Advertisement
Advertisement
Table of Contents
Related Manuals for DigiTech HardWire series
Summary of Contents for DigiTech HardWire series
- Page 1 Supernatural A M B I E N T V E R B...
-
Page 2: Declaration Of Conformity
Sandy, Utah 84070, USA of EN60065, EN60742, or Date: June 25, 2012 equivalent.) European Contact: Your local DigiTech Sales and Service conforms to the following Product Specifications: Office or Safety: IEC 60065 -01+Amd 1 Harman Signal Processing... - Page 3 WARNING If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. For your protection, read the following: Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you Important Safety Instructions...
- Page 4 7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
- Page 5 If you notice a change in the LED’s brightness, or the pedal will not switch from Bypass to Effect, replace the battery with a new 9-Volt alkaline battery or visit your local DigiTech dealer to obtain the optional power adapter and unleash the pedal’s full potential with unlimited power.
-
Page 7: Included Items
Introduction More than a remarkable achievement, DigiTech’s HardWire series represents ® a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers, providing such... - Page 8 Pedal Interface M I X L I V E L I N E S S D E C AY Supernatural A M B I E N T V E R B...
- Page 9 What Does This Do? 1. Mix Knob - Controls the reverb level. Turn this knob clockwise to increase and counter-clockwise to decrease the reverb level. 2. DC Adapter Jack - Connect the optional power supply to this jack. Use the proper supply for your area’s mains line voltage. 3.
- Page 10 supernova • - Deep space reverb with twisting flange and pitch shifting. shine • - Shimmer reverb with a thick lush chorus added. pherb • - Rich Lexicon Hall reverb with a hint of phasing. spring • - The unmistakable classic ‘surf ’ reverb. 6.
- Page 11 8. Foot Switch Release Pins - These two pins are spring loaded hinges that hold the Foot Switch in place. See page 10 for information on accessing and changing the battery. See page 6 for more information about using and changing the Tails Switch settings. 9.
- Page 12 Tails Switch The Supernatural features a switch that allows the reverb signal to continue being heard after the effect is bypassed. When the Tails Switch is set ON, the Supernatural does not utilize true hardwire bypass. If you always want to use true hardwire bypass, set the Tails Switch to OFF.
-
Page 14: Amplifier Setup
Amplifier Setup Optional Power Supply M I X L I V E L I N E S S D E C AY Supernatural A M B I E N T V E R B... - Page 15 Effects Setup AMP RETURN Optional Power Supply AMP SEND M I X L I V E L I N E S S D E C AY Supernatural A M B I E N T V E R B Note: If the amp effects loop has a mix control, set the mix to 100% full wet.
-
Page 16: Battery Operation
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1. - Page 17 into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both release pins are flush with the outer side of Foot Switch the pedal. Pedal Switch 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin...
- Page 18 Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • Foot Switch Glow Sticker (easily visible on dark stages) •...
- Page 19 Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal.
- Page 20 Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
- Page 21 StompLock To place the StompLock over the pedal knobs, do the following: 1. Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. 3. To remove the StompLock, gently lift one side and then the other.
-
Page 22: Specifications
Specifications Controls: Level, Liveliness, Decay, Type, On/Off Pedal Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance: >1 MΩ (stereo), >500 kΩ (mono) - effect on Output Impedance: 1 kΩ - effect on Input Impedance: True hardwire bypass - effect off Output Impedance: True hardwire bypass - effect off Power Supply:... - Page 24 8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 DigiTech and HardWire ® ® registered trademarks of Harman Designed in the USA Copyright - Harman Printed in China HardWire Supernatural ® Owners Manual 5020843-B Please visit our website at: www.digitech.com...