Initialization Of Data; Initializing All Pages Data; F Page Adjustment Address - Sony DSC-F828 Service Manual

DSC-F828
1-2.

INITIALIZATION OF DATA

1-2-1. INITIALIZATION OF DATA

1. Initializing All Pages Data

By performing the following procedure, data of all the pages will
be initialized.
Initializing Method:
1) Select page: 00, address: 01, and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is "03".
4) Click [All] of the ALL SELECT buttons to select all pages.
(Fig. 6-1-8. A)
5) Click [Write] to write the initializing data to the EEPROM of
the camera.
6) Wait for 2 sec.
7) Click [Close] to close the SEUS PAGE EDIT screen.
Modification of 4F, 8E Page Data
If all page data have been initialized, change the data of the "Fixed
data-2" address shown in the following tables by manual input.
1) Select page: 00, address: 01, and set data: 01.
2) Click [Page] on the SEUS screen, and input "4F" or "8E".
3) Click [Address], and input the "Fixed data-2" address.
4) Click [Set], and input the new data.
Note: New data for changing are not shown in the table because they
are different in destination. When changing the data, copy the
data built in the same model. If copy the data built in the different
model, the camera may not operate.
5) Repeat steps 2 to 4 until all data of the "Fixed data-2" addresses
are changed.
6) Click [Save] to write the changed data to the EEPROM of the
camera.
7) Wait for 2 sec.
Processing after Completing Initializing of data
Order Page Address Data
1 20 00
2 20 01
3
4
5
Procedure
29 Set the data.
29 Set the data.
Check "Receive Paket Error" is
displayed on the SEUS screen.
Turn on the power of the camera.
Click [Connect] on the SEUS
screen.
2. Initializing Single Page Data
By performing the following procedure, data of the page that you
want to initialize will be initialized.
Initializing Method:
1) Select page: 00, address: 01, and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is "03".
4) Click [All] of the option buttons of the target page. (Fig. 6-1-8. B)
5) Click [Write] to write the initializing data to the EEPROM of
the camera.
6) Wait for 2 sec.
7) Click [Close] to close the SEUS PAGE EDIT screen.
Note: When 4F page or 8E page is initialized, perform "Modification of
4F, 8E Page Data". (Refer to "1. Initializing All Pages Data".)
Processing after Completing Initializing of data
Order Page Address Data
1 20 00
2 20 01
3
4
5
B
A

3. 2F Page Adjustment Address

Address Address
Initial value Initial value
23 80
4. 4F Page Adjustment Address
Address Address
Initial value Initial value
46
47
88
94 00
95 00
96 00
97 00
A1
6-8
Procedure
29 Set the data.
29 Set the data.
Check "Receive Paket Error" is
displayed on the SEUS screen.
Turn on the power of the camera.
Click [Connect] on the SEUS
screen.
Fig. 6-1-8.
Remark Remark
Test mode
Table. 6-1-2.
Remark Remark
Fixed data-2
Fixed data-2
Fixed data-2
Recording counter
(Refer to "Record of Use check"
of "SERVICE MODE"(Page 6-42).)
Fixed data-2
Table. 6-1-3.