchair is fitted with a postural belt, this is no substitute for a proper safety belt which complies with ISO 10542 in the transport vehicle.
Page 164
This can cause the neck to be hyperextended during collisions! • A headrest must be installed! The headrest optionally supplied for this mobility device by Invacare® is perfectly suitable for use during transport. • The headrest must be adjusted to the user's ear height.
Page 165
Seat belts may not be held at a distance The pelvic belt should be positioned in the from the user's body using parts of the area between the user's pelvis and thighs wheelchair such as armrests or wheels. so that it is unobstructed and not too loose. The ideal angle of the pelvic belt to the horizontal is between 45°...
Page 166
The safety belt installed in the transporting vehicle should be applied as shown in the illustration at right. 1) Centre line of the body 2) Centre of the sternum...
CAUTION: Injury hazard! ® • If you are unable to fasten your electric wheelchair securely in a transport vehicle, Invacare recommends that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.
13.3.1 Opening the rear cover Removing the rear cover: • Loosen and remove the two knurled screws (1) on the left and right side of the rear casing. • Lift the rear cover carefully. The front part of the cover is held at the top by a Velcro strip. This must also be released.
• Fit the parts in the reverse order. • Tighten the two knurled screws by hand. 13.3.2 Making the batteries accessible WARNING! Fire and burn hazard due to short circuit at battery poles! • DO NOT short-circuit the battery poles with a tool or metal parts of the wheelchair! •...
Page 170
• Remove the rear cover as described in chapter 13.3.1 • Pull the snap fitting (1) beside the power module backwards. • Lift the power module with the holder and remove the mounting from the battery cap flap. • Place the power module and the mounting on top of the battery compartment or actuator module, if applicable.
13.3.3 Removing/Installing the batteries Requirements: • 11-mm socket spanner Removing the batteries: • Make the batteries accessible as described in chapter 13.3.2 • Remove the pole caps (1) from the accessible battery (3). • Remove the pole screws located under the pole caps using an 11-mm socket spanner. •...
Page 173
• Lift the battery from the battery carrier. • Pull the second battery forward using its strap. • Disconnect the cables of the second battery as well. • Lift the second battery from the battery carrier. Fitting the batteries: • Fit the batteries in the reverse order. •...
• Cleaning and disinfection. Please see chapter "Maintenance" on page 145. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating posture" on page 48.
Technical specifications The technical information provided hereafter applies to a standard configuration or represents maximum achievable values. These can change if accessories are added. The precise changes to these values are detailed in the sections for the respective accessories. Permissible operating and storage conditions Temperature range for operation according to ISO 7176-9: •...
Page 176
Drive wheel tyres Tyre pressure The recommended maximum tyre pressure in bar or kpa is marked on the side wall of the tyre or the rim. If more than one value is listed, the lower one in the corresponding units applies. (Tolerance = -0.3 bar,1 bar = 100 kpa) Castor wheel tyres Tyre type...
Page 177
Dimensions Standard Easy-Adapt Matrix Recaro Total height • 970 mm • 1050 mm • 970 mm • 970 mm Drive unit width • 630 - 770 mm Total length (incl. standard • 1190 mm legrests) Total length (without standard • 910 mm legrests) Seat height *** (with lifter) •...
Page 178
*** Measured without seat cushion **** The actual kerb weight depends on the fittings your mobility aid has been supplied with. Every Invacare® mobility aid is weighed when leaving the works. Please refer to the nameplate for the kerb weight (including batteries) measured.
It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...