1. Manuals
  2. Brands
  3. Invacare Manuals
  4. Wheelchair
  5. Storm4 X-plore
  6. Instruction manual

Invacare Storm4 Instruction Manual

Power chair
Hide thumbs Also See for Storm4:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
Yes, You Can.®
4
Invacare® Storm
Mobility aid
Instruction manual

Advertisement

Table of Contents
loading

Related Manuals for Invacare Storm4

Summary of Contents for Invacare Storm4

  • Page 1 Yes, You Can.® Invacare® Storm Mobility aid Instruction manual...
  • Page 2 How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
  • Page 3 Bridgend Industrial Estate uk@invacare.com Mid Glamorgan - CF31-3PY eire@invacare.com United Kingdom WWW: www.invacare.co.uk Invacare Mecc San s.r.l. +39 - 0445 - 38 00 59 Via Dei Pini, 62 Fax: +39 - 0445 - 38 00 34 I - 36016 Thiene (VI) italia@invacare.com...
  • Page 4 +31 - (0)318 - 69 57 57 Celsiusstraat 46 Fax: +31 - (0)318 - 69 57 58 NL-6716 BZ Ede csede@invacare.com The Netherlands WWW: www.invacare.nl Invacare® PORTUGAL Lda +351-225105946 Rua Senhora de Campanhã 105 Fax: +351-225105739 P-4369-001 Porto portugal@invacare.com PORTUGAL WWW: www.invacare.pt...

  • Page 5: Table Of Contents

    Table of Contents Chapter Page Introduction Important symbols in this manual ..................12 Important symbols found on the vehicle ................13 Type classification and permissible use................15 Guarantee ..........................15 Indications..........................16 Life expectancy........................16 Safety Notes General Safety Notes ......................17 Safety information with regard to care and maintenance ...........20 Safety Information on Electromagnetic Interference............21 Safety Information on Driving and Freewheel Mode............22 Safety information regarding changes and modifications to the mobility device....24...
  • Page 6 Before driving for the first time....................32 Parking and stationary......................33 Taking Obstacles........................34 5.3.1 Maximum obstacle height .....................34 5.3.2 Safety information when ascending obstacles .............34 5.3.3 The correct way to overcome obstacles ...............34 Driving up and down gradients....................35 Pushing the mobility device in freewheel mode Disengaging motors........................37 Remotes Adjusting the wheelchair to the user's seating posture...
  • Page 7 8.4.1 Adjusting the position of the headrest or neckrest ............53 8.4.2 Adjusting the height of the headrest or neckrest ............54 8.4.3 Adjusting the position of the headrest with cheek support sideways ......55 8.4.4 Adjusting the cheek supports ..................56 Postural belts ...........................57 8.5.1 Types of postural belts....................57 8.5.2...
  • Page 8 9.1.2.1 Adjusting the angle ....................81 9.1.2.2 Adjusting the length of the legrest ................82 9.1.2.3 Adjusting the calf plate to the calf width of the user ..........83 9.1.2.4 Adjusting the angle of the foot plate ................84 Legrests or footrests attached to the side................85 9.2.1 Vari-F footrest .......................85 9.2.1.1...
  • Page 9 10 Electrical System 10.1 Electronics Protection System ....................114 10.2 Batteries ..........................115 10.2.1 What you need to know about batteries ..............115 10.2.2 Charging the batteries ....................117 10.2.3 How to handle damaged batteries correctly ...............118 11 Maintenance 11.1 Cleaning the mobility device ....................119 11.2 Inspection checks .........................120 11.2.1 Before each use of the mobility device...............121...

  • Page 10: Introduction

    The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.
  • Page 11 This manual contains copyrighted information. This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare® or its statutory representatives. We reserve the right to make any necessary alterations on the grounds of...

  • Page 12: Important Symbols In This Manual

    Important symbols in this manual WARNING! This symbol warns you of danger! • Always follow these instructions to avoid injury to the user or damage to the product! EXPLOSION HAZARD! This symbol warns you of an explosion hazard, an example of which can be caused by excessive tyre pressure in a pneumatic tyre! •...

  • Page 13: Important Symbols Found On The Vehicle

    Important symbols found on the vehicle This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/CE. This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are not appropriate according to legislation.
  • Page 14 If the electric wheelchair is fitted with a table, it is imperative that it is removed and safely stowed when transporting the wheelchair in a vehicle!

  • Page 15: Type Classification And Permissible Use

    Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).

  • Page 16: Indications

    Indications The use of this mobility product is recommended for the following indications: The inability or a greatly restricted ability to walk within the scope of the basic requirement to be able to move within one’s own four walls. The need to leave the dwelling place in order to get some fresh air during a short walk or to reach those places generally to be found at close distance to the dwelling and where everyday business is carried out.

  • Page 17: Safety Notes

    Safety Notes • READ WELL BEFORE OPERATION! General Safety Notes Danger of injury if mobility device is used in any other way than the purpose described in this manual! • Only ever use the mobility device in accordance with the instructions in this User's Manual (see Chapter "Type classification and permissible use"...
  • Page 18 Danger of injury if the mobility device is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt! (please Refer to the joystick operating manual for more information).
  • Page 19 Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your mobility device that are not expressly certified by Invacare® for this purpose! Have all electrical installations done by your authorised Invacare® Dealer!

  • Page 20: Safety Information With Regard To Care And Maintenance

    Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! • For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric mobility product undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions)! •...

  • Page 21: Safety Information On Electromagnetic Interference

    Safety Information on Electromagnetic Interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) Regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones, can influence the functions of electric vehicles.

  • Page 22: Safety Information On Driving And Freewheel Mode

    Safety Information on Driving and Freewheel Mode Danger of injury if the wheelchair tips over! • Inclines and declines can only be travelled up to the maximum safe slope (please see Chapter "Technical Specifications" from Page 134). • Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes! We recommend that you position the seat backrest and the seat tilt (if fitted) slightly to the rear before descending slopes! •...
  • Page 23 Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...

  • Page 24: Safety Information Regarding Changes And Modifications To The Mobility Device

    • Only ever use electrical and electronic components which have been authorised by Invacare® for this mobility aid! Batteries which have not been authorised by Invacare® for use with this mobility aid can cause chemical burns! • Only ever use batteries which have been authorised by Invacare® for this mobility aid!

  • Page 25: Safety Information On Wheelchairs With A Lifter

    Safety Information on Wheelchairs with a Lifter IMPORTANT - IF YOUR WHEELCHAIR IS EQUIPPED WITH A LIFTER: Danger of injury if the wheelchair tips over! • Never exceed the maximum permissible load (see Technical Specifications)! • Avoid dangerous driving situations when the lifter is in a raised position, such as trying to overcome obstacles like kerbs or driving up or down steep gradients! •...
  • Page 26 Important information regarding speed reduction with raised lifter! If the lifter has been raised above a certain point, the drive electronics considerably reduces the speed of the mobility aid. If speed reduction has been activated, drive mode can only be used to carry out minor movements of the mobility aid and not for regular driving! To drive normally, please lower the lifter until the speed reduction has been deactivated again!

  • Page 27: Safety Information On Wheelchairs With Recaro Seats

    Safety Information on Wheelchairs with Recaro Seats Danger of injury if the wheelchair tips over! The centre of gravity of a Recaro seat is higher than that of other seats. The Recaro seat is also heavier than other seating systems. The backrests of RECARO seats can be leaned back 90°.

  • Page 28: Key Features

    Key features 1) Headrest 2) Backrest 3) Armrest 4) Battery case (rear) 5) Drive wheel 6) Drive motor (with engaging lever) 7) Remote 8) Legrests 9) Castor wheel...

  • Page 29: Getting In And Out Of The Wheelchair

    Getting in and out of the wheelchair Important information for getting into and out of the wheelchair from the side! The armrest must be removed in order to get into or out of the wheelchair from the side. Removing the armrests to get in If you want to get out on the side where the remote is installed, you can disconnect the remote cable from the remote (depending on your version).

  • Page 30: Information About Getting In And Out

    Information about getting in and out Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the hand brake of your wheelchair (if existing). •...

  • Page 31: Using The Cane Holder

    Using the cane holder If your mobility device is fitted with a cane holder, then this can be used to safety transport your walking cane or crutches with you wherever you go. The cane holder consists of a lower plastic holder and an upper Velcro fastener.

  • Page 32: Driving

    Driving NOTE The maximum load capacity that is stated in the technical data only states that the system is designed for this mass in total. However, this does not mean that one can sit a person with this body weight in the wheelchair without restrictions. Attention must be paid to the body proportions, such as height, weight distribution, abdominal girth, leg and calf girth and seat depth.

  • Page 33: Parking And Stationary

    • The rear mirror (if fitted) is fitted so that you can always look behind you without having to lean forward or change your seat position in any way. Parking and stationary When parking your vehicle or if your vehicle is stationary for a prolonged period: •...

  • Page 34: Taking Obstacles

    Taking Obstacles 5.3.1 Maximum obstacle height You can find information about maximum obstacle heights in the chapter entitled "Technical Specifications" from page 134. 5.3.2 Safety information when ascending obstacles CAUTION: Danger of Tipping Over! • Never approach obstacles at an angle! •...

  • Page 35: Driving Up And Down Gradients

    Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical Specifications" starting on page 134. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed! Avoid sudden changes of direction or abrupt braking when driving on slopes! •...
  • Page 36 IMPORTANT INFORMATION ABOUT REGULATING THE ACTUATOR FUNCTIONS ON GRADIENTS Your mobility aid is fitted with an angular sensor which guarantees tipping stability. The sensor measures the actual angle of the drive unit, and prevents any further decrease in stability by restricting the functionality of the adjustment actuators.

  • Page 37: Pushing The Mobility Device In Freewheel Mode

    Pushing the mobility device in freewheel mode The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair manually whilst freewheeling, the magnetic brakes must be disengaged. NOTE: Pushing the wheelchair by hand may require more physical force than expected (more than 100 N).
  • Page 38 Disengaging the motor: • Switch off remote. • Pull the engaging lever (1) upwards. The motor is disengaged. Engaging the motor: • Push the engaging lever down (1). The motor is engaged. Please note that both motors must always be engaged before driving!

  • Page 39: Remotes

    Remotes Your wheelchair may be equipped with one of several different remotes. For information on the different functions and how to operate a particular remote, please see it's corresponding User Guide.

  • Page 40: Adjusting The Wheelchair To The User's Seating Posture

    Adjusting the wheelchair to the user's seating posture CAUTION: Damage to wheelchair and accident hazard! Collisions between the legrests and the chassis, or between the footplates and the floor, can occur due to different combinations of adjustment options! • When adjusting the seat angle, lifter and legrests, ensure that the legrests cannot collide with the wheelchair chassis, and that the footplates cannot collide with the floor! Electrical adjustment options Please refer to the instruction manual for your remote for more information on operating...

  • Page 41: Adjusting The Armrests And The Joystick Box

    Adjusting the armrests and the joystick box The following information is valid for all seating systems. CAUTION: Danger of the remote being pushed backwards during an accidental collision with an obstacle, such as a doorframe or table, and the joystick being jammed against the armpad if the position of the remote is adjusted and all screws are not completely tightened! This will cause the mobility device to drive forward uncontrollably and potentially injure the mobility device user and any person standing in the way!

  • Page 42: Adjusting The Height Of The Remote (Only For Foldable Remote Holders)

    8.1.2 Adjusting the height of the remote (only for foldable remote holders) Pre-requisites: • 1x 6 mm Allen key • Unscrew screw (1) with Allen key. • Adjust remote to required height. • Retighten the screw.

  • Page 43: Swivelling The Remote To The Side

    8.1.3 Swivelling the remote to the side If your wheelchair is fitted with a swing-away remote bracket, then the remote can be moved away to the side, for example to drive up close to a table.

  • Page 44: Changing The Arm Support Position

    8.1.4 Changing the arm support position Requirements: • 1x Allen key 3 mm The arm support has 12 possible positions. • To change the position of the arm support, loosen the screw (1) and remove it. • The position of the arm support is adjusted by selecting a combination of screw holes in the arm support and the drillholes in the fixing plate.

  • Page 45: Setting The Height Of The Armrests

    8.1.5 Setting the height of the armrests Requirements: • Allen key 3 mm • Unscrew screw (1) with Allen key. • Adjust armrest to required height. • Retighten the screw.

  • Page 46: Adjusting The Width Of The Armrests

    8.1.6 Adjusting the width of the armrests WARNING! Serious injury hazard if one of the armrests falls out of its bracket because they have been adjusted to a width which exceeds the permissible value! • The width adjustment is fitted with small stickers with markings and the word "STOP"! The armrests must never be pulled out further than the point at which the word "STOP"...

  • Page 47: Adjusting The Seat Angle

    Adjusting the seat angle CAUTION! Adjusting the seat tilt or the backrest angle changes the geometry of the mobility device and directly influences its dynamic stability! • For details regarding dynamic stability, negotiating gradients and obstacles and the correct adjustment of seat tilt or backrest angle, please see chapters "Taking Obstacles" on page 34 and "Driving up and down gradients "...
  • Page 48 • Switch the power supply off (ON/OFF key). • Unscrew Allen screws (1). • Adjust the seat angle by raising or lowering the seat. • Insert the Allen screws again and tighten.

  • Page 49: Adjusting The Backrest

    Adjusting the backrest CAUTION! Adjusting the seat tilt or the backrest angle changes the geometry of the mobility device and directly influences its dynamic stability! • For details regarding dynamic stability, negotiating gradients and obstacles and the correct adjustment of seat tilt or backrest angle, please see chapters "Taking Obstacles" on page 34 and "Driving up and down gradients "...

  • Page 50: Adjusting The Back Seat Angle On The Easy-Adapt Seating System

    8.3.2 Adjusting the back seat angle on the Easy-Adapt seating system 8.3.3 Electric Please consult the instruction manual for your remote for information about electric adjustment. 8.3.4 Manual • Adjust the angle by turning the handwheel (1).

  • Page 51: Adjusting The Tension Adjustable Backrest Upholstery

    8.3.5 Adjusting the tension adjustable backrest upholstery • Remove the backrest cushion (attached with Velcro strips) by pulling it up and off to access the adjustment straps. • Adjust the tension of the individual straps as desired. • Replace the backrest cushion.

  • Page 52: Adjusting The Headrest

    The neck can be hyperextended during collisions! • A headrest must be installed! The optionally available headrest supplied by Invacare® for this wheelchair is perfectly suitable for use during transport. Headrests from third-party manufacturers may also be used for this purpose.

  • Page 53: Adjusting The Position Of The Headrest Or Neckrest

    8.4.1 Adjusting the position of the headrest or neckrest The adjustment of the position is the same for all headrests and neckrests. Pre-requisites: • Allen key 5 mm • Loosen the screws (1, 2) or the clamping lever (3). • Adjust the headrest or neckrest to the required position.

  • Page 54: Adjusting The Height Of The Headrest Or Neckrest

    8.4.2 Adjusting the height of the headrest or neckrest The adjustment of the height is the same for all headrests and neckrests. • Loosen the thumb screw (1). • Adjust the headrest or neckrest to the required height. • Retighten thumb screw.

  • Page 55: Adjusting The Position Of The Headrest With Cheek Support Sideways

    8.4.3 Adjusting the position of the headrest with cheek support sideways Pre-requisites: • Allen key 5 mm • Loosen the Allen screw (1) • Slide the headrest left or right to the required position. • Retighten the Allen screw.

  • Page 56: Adjusting The Cheek Supports

    8.4.4 Adjusting the cheek supports • Push the cheek supports inward or pull them out to the required position.

  • Page 57: Postural Belts

    Postural belts A postural belt is an option which can either be fixed to the wheelchair ex-works or can be retrofitted by your specialist dealer. If your wheelchair is fitted with a postural belt, your specialist dealer will have informed you about fitting and usage. The postural belt is used to help the wheelchair user keep an optimum sitting position.

  • Page 58: Adjusting The Postural Belt Correctly

    If the belt is only fastened with a bolted connection, ensure that the connection has not loosened or undone. You can find more information about maintenance work on belts in the service manual, which is available from Invacare®.

  • Page 59: The Lifter

    The Lifter The electric lifter is operated from the remote. Please refer to the remote manual for more information. Information regarding operation of the lifter at temperatures of less than 0 °C Our wheelchairs are fitted with safety mechanisms that prevent capacity overload of the electronic components.

  • Page 60: Adjusting The Trunk Support (Easy-Adapt Seating System)

    Adjusting the trunk support (Easy-Adapt seating system) The trunk supports can be adjusted in width, height and depth. 8.7.1 Adjusting the width • Loosen the handscrews (1). • Adjust the trunk support to the required width. • Retighten the handscrews again.

  • Page 61: Adjusting The Height

    8.7.2 Adjusting the height Requirements: • Allen key 5 mm • Undo the height adjustment Allen screws (1). • Set the trunk support to the required height. • Retighten the screw.

  • Page 62: Adjusting The Depth

    8.7.3 Adjusting the depth Requirements: • Allen key 5 mm • Open the zip. • Undo the screws (1) for the depth adjustment. • Adjust the trunk support to the required width. • Retighten the bolts. • Close the zip again.

  • Page 63: Adjusting And Removing The Tray

    Adjusting and removing the tray CAUTION: Injury hazard or material damage if an electric wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair! 8.8.1 Laterally adjusting the tray •...

  • Page 64: Adjusting The Depth Of The Tray / Removing The Tray

    8.8.2 Adjusting the depth of the tray / removing the tray • Loosen the wing-screw (1). • Adjust the table to the desired depth (or remove it entirely). • Re-tighten the screw. 8.8.3 Swinging the tray away to the side The tray can be swivelled up and away to the side to allow the user to get in and out of the mobility device CAUTION! Risk of injury! When the tray is raised it does not lock in place in this position!
  • Page 65 The tray can be swivelled upwards and pushed to the side as illustrated to enable getting on and off.

  • Page 66: Seat Support

    Seat support 8.9.1 Adjusting seat width Note Please also refer to the following chapter entitled "Adjusting the seat depth". The seat width can be adjusted in stages between 38 and 53 cm. Requirements: • 4 mm Allen key...

  • Page 67: Exploded Drawing Of Seat Support

    8.9.1.1 Exploded drawing of seat support...
  • Page 68 • Remove the seat cushion. • Remove the cover plates (1). • Undo the two Allen screws (6) at the rear on the crossmember and remove them. • Undo the two Allen screws (9) at the front on the seat support plate and remove them. •...

  • Page 69: Adjusting The Seat Depth

    8.9.2 Adjusting the seat depth Note Please also refer to the previous chapter entitled "Adjusting the seat width". The seat depthcan be adjusted in stages between 38 and 53 cm. Requirements: • 4 mm Allen key • 8 mm jaw spanner •...
  • Page 70 Seat depth Holes used in front seat Holes used in rear seat frame Seat support plate required in cm frame order no.: 1524550 order no.: 1524555 6 & 7 A & B SHORT 5 & 7 A & C order no. 1526437 4 &...

  • Page 71: Exploded Drawing Of Seat Support

    8.9.2.1 Exploded drawing of seat support...

  • Page 72: Adjusting The Seat Depth Without Replacing The Seat Support Plate

    • Adjust the seat depth as described in the following chapter: - If the seat support plate does not need to be replaced, please refer to Chapter 8.9.2.2. - If the seat support plate does need to be replaced, please refer to Chapter 8.9.2.3. 8.9.2.2 Adjusting the seat depth without replacing the seat support plate •...

  • Page 73: Adjusting The Seat Depth With Replacing The Seat Support Plate

    8.9.2.3 Adjusting the seat depth with replacing the seat support plate Disassembly: • Remove the legrests. • Remove the armrests. • Remove the seat cushion. • Remove any cable ties which hold cables from the remote or lighting which have been fitted. Remove the cables from any clips which have been glued on.
  • Page 74 • Insert the Allen screws (5) including washers again and tighten them. • If necessary, replace the seat support plate (2) in accordance with the table (see above). • Put the seat support plate (2) back in position. • Fit the two Allen screws (7) which are located at the front of the seat support, and connect them with the crossmembers (4).

  • Page 75: Backrest Unit With Ergonomic Length Compensation

    8.10 Backrest unit with ergonomic length compensation 8.10.1 Adjusting the width Note Please also refer to the previous chapter entitled "Adjusting the seat width". The seat can be adjusted in width between 38 and 53 cm as standard. Requirements: • 4 mm Allen key •...
  • Page 76 • Loosen the three Allen screws (1). Do not, however, remove these screws completely. • Push the plate (2) as far as required until the required width in cm can be read off the scale (3). • Tighten the three Allen screws again. •...

  • Page 77: Adjusting Footrests And Legrests

    Adjusting footrests and legrests Centre-mounted legrests 9.1.1 Electric legrest Please consult the instruction manual for your remote for information about electric adjustment. The electric legrest can be lowered completely to assist getting out of the wheelchair. To do so, move your seat into the correct position by lowering the lifter or by means of a negative seat angle (tilted slightly to the front).

  • Page 78: Lowering The Electric Legrest Completely To Assist Getting Out Of The Wheelchair

    9.1.1.1 Lowering the electric legrest completely to assist getting out of the wheelchair Warning! Misuse may destroy the legrest. • Please read and carefully follow the instructions below. Getting in/out of the wheelchair • Set the lifter and tilt to a comfortable position. •...
  • Page 79 Lifting up the footplates • You are sitting in the wheelchair. • Put your feet beside the footplates. • Pull the lever (1). The footplates rise up automatically. • Let go the lever (1) and put your feet on the footplates.
  • Page 80 Warning! Danger of damage to the legrest! • Always make sure that the footplates are fully raised to the uppermost position before adjusting the angle of the legrest! • Disregarding this advice will cause damage to your legrest. Adjusting the legrest •...

  • Page 81: Adjustable Legrest

    9.1.2 Adjustable legrest 9.1.2.1 Adjusting the angle Prerequisites: • 1x 10 mm open-ended spanner • Use the open-ended spanner to loosen the counternut (1). • Move the legrest to the desired position by turning the spindle (2). • Tighten the counternut.

  • Page 82: Adjusting The Length Of The Legrest

    9.1.2.2 Adjusting the length of the legrest Prerequisites: • 1x 5 mm socket head spanner • Use the socket head spanner to loosen the fastening screws (1). • Slide the foot support to the desired height. • Tighten the fastening screws.

  • Page 83: Adjusting The Calf Plate To The Calf Width Of The User

    9.1.2.3 Adjusting the calf plate to the calf width of the user The calf plate of the legrest can be adapted to the user’s calf width by bending apart or together. • Bending the calf plate to the desired width.

  • Page 84: Adjusting The Angle Of The Foot Plate

    9.1.2.4 Adjusting the angle of the foot plate Prerequisites: • 1x 5 mm socket head spanner • Fold up the foot plates in order to access the adjusting screws. • Use the socket head spanner to adjust the adjusting screws (1). •...

  • Page 85: Legrests Or Footrests Attached To The Side

    Legrests or footrests attached to the side 9.2.1 Vari-F footrest 9.2.1.1 Swivelling the footrest outward and/or removing The small unlocking button is located on the upper section of the footrest. When the footrest is unlocked, it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely.

  • Page 86: Setting The Angle

    9.2.1.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! Requirements: •...
  • Page 87 • Loosen the screw (1) using the Allen key. • Set the desired angle. • Re-tighten the screw.

  • Page 88: Setting The End Stop Of The Footrest

    9.2.1.3 Setting the end stop of the footrest Pre-requisites: • 1x 6 mm Allen key • 1x 10 mm open-ended spanner The end position of the footrest is determined by means of a rubber stop (1). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 89 • Use the Allen key to loosen the screw (1) and swivel the footrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 90 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the screw.

  • Page 91: Adjusting The Length Of The Footrest

    9.2.1.4 Adjusting the length of the footrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! Pre-requisites: •...

  • Page 92: Vari-A Legrests

    9.2.2 Vari-A legrests 9.2.2.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 93: Setting The Angle

    9.2.2.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! •...
  • Page 94 • Set the required angle. • Retighten the handscrew (1) again.

  • Page 95: Setting The End Stop Of The Legrest

    9.2.2.3 Setting the end stop of the legrest Pre-requisites: • 1x 10 mm open-ended spanner The end position of the legrest is determined by means of a rubber stop (A). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 96 • Disengage the release handle (1) and swivel the legrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 97 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the release handle.

  • Page 98: Adjusting The Length Of The Legrest

    9.2.2.4 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! Pre-requisites: •...

  • Page 99: Adjusting The Depth Of The Calf Plate

    9.2.2.5 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 100: Adjusting The Height Of The Calf Plate

    9.2.2.6 Adjusting the height of the calf plate Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 101: Unlocking And Swivelling The Calf Plate Backward When Alighting

    9.2.2.7 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 102: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 9.2.2.8 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 103: Adjusting The Angle And Depth Adjustable Foot Plate

    9.2.2.9 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...

  • Page 104: Ade Legrests

    9.2.3 ADE legrests 9.2.3.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 105: Setting The Angle

    9.2.3.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! The electrically height-adjustable legrests are operated using the remote.

  • Page 106: Adjusting The Length Of The Legrest

    9.2.3.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that neither the legrests nor the steering wheels contact the ground! Pre-requisites: •...

  • Page 107: Adjusting The Depth Of The Calf Plate

    9.2.3.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 108: Adjusting The Height Of The Calf Plate

    9.2.3.5 Adjusting the height of the calf plate Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 109: Unlocking And Swivelling The Calf Plate Backward When Alighting

    9.2.3.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 110: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 9.2.3.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 111: Adjusting The Angle And Depth Adjustable Foot Plate

    9.2.3.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...

  • Page 112: Angle-Adjustable Footboard

    9.2.4 Angle-adjustable footboard Requirements: • Torx open-ended spanner T25 • Allen key 5 mm • Release the screws (1) with the Torx spanner and remove. • Adjust to required width. • Retighten the bolts. • Glue the anti-slip rubber mat to the footboard.
  • Page 113 • Loosen the locking screw(1) on both sides with the mm Allen key. • Adjust the footboard to the required angle. • Retighten the bolts.

  • Page 114: Electrical System

    NOTE A defective main fuse may be replaced only after checking the entire electric system. An Invacare® specialised dealer must perform the replacement. You can find information on the fuse type in chapter "Technical Specifications" starting on page 134.

  • Page 115: Batteries

    10.2 Batteries 10.2.1 What you need to know about batteries Power is supplied by two 12V batteries. The batteries are maintenance-free and only need regular charging. New batteries should always be fully charged once before their first use. New batteries will be at their full capacity after having run through approx.
  • Page 116 The batteries cannot be overcharged with the specified charger. Please use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements.

  • Page 117: 10.2.2 Charging The Batteries

    • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®! Danger of electric shock and damage to the battery charger if it is allowed to get wet! • Protect the battery charger from water! •...

  • Page 118: 10.2.3 How To Handle Damaged Batteries Correctly

    • Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.

  • Page 119: Maintenance

    Maintenance encompasses different areas, such as everyday care and cleaning, inspection checks, repair tasks and refurbishment. NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. 11.1...

  • Page 120: Inspection Checks

    Invacare® dealer. Please refer to the service manual for this mobility device for an extensive list of inspections and instructions for upkeep.

  • Page 121: 11.2.1 Before Each Use Of The Mobility Device

    11.2.1 Before each use of the mobility device Component Inspection If inspection is not passed Horn • Check of correct mode of operation. • Notify dealer Lighting unit • • Check of correct operating mode for all Notify dealer lights such as indicators, headlights and rear lights.

  • Page 122: 11.2.2 Weekly

    11.2.2 Weekly Component Inspection If inspection is not passed Armrests /side • • Check to ensure that the Tighten the screw or camping lever panels armrests can be correctly to fix the armrests (see chapter inserted in the holders and "Adjusting the armrests and the do not wobble.

  • Page 123: 11.2.3 Monthly

    11.2.3 Monthly Item Inspection check Action All upholstered parts • • Check for damage and wear. Contact your dealer. Removable legrests • • Check whether the legrests can be fixed Contact your dealer. securely and whether the loosening mechanism is properly operable (see chapter "Adjusting footrests and legrests"...

  • Page 124: Repair Instructions

    "Technical Specifications" on page 134, or consult the Service Manual, available from Invacare® (in this connection please see the addresses and phone numbers in section "How can you get in touch with Invacare®?" on page 2). In case you require assistance, please contact your Invacare® Dealer.

  • Page 125: Repairing A Flat Tyre (Front)

    11.3.2 Repairing a flat tyre (front) Requirements: • Allen key 5 mm • Open-end spanner 24 mm • Repair kit for inner tubes or a new inner tube. • Talcum powder Remove the wheel • Jack the vehicle up and place a block of wood underneath it to prop it up.
  • Page 126 Repair the flat tyre • Remove the valve cap. • Let the air out of the tyre completely by pressing the pin in the centre of the valve in. • Remove the 5 Allen screws (1) • Take the tyre and the inner tube off of the rim halves. •...
  • Page 127 • Place the rim halves in the tyre from the outside. • Pump up the tyre a little. • Re-position the Allen screws in the rim and tighten them firmly. Make sure the inner tube does not get pinched between the rims halves! •...

  • Page 128: Repairing Tyre Punctures (Drive Wheel)

    11.3.3 Repairing tyre punctures (drive wheel) Injury hazard! If the wheel has been insufficiently tightened during assembly, it can become loosened during driving! • When reassembling the drive wheels, tighten the Allen screws at a torque of 30 Nm! • Secure all screws using a suitable blocker (e.g. Loctite 243)! Requirements: •...
  • Page 129 NOTE Re-assembly is done in reverse order. Ensure that the tyre is replaced on the same side and in the same travel direction as it was previously mounted. Repairing the flat tyre EXPLOSION HAZARD! The wheel will explode if you do not let the air out of the tyre before removing the wheel! •...
  • Page 130 • Insert the wheel rim halves from outside into the tyre. • Pump a little air into the inner tube. • Reinsert the cylinder head screws and tighten to10 Nm. Avoid crushing the inner tube! • Ensure that the tyre outer is seated correctly. •...

  • Page 131: Transport

    Transport CAUTION! Injury hazard! The presence of a restraint system on a wheelchair under no circumstances implies that the wheelchair can be used as a vehicle seat! • This wheelchair meets the requirements of ISO 7176/19-2001 and may under no circumstances be used as a vehicle seat or for the transport of the user in a vehicle! •...

  • Page 132: Securing The Wheelchair For Transport Without Passengers

    12.2 Securing the wheelchair for transport without passengers CAUTION: Injury hazard! • If you are unable to fasten your electric wheelchair securely in a transport vehicle, we recommend that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.

  • Page 133: Refurbishment

    • Cleaning and disinfection. Please see chapter "Maintenance" on page 119. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating posture" on page 40.

  • Page 134: Technical Specifications

    Technical Specifications Permissible Operating and Storage Conditions Temperature range for operation • -25 … +50 °C according to ISO 7176-9: Temperature range for storage • -40 … +65 °C according to ISO 7176-9: Electrical system Motors • 300 W (6 km/h) •...
  • Page 135 Driving characteristics Speed • 6 / 10 km/h Max. safe slope • 10.5 % (6°) Stat. / 14% (8°) Dyn. Max. climable • 10 cm obstacle height (with kerb climber) Max. climable • 6 cm obstacle height (without kerb climber) Turning radius •...
  • Page 136 *** Measured without seat cushion **** The actual kerb weight depends on the fittings your mobility aid has been supplied with. Every Invacare® mobility aid is weighed when leaving the works. Please refer to the nameplate for the kerb weight (including batteries) measured.

  • Page 137: Inspections Performed

    It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...

Table of Contents