Schedules; How The Event Action Is Taken - Panasonic WJ-ND400K Installation Manual

Network disk recorder
Hide thumbs Also See for WJ-ND400K:
Table of Contents

Advertisement

● Schedules
It is possible to create a timetable by dividing a day into up to 6
time zones and to create schedules by assigning programs to
the created time zones. Up to 8 programs can be created, and
the settings relating to the recording for each program such as
the recording rate and the recording duration of the event
recording can be configured.
● How the event action is taken
About events
In the recorder, an "event" is defined as a phenomenon which
triggers a specific action (event action) in the recorder.
The recorder regards the reception of a terminal alarm, a com-
mand alarm, and a site alarm as an "event".
For example, when the recorder receives a site alarm issued by
a camera, the recorder regards it as an event occurrence.
About the event action
When an event occurs, the recorder will take a specified event
action.
The following actions will be taken as the event actions
according to the settings.
• Record images/audio
• Record logs
• Notify of an event occurrence (by mail, LED, buzzer, image
transmission to a FTP server, etc.)
Events
(Terminal alarms, site alarms,
and command alarms)
Event action
-Event recording
-Log
Alarm action
-Mail notification
-LED
-Buzzer
-FTP transmission
Image of event/alarm action
The recorder will take an event action when the following
events occur.
Terminal alarm: When a signal from an external alarm device
such as a door sensor is supplied to the alarm input termi-
nal (ALARM connector or ALARM/CONTROL connector at
the rear of the recorder), it will be regarded as a terminal
alarm.
Command alarm: When receiving a command from a PC via a
network, it will be regarded as a command alarm.
Site alarm: When receiving a Panasonic alarm protocol from a
network camera, it will be regarded as a site alarm.
The following are the event actions and their descriptions.
• Start recording
Recording will start according to the settings configured on
the setup menu such as the recording rate, the recording
duration, etc. Images recorded before an event occurrence
can be associated with images recorded by the corre-
sponding event recording so that images recorded at the
event occurrence can be played as if the recording started
before the event occurrence. (Pre-event recording)
• Display the event notification window
A pop-up window that notifies of an event occurrence will
be displayed.
• Blink the alarm indicator
The alarm indicator on the front panel will start blinking.
• Sound the buzzer
The buzzer will start sounding for the duration set in
advance.
• Move the registered camera to the preset position
The camera registered in advance will move to the preset
position according to the settings.
• Send a mail that notifies of an event occurrence
A mail that notifies of the event occurrence with the time
and date of the event occurrence will be sent. (Alarm mail)
It is possible to attach an image to the alarm mail. (Alarm
image)
Up to 4 destination addresses for the alarm mail can be
registered.
• Output signals from the ALARM/CONTROL connector at
the rear of the recorder. (Alarm output)
When an event occurs, a signal will be output from the
ALARM/CONTROL connector at the rear of the recorder to
sound an external alarm buzzer, etc.
• Save a log
A log that contains the event type and the time and date of
the event occurrence will be saved. (Event log)
• Send recorded images to an FTP server at an event occur-
rence
When an event occurs, recorded images will continue
transmitting to an FTP server automatically for the set
duration from the time when the event occurred.
• Notify a PC of an event or an error occurrence using the
Panasonic alarm protocol
When an event or an error occurs, information about the
event/ error will automatically be notified to the registered
PC according to the "Panasonic alarm protocol" setting. To
receive a notification and display the contents of it, it is
necessary to install the optional dedicated software.
Refer to the "readme.txt" on the provided CD-ROM about
the dedicated software.
19

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wj-nd400k/g

Table of Contents