1. Manuals
  2. Brands
  3. Kyocera Mita Manuals
  4. Printer
  5. Ecosys FS-1000+
  6. Installation manual

Kyocera Mita FS-1000+ Installation Manual

Page printer
Hide thumbs Also See for FS-1000+:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Page Printer
Installation Manual

Advertisement

Table of Contents
loading

Related Manuals for Kyocera Mita FS-1000+

Summary of Contents for Kyocera Mita FS-1000+

  • Page 1 Page Printer Installation Manual...

  • Page 2: Table Of Contents

    MODE. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures described in the User's Manual contained as an electronic file in the Kyocera Mita Digital Library CD-ROM supplied with the printer. Notice The information in this manual is subject to change without notification.

  • Page 3: Step1 Unpacking

    Toner Container (TK-17) Power Cord Cleaning Cloth Installation Manual (this booklet) Kyocera Mita Digital Library CD-ROM Removing Shipping Material Remove the tape on the rear side of the printer, and remove the two spacers and printed notice from the paper cassette.

  • Page 4: Step2 Positioning The Printer

    Ifs10ep-jp.book Page 2 Friday, December 22, 2000 4:27 PM STEP Positioning the Printer Make sure that the place of installation meets the following requirements: Clearance Be sure to secure enough space 30 cm (11-13/16 inches) around the printer. Prolonged use without sufficient clearance 40 cm (15-3/4 may cause heat to build up...

  • Page 5: Step3 Installing The Toner Container

    Ifs10ep-jp.book Page 3 Friday, December 22, 2000 4:27 PM STEP Installing the Toner Container Before you can use the printer for the first time, you must set up the printer by installing the toner container and interfacing with the computer. Open the printer top cover all the way.
  • Page 6 Ifs10ep-jp.book Page 4 Friday, December 22, 2000 4:27 PM Carefully remove the protective seal. Install the toner container into the printer. Push firmly on the top of the toner con- tainer at the positions marked PUSH HERE.
  • Page 7 Ifs10ep-jp.book Page 5 Friday, December 22, 2000 4:27 PM Push the lock lever to the lock (LOCK) position. Close the top cover. When the printer is first switched on after toner installa- tion, there will be a delay of approximately 15 minutes before the printer gets ready to print.

  • Page 8: Step4 Connecting The Printer To The Computer

    Ifs10ep-jp.book Page 6 Friday, December 22, 2000 4:27 PM STEP Connecting the Printer to the Computer There are various ways of connecting the printer to the computer, such as through the parallel interface connector or through the optional network interface board. Printer Connections Network Optional Serial Interface...

  • Page 9: Parallel Interface Connection

    Ifs10ep-jp.book Page 7 Friday, December 22, 2000 4:27 PM Parallel Interface Connection Plug one end of the printer cable (not included) into the parallel interface con- nector on the rear of the printer. Clips • Use a parallel printer cable that complies with the IEEE1284 standards.

  • Page 10: Step5 Connecting The Power Cord

    Ifs10ep-jp.book Page 8 Friday, December 22, 2000 4:27 PM STEP STEP Connecting the Power Cord This section describes the procedure for connecting the power cable and various cautions. Notes on Power Supply • Install the printer near an AC wall outlet, preferably one that can be used for the printer alone.

  • Page 11: Step6 Adding Paper To The Paper Cassette And Mp Tray

    Ifs10ep-jp.book Page 9 Friday, December 22, 2000 4:27 PM STEP Adding Paper to the Paper Cassette and MP Tray The paper cassette can accommodate A5 to Legal size paper and can hold approxi- mately 250 sheets. The Multi-Purpose tray can accommodate the various paper sizes and can hold approximately 50 sheets of paper.
  • Page 12 Ifs10ep-jp.book Page 10 Friday, December 22, 2000 4:27 PM Pull the paper cassette all the way out of the printer. Adjust the position of the paper stopper located at the rear of the paper cassette. Release Button Press in the release button and slide the Paper Stopper stopper to the desired paper size.
  • Page 13 Ifs10ep-jp.book Page 11 Friday, December 22, 2000 4:27 PM Make sure that the edges of the paper are aligned. Slide the paper into the paper cassette. Do not load more paper than will Load Limit fit under the load limits on the top of the paper guides.
  • Page 14 Ifs10ep-jp.book Page 12 Friday, December 22, 2000 4:27 PM Multi-Purpose (MP) tray Pull the MP tray towards you until it stops. Pull out the subtray and unfold the flap. Subtray Flap Adjust the position of the paper guides on the MP tray. Standard paper sizes are attached to the MP tray.
  • Page 15 Ifs10ep-jp.book Page 13 Friday, December 22, 2000 4:27 PM Envelopes Envelopes should be fed in the face-up position, right edge first. • Test a sample envelope on the printer and check that printing quality is satisfactory before purchasing. • To avoid trouble, we recommend that envelopes be delivered face-up using the face-up tray.

  • Page 16: Step7 Using The Face-Up Output Tray

    Ifs10ep-jp.book Page 14 Friday, December 22, 2000 4:27 PM STEP Using the Face-Up Output Tray Use the face-up output tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, trans- parencies, or thick paper.

  • Page 17: Step8 Printing A Status Page

    Ifs10ep-jp.book Page 15 Friday, December 22, 2000 4:27 PM STEP Printing a Status Page To test the printer, print a status page indicating factory settings. Turn on the printer’s power switch. Upon turning on the power, the printer’s 4 indicators flash in sequence until printer initialization is complete, then the indicator ( [on line]) lights...

  • Page 18: Correcting A Paper Jam

    Ifs10ep-jp.book Page 16 Friday, December 22, 2000 4:27 PM Correcting a Paper Jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover once.
  • Page 19 Ifs10ep-jp.book Page 17 Friday, December 22, 2000 4:27 PM Open the printer's front cover. Front Cover Lift the process unit together with the toner container out of the printer. Process Unit Remove the jammed paper. When pulling the paper, pull gently so as not to tear it.

  • Page 20: Laser Safety

    I Caution to user Any modification without prior permission may cause harmful interference. If any modification/change is introduced to this equipment without prior permission, Kyocera Mita as the manufacturer cannot guarantee compliance with FCC rules. To use equipment which does not comply with FCC rules is prohibited.
  • Page 21 Ifs10ep-jp.book Page 19 Friday, December 22, 2000 4:27 PM DANGER: INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Caution labels Label inside the printer (Laser radiation warning) (European/Asian/Pacific countries)
  • Page 22 Ifs10ep-jp.book Page 20 Friday, December 22, 2000 4:27 PM IMPORTANT SAFEGUARDS 1. Read all of these instructions and save these instructions for later use. 2. Unplug this product from the wall outlet before cleaning. 3. Do not use this product near water. 4.
  • Page 23 User's instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information Kyocera Mita Australia Pty., Ltd. Go to next page...

  • Page 24: Moving The Printer

    Model Number: Laser Printer FS-1000+ (as tested with enhancement optional units: PF-17, IB-10E.) Trade Name: Kyocera Responsible Party: Kyocera Mita America Inc. Address: 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-0008, U.S.A. Telephone number: (973) 808-8444 Fax number:...
  • Page 25 Ifs10ep-jp.book Page 23 Friday, December 22, 2000 4:27 PM ® NERGY As an E Partner, Kyocera Mita Corporation has determined NERGY that this product meets the E guidelines for energy effi- NERGY ciency. The basic objective of the E Program is to reduce environ-...
  • Page 26 PK-6 KPDL2 Upgrade Kit IB-10E Serial Interface Board Kit Network Boards See your Kyocera Mita dealer for purchasing information of the network board that is best suited for use with this printer. Use only the network board operating from DC 3.3V.
  • Page 27 Adobe Systems Incorporated. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. is a U.S. registered mark. NERGY This Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A.
  • Page 28 Ifs10ep-jp.book Page 26 Friday, December 22, 2000 4:27 PM 3. Limitation of Remedies IBM's entire liability under this license is the following; 1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM's liability will be for actual damages only and will be limited to the greater of: a) the equivalent of U.S.$25,000 in your local currency;...
  • Page 29 Ifs10ep.book Page 26 Tuesday, December 19, 2000 9:09 PM This page intentionally left blank.
  • Page 30 Ifs10ep.book Page 26 Tuesday, December 19, 2000 9:09 PM This page intentionally left blank.
  • Page 31 Ifs10ep-jp.book Page 27 Friday, December 22, 2000 4:27 PM Operating Keys and Indicators For details on operating procedures, see the FS-1000+ User's Manual contained as an elec- tronic file in the CD-ROM supplied with the printer. Number Name Function On line indicator Indicates whether the printer is on-line or off-line.

Table of Contents