Cisco ASR 9000 Series Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Wireless Router
  5. ASR 9000 Series
  6. Installation manual
Cisco ASR 9000 Series Installation Manual

Cisco ASR 9000 Series Installation Manual

Aggregation services router ethernet line card
Hide thumbs Also See for ASR 9000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual, Installation Manual
Cisco ASR 9000 Series
Aggregation Services Router
Ethernet Line Card Installation Guide
January 2015
Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR 9000 Series

Summary of Contents for Cisco ASR 9000 Series

  • Page 1 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide January 2015 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
  • Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.

  • Page 3: Table Of Contents

    1-31 2-Port 10-Gigabit Ethernet Modular Port Adapter with XFP 1-33 4-Port 10-Gigabit Ethernet Modular Port Adapter with XFP 1-34 8-Port 10-Gigabit Ethernet Modular Port Adapter with SFP+ 1-36 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 4 Using show Commands to Verify Modular Line Card and Modular Port Adapter Status 2-23 Using show Commands to Display Modular Port Adapter Information 2-24 Using the ping Command to Verify Network Connectivity 2-26 Installing and Removing SFP Modules 2-28 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 5 2-59 Overview 2-59 CPAK Module Specifications 2-59 CPAK Module Cabling Specifications 2-60 CPAK Module Optical Transmit and Receive Specifications 2-60 MPO-24 Connector Pin Specifications 2-60 Required Tools 2-61 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 6 Configuring and Troubleshooting Line Card Interface Cards Configuration Parameters Line Card Interface Address Using Configuration Commands Basic Line Card Configuration Verifying the Transceiver Modules Advanced Line Card Troubleshooting Regulatory, Compliance, and Safety Information 3-10 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 7 Cisco 10-Gigabit Ethernet CWDM SFP+ Transceiver Modules A-14 Cisco 10-Gigabit Ethernet XFP Modules A-14 Cisco DWDM XFP Transceiver Modules A-15 Ethernet Line Card Power Consumption Values A-17 Ethernet Line Card Physical Dimensions A-19 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 8 Contents Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide viii...

  • Page 9: Changes To This Document

    September 2012 Information added about the new 1-port 40GE Modular Port Adapter (MPA), the new 36-Port 10-Gigabit Ethernet Line Card and the new 1-Port 100-Gigabit Ethernet Line Card, plus updates to the transceiver module information. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 10: Document Organization

    Initial release of this document. Audience This guide is written for hardware installers and system administrators of Cisco routers. This publication assumes that the user has a substantial background in installing and configuring router and switch-based hardware. The reader should also be familiar with electronic circuitry and wiring practices, and have experience as an electronic or electromechanical technician.

  • Page 11: Document Conventions

    Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 12 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide -xii...

  • Page 13: Cisco Asr 9000 Series Line Card Product Overview

    C H A P T E R Overview Cisco ASR 9000 Series Line Card Product This chapter provides an overview of the Cisco ASR 9000 Series line cards and includes these sections: Cisco ASR 9000 Series Ethernet Line Cards, page 1-1 •...
  • Page 14 3. SFP = Gigabit Ethernet small form-factor pluggable transceiver module 4. SFP+ = 10-Gigabit Ethernet small form-factor pluggable transceiver module 5. QSFP+ = 40-Gigabit Ethernet Quad Small Form-factor Pluggable plus transceiver module Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 15 Cisco IOS XR Software Release and Hardware Revision Requirements The Cisco ASR 9000 line cards have specific Cisco IOS XR software requirements. To ensure compatibility with the software, each line card has a specific hardware revision number. The number is printed on a label affixed to the component side of the card and is displayed by the show diag command.Table 1-2...
  • Page 16 Cisco IOS XR release. If the command displays indicate that the Cisco IOS XR software is a version earlier than you need, check the contents of flash memory to determine if the required images are available on your system.

  • Page 17: Ethernet Line Card Comparison

    Cisco ASR 9000 Series Line Card Product Overview Ethernet Line Card Comparison Ethernet Line Card Comparison Most of the Cisco ASR 9000 line cards are available in base, extended, and low-queue versions. All versions are functionally equivalent, but vary in configuration scale and buffer capacity. Table 1-3 provides comparative information about the various line cards.
  • Page 18 Cisco IOS XR software to identify and validate the module as qualified to operate with Ethernet line cards. Unapproved modules (those not purchased directly from Cisco) will work, but generate an error message stating that the device is unsupported.

  • Page 19: Port 10-Gigabit + 20-Port Gigabit Ethernet Combination Line Card With Xfp

    LED visible on the front panel. The Link LED indicates the status of the associated XFP or SFP port, as described in Status LEDs, page 3-2. Figure 1-1 shows the line card front panel and LEDs. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 20 10 Captive installation screw (one of two) Note The interface numbering starts with zero for the GE and 10GE ports, so this line card has ports identified as Te0/x/0/0 and a Gig0/x/0/0. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 21: Port 10-Gigabit Ethernet 2:1 Oversubscribed Line Card With Xfp

    LEDs. Table A-14 for a list of all XFPs supported on the 8-Port 10GE 2:1 oversubscribed line card and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 22 Ejector lever (one of two) Port 7 XFP cage Port 0 XFP cage Status LED Port status LED (one per port) Captive installation screw (one of two) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-10...

  • Page 23: Port 10-Gigabit Ethernet Line Card With Xfp

    Link LED indicates the status of the associated XFP port, as described in Status LEDs, page 3-2. Figure 1-3 shows the line card front panel and LEDs. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-11...
  • Page 24 Ejector lever (one of two) Port 3 XFP cage Port 0 XFP cage Status LED Port status LED (one per port) Captive installation screw (one of two) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-12...

  • Page 25: Port 10-Gigabit Ethernet 80 Gbps Line Rate Card With Xfp

    Table A-14 for a list of all XFPs supported on the 8-Port 10GE 80 Gbps line rate card and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-13...
  • Page 26 Ejector lever (one of two) Port 7 XFP cage Port status LED (one per port) Line card status LED Port 0 XFP cage Captive installation screw (one of two) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-14...
  • Page 27 Aggregation Services Router System Management Configuration Guide, Release 5.3.x. The license product number for the A9K-4T16GE-TR card is A9K-2T-TR-LIC. The license product number for the A9K-4T16GE-SE card is A9K-2T-SE-LIC. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-15...
  • Page 28 1GE port 15 SFP cage 1GE port 14 SFP cage 1GE port 1 SFP cage 10 Captive installation screw (one of two) 10GE port 1 SFP+ cage SFP+ Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-16...
  • Page 29 Link LED indicates the status of the associated SFP+ port, as described in Status LEDs, page 3-2. Figure 1-6 shows the line card front panel and connectors. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-17...
  • Page 30 Captive installation screw (one of two) Table A-3 for a list of all SFP+ transceiver modules supported on the 16-Port 10GE oversubscribed line card and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-18...
  • Page 31 Link LED indicates the status of the associated SFP+ port, as described in Status LEDs, page 3-2. Figure 1-7 shows the line card front panel and connectors. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-19...
  • Page 32 Captive installation screw (one of two) Table A-3 for a list of all SFP+ transceiver modules supported on the 16-Port 10GE oversubscribed line card and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-20...
  • Page 33 Each SFP+ cage on the 24-Port 10GE line card has an adjacent Link LED visible on the front panel. The Link LED indicates the status of the associated SFP+ port, as described in Status LEDs, page 3-2. Figure 1-8 shows the front panel and connectors. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-21...
  • Page 34 Line card status LED Port 11 SFP+ cage Table A-3 for a list of all SFP+ transceiver modules supported on the 24-Port 10GE line card and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-22...
  • Page 35 The 36-Port 10-Gigabit Ethernet (GE) line card has thirty-six10-Gigabit SFP+ (10GE SFP) module ports. Figure 1-9 shows the line card front panel connectors and indicators. Figure 1-9 36-Port 10-Gigabit Ethernet Line Card Front Panel Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-23...

  • Page 36: Port Gigabit Ethernet Line Card With Sfp

    Link LED indicates the status of the associated SFP port, as described in Status LEDs, page 3-2. Figure 1-10 shows the line card front panel and connectors Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-24...
  • Page 37 Port 38 SFP cage Captive installation screw (one of two) Table A-2 for a list of all SFP modules supported on the 40x1GE line card, and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-25...
  • Page 38 100 GE long-reach over 4 WDM lanes (LR4) 10 km optics (single-mode fiber) CFP-100G-SR10 100 GE over 10 short-reach optical lanes 100 m (SR10) optics (multimode fiber) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-26...
  • Page 39 Figure 1-11 1-Port 100-Gigabit Ethernet Line Card Front Panel Ejector lever (one of two) 100 Gigabit Ethernet CFP Captive installation screw (one of two) Line card status LED Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-27...
  • Page 40 LEDs. Table 1-4 for the list the optics and connectors used by the two 100 GE ports on the 2-port 100 GE line card. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-28...
  • Page 41 Ejector lever (one of two) 100-Gigabit Ethernet CFP connector (two of two) Captive installation screw (one of two) Line card status LED 100-GE CFP connector (one of two) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-29...

  • Page 42: Port 100-Gigabit Ethernet Line Card With Cpak

    Status LEDs, page 3-2. Figure 1-13 shows the line card front panel and connector. The Cisco 8-Port 100-Gigabit Ethernet (GE) line card supports the CPAK modules listed in Table A-4. Figure 1-13 8-Port 100-Gigabit Ethernet Line Card Ejector lever (one of two)

  • Page 43: Modular Line Cards And Modular Port Adapters

    Figure 1-15 shows the MPA and corresponding LEDs Table A-2 for a list of all SFP modules supported on the 20x1GE modular port adapter, and their operating parameters. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-31...
  • Page 44 Modular port adapter power is off. Green Modular port adapter is ready and operational. Amber Modular port adapter power is on and good, and modular port adapter is being configured. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-32...

  • Page 45: 2-Port 10-Gigabit Ethernet Modular Port Adapter With Xfp

    Meaning Port is not enabled. Green Port is enabled and the link is up. The MPA A/L (Active/Link) LED will blink green when there is traffic activity. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-33...

  • Page 46: 4-Port 10-Gigabit Ethernet Modular Port Adapter With Xfp

    The MPA has two types of LEDs: an A/L (Active/Link) LED for each individual port and a Status LED for the MPA as shown in Figure 1-17. The A/L LED indicates the status of the associated XFP port, as described in Table 1-7. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-34...
  • Page 47 Chapter 1 Cisco ASR 9000 Series Line Card Product Overview Modular Line Cards and Modular Port Adapters Figure 1-17 4-Port 10-Gigabit Ethernet Modular Port Adapter Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-35...

  • Page 48: 8-Port 10-Gigabit Ethernet Modular Port Adapter With Sfp

    Each SFP+ cage on the 8-Port 10GE MPA has an adjacent A/L (Active/Link) LED visible on the front panel of the card (Figure 1-18). The A/L (Active/Link) LED indicates the status of the associated SFP+ port, as described in Table 1-8. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-36...
  • Page 49 Port is enabled and the link is down. STATUS MPA power is off. Green MPA is ready and operational. Amber The MPA power is on and working is being configured. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-37...

  • Page 50: 1-Port 40-Gigabit Ethernet Modular Port Adapter With Qsfp

    The A/L LED indicates the status of the associated QSFP port, as described in Table 1-9 and a Status LED as shown in Figure 1-19. Figure 1-19 1-Port 40 Gigabit Ethernet Modular Port Adapter A/L (Active/Link) LED Status LED Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-38...

  • Page 51: 2-Port 40-Gigabit Ethernet Modular Port Adapter With Qsfp

    Each QSFP cage on the MPA has an adjacent A/L (Active/Link) LED visible on the front panel. The A/L LED indicates the status of the associated QSFP port as described in Table 1-10, and a Status LED for the MPA as shown in Figure 1-21. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-39...
  • Page 52 Cisco ASR 9000 Series Line Card Product Overview Modular Line Cards and Modular Port Adapters Figure 1-20 2-Port 40-Gigabit Ethernet Modular Port Adapter A/L (Active/Link) LED Status LED Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-40...
  • Page 53 Modular port adapter power is off. Green Modular port adapter is ready and operational. Amber Modular port adapter power is on and good, and the modular port adapter is being configured. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-41...
  • Page 54 Chapter 1 Cisco ASR 9000 Series Line Card Product Overview Modular Line Cards and Modular Port Adapters Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 1-42...
  • Page 55 • Cables and Connectors, page 2-68 • For hardware installation and configuration information for the Cisco ASR 9000 Series Router, see the Cisco ASR 9000 Series Aggregation Services Router Hardware Installation Guide. The guide includes information on how to install, maintain, and replace router subsystems, such as cooling fans, power supplies, chassis backplanes, and so on.

  • Page 56: C H A P T E R 2 Installing Line Cards In The Cisco Asr 9000 Series Router

    Electromagnetic interference (EMI) shielding is an integral component of the line card and the modular port adapter. Cisco Systems, Inc. recommends using an ESD-preventive strap whenever you are handling network equipment or one of its components.

  • Page 57: Required Tools And Equipment

    Any SFP/XFP modules you need to install (and are not already installed) • If you need additional equipment, see Cisco.com or your service representative for ordering information. Note Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 58: Removing And Installing A Line Card

    A card with an OIR count that exceeds 175 will generate a minor alarm against that slot. If the card OIR count exceeds 200, a major alarm is generated against that slot. Fan tray insertion counts are not checked against a threshold. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 59 Installing Line Cards in the Cisco ASR 9000 Series Router Removing and Installing a Line Card See the Release Notes for Cisco ASR 9000 Series Aggregation Services Routers for Cisco IOS XR Software for information about CLI commands for obtaining and resetting card insertion data. The CLI command indicates whether the particular chassis has the version of BPID that supports the counting of the OIR.

  • Page 60: Removing A Line Card

    Removing a Line Card—Cisco ASR 9010 Router Shown Loosen the captive screws Pivot the ejector levers to Slide the card out of the unseat the card from the chassis backplane connector Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 61 Place the removed line card on an antistatic mat, or immediately place it in an antistatic bag if you plan Step 8 to return it to the factory. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 62: Installing A Line Card

    Caution To prevent ESD damage, handle line cards only by the metal card carrier. Do not touch any of the electrical components or circuitry. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 63 Note On the Cisco ASR 9922 Router, the line cards in the lower half of the chassis (slots 10–19) are inserted upside down. Simultaneously pivot both ejector levers toward each other until they are parallel to the line card front Step 5 panel.

  • Page 64: Steps For Oir Line Card Removal And Insertion

    Steps for OIR Line Card Removal and Insertion Online insertion and removal (OIR) is supported, enabling you to install a card while the line card is operating. Follow these steps when removing or inserting a line card by using the Cisco IOS XR shutdown command.

  • Page 65: Installing Modular Line Cards And Modular Port Adapters

    Do not wear loose clothing, jewelry, or other items that could get caught in the router while working with line cards. • Cisco equipment operates safely when it is used in accordance with its specifications and product usage instructions. Electrical Equipment Guidelines...

  • Page 66: Laser/Led Safety

    Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments. Statement 1051 Class 1 LED product. Statement 1027 Warning Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-12...

  • Page 67: Preventing Electrostatic Discharge

    Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI) shielding is an integral component of the line card. Cisco recommends using an ESD-preventive strap whenever you are handling network equipment or one of its components.

  • Page 68: Removing And Installing A Modular Line Card

    Some of the procedures in the following sections use illustrations of a 10-slot Note Cisco ASR 9000 Series Router to support the descriptions of removing and installing modular line cards. Although the card cages of Cisco ASR 9000 Aggregation Services Routers differ, the designated use of slots and the process of installing and removing a MLC are basically the same.

  • Page 69: Guidelines For Modular Line Card Removal And Installation

    Detach the cable-management bracket from the MLC. Use a screwdriver to loosen the captive screw at each end of the MLC faceplate. (See callout 1 on Figure 2-6). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-15...
  • Page 70 Place the removed MLC on an antistatic mat, or immediately place it in an antistatic bag if you plan to Step 7 return it to the factory. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-16...

  • Page 71: Installing A Modular Line Card

    If they do not catch, try reinserting the MLC until the ejector lever hooks are fully latched (Figure 2-7). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-17...
  • Page 72 If you are replacing a MLC install the modular port adapters (MPAs) in the same bays as you noted in Step 2 under Removing a Line Card, page 2-6. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-18...

  • Page 73: Installing And Removing Modular Port Adapters

    If you plan to install a MPA in a bay that is not in use, you must first remove the blank. Figure 2-8 Handling a Modular Port Adapter 1 Metal Carrier Printed Circuit Board 3 Grounding Strap Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-19...

  • Page 74: Online Insertion And Removal

    Hard OIR is the physical online insertion and removal of Modular port adapters (MPAs) without software commands. There are three types of hard OIR supported: If the bay is empty when the Cisco ASR 9000 Series Router MLC boots, you can do the following: Insert a 20GE MPA –...

  • Page 75: Modular Port Adapter Installation And Removal

    Inspection, cleaning, and reinspection are critical steps to take before making fiber-optic connections. Cleaning Optical Devices See the Inspection and Cleaning Procedures for Fiber Optic Connections document for information on cleaning optical devices. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-21...

  • Page 76: Checking The Installation

    Modular port adapters (MPAs) will follow the same sequence after the MLC has completed its • initialization. The MPA STATUS LEDs will illuminate amber, turning to green when the modular port adapters (MPAs) become active. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-22...

  • Page 77: Using Show Commands To Verify Modular Line Card And Modular Port Adapter Status

    Step 5 Finally, you can use the show version command to obtain software version information for the installed modular line cards (MLCs) as well as interfaces available. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-23...

  • Page 78: Using Show Commands To Display Modular Port Adapter Information

    The following sample display shows the events logged by the system as you insert a new MLC in module slot 4. RP/0/RSP0/CPU0:Dec 21 21:55:50.318 : invmgr[246]: %PLATFORM-INV-6-OIRIN : OIR: Node 0/4/CPU0 inserted RP/0/RSP0/CPU0:Dec 21 21:59:12.979 : shelfmgr[371]: %PLATFORM-SHELFMGR-6-NODE_STATE_CHANGE : 0/4/0 A9K-MPA-4X10GE state:INITIALIZED Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-24...
  • Page 79 Verify that the MPA is supported on the MLC and that it has the required hardware revision. If the MPA is not supported or has an old hardware revision, the show diag command indicates that the MLC is deactivated. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-25...

  • Page 80: Using The Ping Command To Verify Network Connectivity

    Series Aggregation Services Router Interface and Hardware Component Configuration Guide for more information on bringing up and configuring the Cisco ASR 9000 Series Router, the Cisco ASR 9000 A9K-MOD160G, and the Cisco ASR 9000 A9K-MOD80G-H. For more information on command...
  • Page 81 If the connection fails, verify that you have the correct IP address for the destination device and that the destination device is active (powered on), and then repeat the ping command. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-27...

  • Page 82: Installing And Removing Sfp Modules

    Mylar Tab SFP or SFP+ Module, page 2-32 • Actuator Button SFP or SFP+ Module, page 2-34 • Slide Tab SFP or SFP+ Module, page 2-36 • Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-28...

  • Page 83: Bale Clasp Sfp Or Sfp+ Module

    Line up the SFP module with the port and slide it into the port (Figure 2-11). Step 3 Figure 2-11 Installing a Bale Clasp SFP Module into a Port Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-29...

  • Page 84: Removing A Bale Clasp Sfp Or Sfp+ Module

    Grasp the SFP module between your thumb and index finger and carefully remove it from the port, as Step 4 shown in Figure 2-12. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-30...
  • Page 85 Protect your line card by inserting clean SFP module cage covers into the optical module cage when Step 6 there is no SFP module installed. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-31...

  • Page 86: Mylar Tab Sfp Or Sfp+ Module

    Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line card by firmly pushing on each SFP module. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-32...

  • Page 87: Removing A Mylar Tab Sfp Or Sfp+ Module

    SFP module from the port in a parallel direction. Do not twist or pull the tab, because you might disconnect it from the SFP module. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-33...

  • Page 88: Actuator Button Sfp Or Sfp+ Module

    Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line card by firmly pushing on each SFP module. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-34...

  • Page 89: Removing An Actuator Button Sfp Or Sfp+ Module

    Gently press the actuator button on the front of the SFP module until it clicks and the latch mechanism activates, releasing the SFP module from the port (Figure 2-18). Figure 2-18 Removing an Actuator Button SFP or SFP+ Module from a Port Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-35...

  • Page 90: Slide Tab Sfp Or Sfp+ Module

    Attach an ESD-preventive wrist or ankle strap and follow its instructions for use. Step 1 Line up the SFP module with the port and gently push on it until it snaps into the slot tightly Step 2 (Figure 2-20). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-36...

  • Page 91: Removing A Slide Tab Sfp Or Sfp+ Module

    With your thumb, push the slide tab on the bottom front of the SFP module in the direction of the line Step 4 card to disengage the module from the line card port (Figure 2-21). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-37...
  • Page 92 Protect your line card by inserting clean SFP module cage covers into the optical module cage when Step 7 there is no SFP module installed. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-38...

  • Page 93: Installing And Removing Xfp Modules

    Physical Contact (PC) or Ultra-Physical Contact (UPC) polished face types. The dual LC connector on the XFP transceiver modules does not support network interface cables with an Angle Polished Connector (APC) polished face type. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-39...

  • Page 94: Installing A 10-Gigabit Ethernet Xfp Transceiver Module

    Latch the XFP transceiver in the transceiver socket by pivoting the bale clasp down so that the bale clasp Step 7 is perpendicular to the transceiver body (Figure 2-24). If the latch is not fully engaged, you may accidentally disconnect the XFP transceiver. Caution Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-40...

  • Page 95: Removing A 10-Gigabit Ethernet Xfp Transceiver Module

    If you are removing an XFP transceiver, follow these steps: Step 1 Disconnect the network interface cable from the XFP transceiver connectors. Immediately reinstall the dust plug in the fiber-optic cable LC connector. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-41...
  • Page 96 Immediately place the XFP transceiver in an antistatic bag. Step 4 Figure 2-25 Removing the 10-Gigabit Ethernet XFP Transceiver A/ L A/ L A/ L A/ L Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-42...

  • Page 97: Cabling A 10-Gigabit Ethernet Xfp Transceiver

    Immediately attach the network interface cable LC connectors to the XFP transceiver module (Figure 2-26) for an illustration of cabling the XFP transceiver module). Figure 2-26 Cabling a10-Gigabit Ethernet XFP Transceiver Module A /L A /L Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-43...

  • Page 98: Overview

    Cisco 100-Gigabit Ethernet CFP Transceiver Modules Installation This section provides the installation, cabling, and removal instructions for the Cisco 100-Gigabit C Form-factor Pluggable (CFP) transceiver modules. The modules are hot-swappable input/output (I/O) devices that connect the system’s module port electrical circuitry with either a copper or a fiber-optic network.
  • Page 99 (Min) CFP-100G-ER4 100GBASE-ER, 2.9 per lane 4.5 per lane Four lanes: 1310-nm SMF (Max) (Max) 1295.6 -2.9 per lane –20.9 per lane 1300.1 (Min) (Min) 1304.6 1309.1 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-45...

  • Page 100: Required Tools

    Align the CFP device into the transceiver port socket of your networking module, and slide it in until the Step 4 CFP transceiver EMI gasket flange makes contact with the module faceplate (Figure 2-28). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-46...
  • Page 101 Seating the CFP Transceiver Module in the Socket Gently tighten the two captive installation screws on the transceiver to secure the CFP transceiver in the Step 6 socket (Figure 2-30). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-47...
  • Page 102 Cleaning Fiber-Optic Connectors, page 2-73. Figure 2-31 Cabling an Optical CFP Transceiver Module with SC Connectors SC connector L I N Network interface cable L I N Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-48...

  • Page 103: Removing The Cfp Transceiver

    Loosen the two captive installation screws that secure the CFP to the networking module. Step 2 Slide the CFP transceiver out of the module socket (Figure 2-32). Immediately place the CFP transceiver Step 3 in antistatic protective packaging. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-49...
  • Page 104 Installing Line Cards in the Cisco ASR 9000 Series Router Removing the CFP Transceiver Figure 2-32 Removing a CFP Transceiver Module Captive installation screws Optical bore dust plugs Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-50...

  • Page 105: Cisco 40-Gigabit Qsfp+ Transceiver Modules Installation

    SFP+ modules. Figure 2-33 40-Gigabit QSFP+ Transceiver Module (Optical) 40GBASE QSFP+ transceiver body Electrical connection to the module circuitry Bail-clasp latch Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-51...

  • Page 106: Specifications

    50.0 2000 100 m (328 ft) 50.0 4700 150 m (492 ft) QSFP-40G-LR4= 1271 G.652 10km 1291 1311 1331 QSFP-40GE-LR4= 1271 G.652 10 km 1291 1311 1331 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-52...

  • Page 107: Qsfp+ 38-Pin Connector Specifications

    (Min) (Min) 1331 QSFP-40GE-LR4= 40GBASE-LR4 2.3 per lane 2.3 per lane Four wavelengths (Max) (Max) 1271, 1291, –7 per lane –13.7 per lane 1311 (Min) (Min) 1331 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-53...

  • Page 108: Installing The 40-Gigabit Qsfp+ Transceiver Module

    Align the QSFP+ transceiver in front of the module’s transceiver socket opening and carefully slide the QSFP+ transceiver into the socket until the transceiver makes contact with the socket electrical connector. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-54...
  • Page 109 Press firmly on the front of the QSFP+ transceiver with your thumb to fully seat the transceiver in the Step 7 module’s transceiver socket (Figure 2-35). Caution If the latch is not fully engaged, you might accidentally disconnect the QSFP+ transceiver module. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-55...

  • Page 110: Attaching The Optical Network Cable

    – Grasp the MPO connector only by the housing to plug or unplug a fiber-optic cable. 40-Gigabit QSFP+ transceiver modules are keyed to prevent incorrect insertion. Note Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-56...

  • Page 111: Removing The 40-Gigabit Qsfp+ Transceiver Module

    QSFP+ transceiver modules or coming into contact with modules. To remove a QSFP+ transceiver, follow these steps: For optical QSFP+ transceivers, disconnect the network interface cable from the QSFP+ transceiver Step 1 connector. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-57...
  • Page 112 Grasp the tab and gently pull to release the transceiver from the socket. Slide the transceiver out of the socket. Place the QSFP+ transceiver into an antistatic bag. Step 4 Figure 2-37 Removing the 40-Gigabit QSFP+ Transceiver Module Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-58...

  • Page 113: Installing And Removing Cisco Cpak Transceiver Modules

    • single-mode fiber (SMF). • Cisco CPAK 100GBASE-SR10: Supports link lengths of up to 100 m and 150 m on laser-optimized OM3 and OM4 multifiber cables, respectively. • Cisco CPAK 10x10G-LR module: Supports link lengths of up to 10 km over standard single-mode fiber (SMF).

  • Page 114: Cpak Module Cabling Specifications

    Top row, left to right: Fibers are numbered 12 through 1. Fibers 11, 10, 9, 8, 7, 6, 5, 4, 3, 2 are used • for the optical Rx signals (Channel 9 through 0). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-60...

  • Page 115: Required Tools

    Check the label on the CPAK transceiver module to verify that you have the correct model for your Step 3 network. Remove the optical bore dust plug and set it aside. Step 4 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-61...

  • Page 116: Attaching The Optical Network Cable

    The CPAK-10X10G-LR module can only use network interface cables with the angle-polished contact (APC) face type (typical of singlemode fiber MPO assemblies). Cisco also provides a fiber optic breakout panel The breakout panel is an enclosure used to protect and Note manage fiber optic cables on the Cisco ASR 9000 Series Routers.

  • Page 117: Removing The Cpak Transceiver Module

    Grasp the tab and gently pull straight out to release the transceiver from the socket. Slide the transceiver out of the socket. Step 4 Place the CPAK transceiver into an antistatic bag. Step 5 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-63...

  • Page 118: Line Card Cable Management

    Excessive bending of interface cables can damage the cables. Caution Cable Management Tray A cable-management tray is mounted at the top of the Cisco ASR 9010 Router chassis for routing interface cables to the RSP and line cards. Figure 2-40 shows a typical cable routing through the cable-management tray.

  • Page 119: Router Cable Management Brackets

    3 in slot 3 in a Cisco ASR 9010 Router. Router Cable Management Brackets The Cisco ASR 9006 Router provides for a cable management bracket on each side of the router chassis. Figure 2-41 shows a typical cable routing for the Cisco ASR 9006 Router.

  • Page 120: Line Card Cable Management Bracket

    Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-66...

  • Page 121: Installing A Line Card Cable Management Bracket

    Insert and tighten the captive screw(s) to secure the bracket to the line card (Figure 2-43). Starting with the port on the line card closest to the bracket, connect each interface cable to the intended Step 4 port (Figure 2-42). Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-67...

  • Page 122: Removing A Line Card Cable-Management Bracket

    (TX) and laser receive (RX)—and an electrical interface (to the line card). The SFP+ modules used on the 16-Port 10GE oversubscribed line card are enhanced SFP modules. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-68...
  • Page 123 If your environment requires the light to travel close to the typical maximum distance, you should use an optical time domain reflectometer (OTDR) to measure the power loss. Use only the SFP and SFP+ modules supplied by Cisco Systems, Inc. with your Ethernet line card. Each Caution...

  • Page 124: Gigabit Ethernet Xfp Modules

    LC-type connectors to connect an Ethernet interface on the line card in your Cisco ASR 9000 Series Router to another Ethernet interface, router, or switch. Fiber optic cables are not available from Cisco Systems. They can be purchased from cable vendors. Note The following types of cables are used with line cards to connect your router to another router or switch: Single-mode—Generally yellow in color.

  • Page 125: Installing And Removing Fiber-Optic Interface Cables

    2-45) or one duplex LC connector (Figure 2-46). Optical fiber cables are available from cable vendors. These cables are not available from Cisco. Note Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.

  • Page 126: Removing Fiber-Optic Interface Cables

    Step 4 Detach the line card cable management bracket and optical fiber cable bundle from the line card and Step 5 place it carefully out of the way. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-72...

  • Page 127: Cleaning Fiber-Optic Connectors

    If you detect any contamination, repeat Step 1 Step For more information about cleaning fiber-optic connectors, as well as SFP/XFP transceivers, see Inspection and Cleaning Procedures for Fiber- Optic Connections. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-73...

  • Page 128: Type Rj-45 10/100/1000Base-T Copper Cables

    Disconnect the interface cable connectors from the line card interface ports. You do not have to remove the interface cables from the line card cable-management bracket. Note Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-74...
  • Page 129 Step 3 Detach the line card cable management bracket and optical fiber cable bundle from the line card and Step 4 place it carefully out of the way. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-75...
  • Page 130 Chapter 2 Installing Line Cards in the Cisco ASR 9000 Series Router Cables and Connectors Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 2-76...

  • Page 131: Verifying And Troubleshooting The Line Card Installation

    During a typical line card boot process, the following events occur: The line card receives power and begins executing initialization software. The line card performs internal checks, and prepares to accept the Cisco IOS XR software from the RSP. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 132: Status Leds

    Green Line card has booted properly, and is ready to pass or is passing traffic. Steady Amber Line card boot process is underway. When the Cisco IOS XR software finishes loading, the LED turns green. Blinking Amber Software configuration error has occurred that prevents the line card from passing traffic.

  • Page 133: Modular Port Adapter Leds

    If the Card Status LED goes on when the line card is installed in the new slot, suspect a failed backplane port in the original line card slot. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 134: Configuring And Troubleshooting Line Card Interface Cards

    If an error message displays on the console terminal during the line card initialization, see the appropriate reference publication for error message definitions. If you experience other problems that you cannot solve, contact a Cisco service representative for assistance. If you perform online insertion or removal of the SFP or XFP module without shutting down the Note interface, a warning message is displayed on the console device.

  • Page 135: Line Card Interface Address

    Instance numbers are reserved for cards that have subslots. This parameter is currently always 0 (zero) for line cards in the Cisco ASR 9000 Series. The ports on the line card are numbered 0, 1, 2, and so on. For example, the rack/slot/instance/port address of the fourth port of a line card installed in line card slot 1 is 0/1/0/3.

  • Page 136: Verifying The Transceiver Modules

    Step 7 If you want to disable the Cisco Discovery Protocol (CDP), which is not required, use this command: RP/0/RSP0/CPU0:router(config-if)# no cdp Add any other configuration subcommands required to enable routing protocols and adjust the interface Step 8 characteristics.
  • Page 137 NAME: "module 0/4/CPU0", DESCR: "8-Port 10GE DX Line Card, Requires XFPs" PID: A9K-8T/4-B , VID: V1D, SN: FOC123081JA NAME: "module mau 0/4/CPU0/0", DESCR: "Multirate 10GBASE-LR and OC-192/STM-64 S" PID: XFP-10GLR-OC192SR , VID: V02, SN: ONT1207108S RP/0/RSP0/CPU0:router# Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 138 NAME: "module mau GigabitEthernet0/2/CPU0/10", DESCR: "10GBASE-LR SFP+ Module for SMF" PID: SFP-10G-LR , VID: N/A, SN: ECL121900JJ NAME: "module mau GigabitEthernet0/2/CPU0/14", DESCR: "10GBASE-LR SFP+ Module for SMF" PID: SFP-10G-LR , VID: N/A, SN: ECL121900JR RP/0/RSP0/CPU0:router Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 139: Advanced Line Card Troubleshooting

    This information is required when working on issues with the Cisco Technical Assistance Center (Cisco TAC). For examples of how to use these commands and the resulting output, see the Cisco ASR 9000 Series Troubleshooting Guide. It is important to collect the show tech-support command data before doing a reload or power cycle.

  • Page 140: Regulatory, Compliance, And Safety Information

    Class 1 Laser Product Warning (Single-mode) Class 1 Laser Product. Statement 1008 Warning Class 1 LED Product Warning (Multimode) Class 1 LED Product (Multimode). Statement 123 Warning Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide 3-10...

  • Page 141: Appendix

    A P P E N D I X Technical Specifications This appendix lists the specifications for the Ethernet line cards for the Cisco ASR 9000 Series Aggregation Services Router. Cisco ASR 9000 Series Routers Environmental Specifications, page A-2 • Cisco Fast Ethernet and Gigabit Ethernet SFP Modules, page A-3 •...

  • Page 142: Cisco Asr 9000 Series Routers Environmental Specifications

    Ethernet line cards using GLC-GE-100FX SFP transceiver modules are installed in the router. This is due to the lower temperature specifications of the SFP module. Please contact a Cisco representative for more information. 2. Short term operating temperature specifications for the router will differ from those listed in this table when the 16-port 10-Gigabit Ethernet line card is installed in the router because of the lower temperature specifications of the SFP+ modules that are used in this line card.

  • Page 143: Cisco Fast Ethernet And Gigabit Ethernet Sfp Modules

    Cisco representative for more information. 2. GLC-FE-100EX, GLC-FE-100ZX, GLC-BX40-D-I, GLC-BX40-U-I, GLC-BX40-DA-I, GLC-BX80-D-I, and GLC-BX80-U-I SFP transceiver modules are supported on the 20-Port Gigabit Ethernet Modular Port Adapter only. Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 144: Cisco 10-Gigabit Ethernet Sfp+ Transceiver Modules

    Cisco SFP+ for 10-Gigabit 1310 nm 6.21 miles (10 km) Ethernet Long Reach ONS-SC+-10G-ZR Cisco SFP+ for 10-Gigabit 1550 nm 49.72 miles Ethernet Far Reach (80 km) 10G Copper SFP Cables Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 145: Cisco 100-Gigabit Ethernet Cpak Modules

    When using the SFP-10G-SR module, the maximum altitude is 5905 ft (1800 m). When using the SFP-10G-LR or SFP-10G-ER modules, the maximum altitude is sea level. These SFP+ transceiver modules are not supported on the A9K-4T16GE-TR and A9K-4T16GE-SE line cards in Cisco IOS XR software release 5.3.0. Cisco 100-Gigabit Ethernet CPAK Modules Table A-4 lists the supported Cisco 100-Gigabit Ethernet CPAK modules.

  • Page 146: Cisco 40-Gigabit Ethernet Cfp Modules

    Multirate 40-Gigabit Ethernet / 40G OTU3 1295.56 nm -LR4 1300.05 nm 1304.58 nm 1309.14 nm QSFP-40GE-LR4 Multirate 40-Gigabit Ethernet only - LR4 1295.56 nm 1300.05 nm 1304.58 nm 1309.14 nm Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 147: Cisco Dwdm Sfp Transceiver Modules

    1538.19 nm DWDM-SFP-3739 1000BASE-DWDM SFP (100 GHz ITU grid) 1537.39 nm DWDM-SFP-3661 1000BASE-DWDM SFP (100 GHz ITU grid) 1536.61 nm DWDM-SFP-3582 1000BASE-DWDM SFP (100 GHz ITU grid) 1535.82 nm Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...

  • Page 148: Cisco Dwdm Sfp+ Transceiver Modules

    Cisco IOS XR software to identify and validate the SFP module to operate properly with Cisco Ethernet line cards. Unapproved SFP modules (those not purchased directly from Cisco Systems, Inc.) do not work on the Ethernet line card. To verify the version of the installed SFP module, see Verifying the Transceiver Modules, page 3-6.

  • Page 149: Cisco Dwdm Sfp+ Transceiver Modules

    10G SFP+, 100 GHz, LC 1537.4 49.72 miles (80 km) ONS-SC+-10G-EP38.1 10G SFP+, 100 GHz, LC 1538.1 49.72 miles (80 km) ONS-SC+-10G-EP38.9 10G SFP+, 100 GHz, LC 1538.9 49.72 miles (80 km) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide...
  • Page 150 1559.7 49.72 miles (80 km) ONS-SC+-10G-EP60.6 10G SFP+, 100 GHz, LC 1560.6 49.72 miles (80 km) ONS-SC+-10G-EP61.4 10G SFP+, 100 GHz, LC 1561.4 49.72 miles (80 km) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-10...

  • Page 151: Cisco Dwdm Sfp+ Fixed Transceiver Modules

    10GBASE-DWDM, 1554.13nm, SFP10G (100-GHz ITU grid) 1554.13nm DWDM-SFP10G-54.94= 10GBASE-DWDM, 1554.94nm, SFP10G (100-GHz ITU grid) 1554.94nm DWDM-SFP10G-55.75= 10GBASE-DWDM, 1555.75nm, SFP10G (100-GHz ITU grid) 1555.75nm DWDM-SFP10G-56.55= 10GBASE-DWDM, 1556.55nm, SFP10G (100-GHz ITU grid) 1556.55nm Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-11...

  • Page 152: Cisco Dwdm Xfp Transceiver Modules

    31.1 miles (50 km) ONS-XC-10G-EP48.5 10G MR, XFP, 100 GHz, LC 1548.5 31.1 miles (50 km) ONS-XC-10G-EP49.3 10G MR, XFP, 100 GHz, LC 1549.3 31.1 miles (50 km) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-12...

  • Page 153: Cisco Cwdm Sfp Transceiver Modules

    CWDM SFP for Gigabit Ethernet and 1G/2G FC 1570 nm Orange CWDM-SFP-1590 CWDM SFP for Gigabit Ethernet and 1G/2G FC 1590 nm CWDM-SFP-1610 CWDM SFP for Gigabit Ethernet and 1G/2G FC 1610 nm Brown Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-13...

  • Page 154: Cisco 10-Gigabit Ethernet Cwdm Sfp+ Transceiver Modules

    24.85 miles (40 km) OC-192/STM-64 IR-2 XFP, low power (2.5W) XFP-10GZR-OC192LR Multirate 10GBASE-ZR and 1550 nm 49.70 miles (80 km) (Version V02, see note) OC-192/STM-64 LR-2 XFP Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-14...

  • Page 155: Cisco Dwdm Xfp Transceiver Modules

    DWDM-XFP-43.73 10GBASE-DWDM XFP (100 GHz ITU grid) 1543.73 nm DWDM-XFP-42.94 10GBASE-DWDM XFP (100 GHz ITU grid) 1542.94 nm DWDM-XFP-42.14 10GBASE-DWDM XFP (100 GHz ITU grid) 1542.14 nm Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-15...
  • Page 156 DWDM-XFP-C 10GBASE-DWDM Tunable XFP (50-GHz ITU grid) 80 Variable Variable Channels The DWDM-XFP-C module is not supported in the 4-Port 10 Gigabit Ethernet modular port adapter. Note Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-16...

  • Page 157: Ethernet Line Card Power Consumption Values

    8-Port 100-Gigabit Ethernet Line Card 1050 W at 77 F (25 ° ° 1100 W at 104 F (40 ° ° 1150 W at 131 F (55 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-17...
  • Page 158 Modular 4-NPU Line Card (-TR or -SE) 520 W at 77 F (25 ° ° 590 W at 104 F (40 ° ° 620 W at 131 F (55 Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-18...

  • Page 159: Ethernet Line Card Physical Dimensions

    8.16466 +/- .2268 kg 24-Port 10GE Line Card, A9K-24X10GE-TR 14 inches 1.72 inches 20.5 inches 18.42 pounds Packet Transport Optimized 35.56 cm 4.37 cm 52.07 cm 8.3551715 kg Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-19...
  • Page 160 160 Gigabyte Modular Line A9K-MOD160-SE 14 inches 1.72 inches 20.5 inches 16.34 pounds Card, Service Edge 35.56 cm 4.37 cm 52.07 cm 7.4117 kg Optimized (without EPs) Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide A-20...

Table of Contents