1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. A9K-SIP-700
  6. Hardware installation manual

Cisco A9K-SIP-700 Hardware Installation Manual

Aggregation services router sip and spa
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco ASR 9000 Series Aggregation Services Router SIP and SPA
Hardware Installation Guide
First Published: 2013-08-15
Last Modified: 2018-03-23
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883

Advertisement

Table of Contents
loading

Related Manuals for Cisco A9K-SIP-700

Summary of Contents for Cisco A9K-SIP-700

  • Page 1 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide First Published: 2013-08-15 Last Modified: 2018-03-23 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
  • Page 2 Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com trademarks.

  • Page 3: Table Of Contents

    Overview: Cisco ASR 9000 Series Router Shared Port Adapters SPA Summary Checking Hardware and Software Compatibility 2-Port Channelized OC-12/DS0 SPA Overview 2-Port Channelized OC-12/DS0 SPA LEDs 2-Port Channelized OC-12/DS0 SPA Interface Specifications Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 4 4-Port Channelized T3 to DS0 Overview 4-Port Channelized T3 to DS0 LEDs 4-Port Channelized T3 to DS0 Interface Specifications 4-Port Channelized T3 to DS0 Cables and Connectors 8-Port Channelized T1/E1 SPA Overview Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 5 2-Port OC-3 STM-1/OC-12 STM-4 POS SPA LEDs 2-Port OC-3 STM-1/OC-12 STM-4 POS SPA Interface Specifications 2-Port OC-3 STM-1/OC-12 STM-4 POS SPA Optical Transceiver Modules and Cables 4-Port OC-3 STM-1/OC-12 STM-4 POS SPA Overview Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 6 Preparing to Install a Shared Port Adapter or a SPA Interface Processor Safety Guidelines Safety Warnings Electromagnetic Compatibility Regulatory Statements Electrical Equipment Guidelines Telephone Wiring Guidelines Laser/LED Safety Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 7 C H A P T E R 6 Troubleshooting the Installation Troubleshooting the SIP Using debug Commands Packing a SIP for Shipment Packing a SPA for Shipment Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 8 Contents Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide viii...

  • Page 9: Changes To This Document

    March 2018 Adds support for the following SPA: • SPA-4XT-Serial 4-Port Serial Interface SPA March 2014 Adds support for the following SPA: • SPA-8XCHT1/E1-V2 8-Port Channelized T1/E1 SPA Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 10 1-Port Channelized OC-3 ATM CEoP SPA April 2011 Adds descriptions and installation instructions for the following SPAs: • SPA-4XCT3/DS0 4-Port Channelized T3 to DS0 • SPA-8XCHT1/E1 8-Port Channelized T1/E1 SPA Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 11: Objectives

    This document describes the shared port adapters (SPAs) and SPA Interface Processors (SIPs) that are supported on Cisco ASR 9000 Series Routers. This document also describes how to install the supported SIPs and SPAs and how to troubleshoot the installation.

  • Page 12: Organization

    Provides information for troubleshooting the installation of SIPs and SPAs. Related Documentation This section refers you to other documentation that also might be useful as you configure your Cisco ASR 9000 Series Router. The documentation listed below is available online.

  • Page 13: Obtaining Documentation And Submitting A Service Request

    What's New in Cisco Product Documentation, at: http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html. Subscribe to What's New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation as an RSS feed and delivers content directly to your desktop using a reader application. The RSS feeds are a free service, and Cisco currently supports RSS Version 2.0.
  • Page 14 Preface Obtaining Documentation and Submitting a Service Request Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 15: Overview: Cisco Asr 9000 Series Router Spa Interface Processors

    C H A P T E R Overview: Cisco ASR 9000 Series Router SPA Interface Processors This chapter describes the SPA interface processors (SIPs) that are supported on the Cisco ASR 9000 Series Aggregation Services Routers and contains the following sections: •...

  • Page 16: Router Hardware Installation

    Cisco ASR 9000 SIP-700 SIPs are supported on all Cisco ASR 9000 Series Routers. SIP Summary Summary descriptions of all SIPs supported on the Cisco ASR 9000 Series Router are shown in the following table. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 17: Sip Software And Hardware Compatibility

    For software configuration information, refer to the Cisco IOS XR software configuration and command reference publications for the installed Cisco IOS XR release. Also refer to the Cisco IOS XR software release notes for additional information. The following table lists the Cisco IOS XR releases that are compatible with supported SIPs.

  • Page 18: Cisco Asr 9000 Sip-700 Overview

    • A9K-SIP-700 supports 4 GB of memory. • A9K-SIP-700-8G supports 8 GB of memory. Both types of Cisco ASR 9000 SIP-700 are identical in appearance and can be identified by the PID located on the faceplate of the SIP The following sections describe the Cisco ASR 9000 SIP-700: Cisco ASR 9000 SIP-700 Board Components The main Cisco ASR 9000 SIP-700 board components are shown in the figure below.

  • Page 19: Cisco Asr 9000 Sip-700 Physical Specifications

    Bay 3 (Bottom Left) Bay 1 (Bottom Right) The following figure shows a Cisco ASR 9000 SIP-700 with 2 SPAs installed. The left SPA slot is subslot 0 and the right SPA slot is subslot 1. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 20: Spa Interface Addresses On The Cisco Asr 9000 Sip-700

    SIP slot number, SPA subslot, and port number on the SPA, in the format rack/slot/subslot/port . Subslots and ports are numbered starting from 0, so each Cisco ASR 9000 SIP-700 has two subslots 0 (left) and 1 (right). For example, the interface addresses of a 2-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 in rack 0 are 0/3/1/0 and 0/3/1/1.
  • Page 21 Cisco ASR 9010 10-slot chassis. Figure 5: Slot, Subslot, and Port Locations for the 2-Port Channelized OC-12/DS0 SPA on a Cisco ASR 9010 Chassis Table 9: Slot and Port Locations for the 2-Port Channelized OC-12/DS0 SPA in Slot 3...
  • Page 22 Overview: Cisco ASR 9000 Series Router SPA Interface Processors SPA Interface Addresses on the Cisco ASR 9000 SIP-700 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 23: Overview: Cisco Asr 9000 Series Router Shared Port Adapters

    4-Port Serial Interface SPA Overview, on page 66 SPA Summary The following table shows the summary descriptions of the SPAs that are supported on the Cisco ASR 9000 Series Aggregation Services Router. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 24 SPA-1CHOC3-CE-ATM 1-Port Channelized OC-3 ATM CEoP 1 OC3 4.2.0 single-height SPA-1XOC3-ATM-V2 1-Port and 3-Port Clear Channel OC-3 1 or 3 OC3 4.2.0 ATM SPA SPA-3XOC3-ATM-V2 single-height Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 25: Checking Hardware And Software Compatibility

    SPA FPD images. Checking Hardware and Software Compatibility To check the minimum software requirements of Cisco IOS XR software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs or SPAs within a system are compatible, but it does provide the minimum Cisco IOS XR requirements for individual hardware modules or components.

  • Page 26: 2-Port Channelized Oc-12/Ds0 Spa Overview

    Note Access to this tool is limited to users with Cisco.com login accounts. To access Software Advisor, click Login at Cisco.com, type Software Advisor in the SEARCH box, and click GO. Click the link for the Software Advisor tool. Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware.

  • Page 27: 2-Port Channelized Oc-12/Ds0 Spa Interface Specifications

    SONET single-mode and multimode optical fiber connection. (See the following figure.) Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port Channelized OC-12/DS0 SPA supports the following types of optical transceiver modules: •...

  • Page 28: 1-Port Channelized Stm-16/Oc-48 Spa Overview

    1-Port Channelized STM-16/OC-48 SPA LEDs The 1-Port Channelized STM-16/OC-48 SPA has two types of LEDs: an A/L LED for the port and a STATUS LED, as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 29: 1-Port Channelized Stm-16/Oc-48 Spa Interface Specifications

    STS-48/STM-16 frame. HDLC and Frame-Relay are also supported. The main operational mode of the framer is OC-48, where each one of the 48 Paths can carry a DS3 and each DS3 can carry 28 DS1s. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 30: 1-Port Channelized Stm-16/Oc-48 Spa Cables And Connectors

    1-Port Channelized STM-16/OC-48 SPA-equipped routers back to back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 31: 1-Port Oc-48 Pos Rpr Spa Overview

    STATUS LED Note The WRAP, PASSTHRU, and MATESYNC LEDs apply to the SPA in RPR/SRP mode only. The 1-Port OC48-POS/RPR SPA LEDs are described in the following table. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 32 Port is enabled by software, and loopback is on. STATUS SPA power off. Green SPA is ready and operational. Amber SPA power is on and good, and the SPA is being configured. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 33: 1-Port Oc48-Pos/Rpr Spa Interface Specifications

    2-Port OC-48 POS RPR SPA Overview The following sections describe the 2-Port OC48-POS/RPR SPA: 2-Port OC48-POS/RPR SPA LEDs The 2-Port OC48-POS/RPR SPA has five LEDs, as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 34 Off, even when the lamptest is performed. Green A node on the ring is wrapped. Green Blinking A node on the ring is steering pass-through Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 35: 2-Port Oc48-Pos/Rpr Spa Interface Specifications

    LC-type cable (see the below figure) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Figure 14: Duplex Patch Cable with LC-Type Connectors Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 36: 8-Port Oc-12 Stm-4 Pos Spa Overview

    Port is enabled by software, and there is a valid SONET signal without any alarms. Amber Port is enabled by software, and there is at least one alarm. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 37: 8-Port Oc12/Stm4 Spa Interface Specifications

    SONET and SDH single-mode and multimode optical fiber connections (see the below figure). Cisco Systems qualifies the optics that are approved for use with its SPAs. The following OC-12 optical transceiver modules are supported on the 8-Port OC12/STM4 SPA : •...

  • Page 38: Oc-12 Module Connections

    Figure 17: LC-Type Cable OC-12 Module Connections The following table shows the OC-12 specifications of the optics on the 8-Port OC-12c/STM-4 POS SPA. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 39: 1-Port Oc-192 Stm-64 Pos Rpr Xfp Spa Overview

    The following sections describe the 1-Port OC-192/STM-64 POS/RPR XFP SPA: 1-Port OC-192/STM-64 POS/RPR XFP SPA LEDs The 1-Port OC-192/STM-64 POS/RPR XFP SPA has six LEDs, as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 40 Port is not enabled by software. ACTIVE Green Port is enabled by software, and loopback is off. Amber Port is enabled by software, and loopback is on. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 41: 1-Port Oc-192/Stm-64 Pos/Rpr Xfp Spa Interface Specifications

    IP-aware optical transport, and simplified network operations. The Spatial Reuse Protocol (SRP) is a MAC-layer protocol developed by Cisco and is used in conjunction with Cisco DPT products, which use a pair of counter-rotating rings in an optimum fashion to provide improved bandwidth utilization over an equivalent SONET network.

  • Page 42: Oc-192 Module Connections

    The length of the cables allow only two possible connection scenarios, next slot horizontal and same slot vertical. This assumes that the chassis is mounted vertically. The following figure shows the mate cables used to connect the SPAs. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 43: 2-Port And 4-Port Clear Channel T3/E3 Spa Overview

    The RPR mate cable is necessary only when the SPA is to be used in RPR mode. It is not needed in POS mode. Support for the RPR feature is dependent on the platform software-release feature content. Verify support for the RPR feature support using SPA datasheets or by contacting your Cisco representative. 2-Port and 4-Port Clear Channel T3/E3 SPA Overview...

  • Page 44: 2-Port And 4-Port Clear Channel T3/E3 Spa Interface Specifications

    High-Level Data Link Control [HDLC]), and is mapped to T3 and E3 frames. The encapsulations add transport overhead to the packet of data frames before transporting, and are stripped when a packet is transported to the far end. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 45: 2-Port And 4-Port Clear Channel T3/E3 Spa Cables And Connectors

    • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) Note The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female BNC end). The 2-Port and 4-Port Clear Channel T3/E3 SPA Faceplate figure shows the connectors on the 2-Port and 4-Port Clear Channel T3/E3 SPA, and the following table describes the signal descriptions for these connectors.

  • Page 46: 4-Port Channelized T3 To Ds0 Interface Specifications

    The 4-Port Channelized T3 to DS0 interface is compliant with ANSI and Telco standards. The interface also provides support for Management Information Base (MIB) RFC 2495, RFC 2496, and T1.231. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 47: 4-Port Channelized T3 To Ds0 Cables And Connectors

    • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) Note The Cisco cable part numbers are 72-4124-01 (with Male BNC end) and 72-4131-01 (with Female BNC end). The previous figure shows the Siemax connectors on the 4-Port Channelized T3 to DS0, and the following table provides the signal descriptions for these connectors.

  • Page 48: 8-Port Channelized T1/E1 Spa Interface Specifications

    Shielded twisted pair (STP) T1/E1 cables must be used to comply with EN55022/CISPR22 Class A emissions requirements. For revisions 73-8358-05 through 73-8358-08 Shielded Twisted pair (STP) T1/E1 cables must be used to comply with FCC Class A emissions requirements. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 49: 8-Port Channelized T1/E1 Spa Cables, Connectors, And Pinouts

    1-Port Channelized STM-1/OC-3 SPA LEDs The 1-Port Channelized STM-1/OC-3 SPA has two types of LEDs: an A/L LED for the port and a STATUS LED, as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 50: 1-Port Channelized Stm-1/Oc-3 Spa Interface Specifications

    RFC 1662, PPP in HDLC-like Framing. The 1-Port Channelized STM-1/OC-3 SPA also provides support for SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB) II (RFC 1213). Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 51: 1-Port Channelized Stm-1/Oc-3 Spa Cables And Connectors

    Note The 1-Port Channelized STM-1/OC-3 SPA supports Frame Relay Fragmentation (FRF.12) and Multilink Frame Relay (MFR) features for Cisco IOS XR Software Release 4.0.1 and later releases. 1-Port Channelized STM-1/OC-3 SPA Cables and Connectors The 1-Port Channelized STM-1/OC-3 SPA uses a small form-factor pluggable (SFP) optical transceiver module installed in the port for SONET and SDH single-mode and multimode optical fiber connection (see the below figure).

  • Page 52: 4-Port Oc-3/Stm-1 Pos Spa Overview

    STATUS LED. The following figure shows the 4-Port OC-3/STM-1 POS SPA. Figure 28: 4-Port OC-3/STM-1 POS SPA Faceplate C/A (Carrier/Alarm) LED STATUS LED A/L (Active/Loopback) LED The following table describes the 4-Port OC-3/STM-1 POS SPA LEDs. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 53: 4-Port Oc-3/Stm-1 Pos Spa Interface Specifications

    SONET and SDH single-mode and multimode optical fiber connection (see the below figure). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 4-Port OC-3/STM-1 POS SPA supports the following types of optical transceiver modules: •...

  • Page 54: Oc-3 Module Connections

    OC-3 MM: 1270 nm to 1380 nmOC-3 SR: 1260 nm to 1360 nmOC-3 IR-1: 1261 nm to 1360 nmOC-3 LR-1: 1263 nm to1360 nmOC-3 LR-2: 1480 nm to 1580 nm Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 55: 8-Port Oc-3/Stm-1 Pos Spa Overview

    The 8-Port OC-3/STM-1 POS SPA has three types of LEDs: two LEDs for each port on the SPA and one STATUS LED. The following figure shows the 8-Port OC-3/STM-1 POS SPA faceplate. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 56: 8-Port Oc-3/Stm-1 Pos Spa Interface Specifications

    The 8-Port OC-3/STM-1 POS SPA interface complies with the following RFCs: • RFC 1662, PPP in HDLC-like Framing • RFC 2427, Multiprotocol Interconnect over Frame Relay • RFC 2615, PPP over SONET/SDH Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 57: 8-Port Oc-3/Stm-1 Pos Spa Optical Transceiver Modules And Cables

    SONET and SDH single-mode and multimode optical fiber connections (see the following figure). Cisco Systems qualifies the optics that are approved for use with its SPAs. The following OC-3 optical transceiver modules are supported on the 8-Port OC-3/STM-1 POS SPA: •...

  • Page 58: Oc-3 Module Connections

    The 1-Port Channelized OC-3 ATM CEoP SPA has three types of LEDs. There are two LEDs for the port on the SPA, and one STATUS LED as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 59: 1-Port Channelized Oc-3 Atm Ceop Spa Interface Specifications

    1-Port Channelized OC-3 ATM CEoP SPA Optical Transceiver Modules and Cables Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port Channelized OC-3 ATM CEoP SPA supports the following types of optical transceiver modules: Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 60: 1-Port And 3-Port Clear Channel Oc-3 Atm Spa Overview

    Port is enabled by software, and there is at least one alarm. Port is not enabled by software. Green Port is enabled by software, and loopback is off. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 61: 1-Port And 3-Port Clear Channel Oc-3 Atm Spa Interface Specifications

    For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 62: 1-Port Clear Channel Oc-12 Atm Spa Overview

    LED Label Color State Meaning Port is not enabled by software. Green Port is enabled by software, and there is a valid SONET signal without any alarms. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 63: 1-Port Clear Channel Oc-12 Atm Spa Interface Specifications

    SONET/SDH-compliant interface with an average wavelength of 1530 nm. The multimode transceiver provides a full-duplex, 622.08-Mbps, LED-based SONET/SDH-compliant interface with an average wavelength of 1325 nm. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 64: 2-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Overview

    When SFP modules are replaced, the SPA interface retains any previously-defined configurations. This includes settings for IP address, clock source, loopback, CRC, and POS flags. The 2-Port OC-3 STM-1/OC-12 STM-4 POS SPA is a half rate SPA. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 65: 2-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Leds

    (155.52 Mbps) and OC-12 line rates (622.08 Mbps). Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the layer 2 frame. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 66: 2-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Optical Transceiver Modules And Cables

    SONET and SDH single-mode and multimode optical fiber connection (see the below figure). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port OC-3 STM-1/OC-12 STM-4 POS SPA when configured as OC-3 supports the following types of optical transceiver modules: •...

  • Page 67: 4-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Overview

    For more information about SPAs and their compatibility with SIPs and modular optics, see the “SIP and SPA Product Overview” chapter in this guide. The following sections describe the 4-Port OC-3 STM-1/OC-12 STM-4 POS SPA: Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 68: 4-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Leds

    The 4-Port OC-3 STM-1/OC-12 STM-4 POS SPA interface complies with the following IETF RFCs: • RFC 1662, PPP in HDLC-like Framing • RFC 2427, Frame Relay Encapsulation • RFC 2615, PPP over SONET/SDH Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 69: 4-Port Oc-3 Stm-1/Oc-12 Stm-4 Pos Spa Optical Transceiver Modules And Cables

    SONET and SDH single-mode and multimode optical fiber connection (see the figure below). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 4-Port OC-3 STM-1/OC-12 STM-4 POS SPA when configured as OC-3 supports the following types of optical transceiver modules: •...

  • Page 70: 4-Port Oc-48/Stm-16 Pos/Rpr Spa Overview

    The 4-Port OC-48/STM-16 POS/RPR SPA has five types of LEDs: four LEDs for each port on the SPA and one STATUS LED, as shown in the following figure. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 71: 4-Port Oc-48/Stm-16 Pos/Rpr Spa Interface Specifications

    OC-48-equipped routers back to back. The 4-Port OC-48/STM-16 POS/RPR SPA supports the following types of optical transceiver modules: • Single-mode short-reach (SR) SFP module—SFP-OC48-SR OC48/STM16c Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 72: Oc-48 Module Connections

    This assumes that the chassis is mounted vertically. The following figure shows the mate cables used to connect the SPAs. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 73: 2-Port Channelized T3/E3 Atm Ceop Spa Overview

    LEDs for each port on the SPA, and a single STATUS LED for the SPA. Figure 50: 2-Port Channelized T3/E3 ATM CEoP SPA Faceplate TX (Transmit) connector A/L (Active/Loopback) Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 74: 2-Port Channelized T3/E3 Atm Ceop Spa Interface Specifications

    • CAB-T3E3-RF-BNC-M (T3 or E3 Cable, 1.0/2.3 RF to mini BNC-Male, 10 feet) • CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to mini BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 75: 24-Port Channelized T1/E1/J1 Ceop Spa Overview

    24-Port Channelized T1/E1/J1 CEoP SPA Overview Note The Cisco cable part numbers are 72-4124-01 (for the male BNC end) and 72-4131-01 (for the female BNC end). A SPA can receive data over the cable up to a maximum distance of 1350 ft (411.5 meters).

  • Page 76: 24-Port Channelized T1/E1/J1 Ceop Spa Interface Specifications

    This connector has thumbscrews that should be screwed into the SPA when the cable is installed. 24-Port Channelized T1/E1/J1 CEoP SPA Cables and Connectors The 24-Port Channelized T1/E1/J1 CEoP SPA requires a Cisco cable (part number CABLE-24T1E1J1), which is shown in the figure below. Figure 52: 24-Port Channelized T1/E1/J1 CEoP SPA High-Density Cable...

  • Page 77: Spa Cable Pinouts

    Not connected Line 6 TX TipTX Ring Not connected RX TipRX Ring 3181 Not connected Not connected Line 7 TX TipTX Ring RX TipRX Ring 3282 Not connected Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 78 2171 2045 Not connected RX TipRX Ring 4595 Not connected 2045 Not connected Line 21 TX TipTX Ring 2272 2146 RX TipRX Ring 4696 Not connected 2146 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 79: Rj-45 Cable Pinouts

    24-Port Channelized T1/E1/J1 CEoP SPA Patch Panel A 24-port channelized T1/E1/J1 CEoP SPA patch panel with the DCC2484/25T1-S part number is available from Optical Cable Corporation (OCC) at: http://www.occfiber.com/main/index.php Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 80: 4-Port Serial Interface Spa Overview

    Overview: Cisco ASR 9000 Series Router Shared Port Adapters 4-Port Serial Interface SPA Overview This is a shielded rack mount 24-port patch panel, 2RU, accessory component for the Cisco PID SPA-24CHT1-CE-ATM. You can view the image of patch panel with the DCC2484/25T1-S part number at: http://www.occfiber.com/main/index.php?m=1&p=2&s=Y&l=en&it=54&i=193...

  • Page 81: 4-Port Serial Interface Spa Interface Specifications

    4-Port Serial Interface SPA Cables, Connectors, and Pinouts The 4-Port Serial Interface SPA uses Smart Serial cable interfaces that support one of two serial interface ports: DTE or DCE. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 82 X.21 DCE Female CAB-SS-530MT EIA/TIA-530 DTE Male CAB-SS-530FC EIA/TIA-530 DCE Female CAB-SS-530AMT EIA/TIA-530A DTE Male CAB-SS-530AFC EIA/TIA-530A DCE Female The following figure shows the Smart Serial cable connectors. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 83 Serial Interface SPA ports. Table 43: Smart Serial Connector Pinouts Signal Signal O_TXD/RXD+ O_TXD/RXD- O_TXCE/RXC+ O_TXCE/RXC- B_TXC/TXC+ B_TXC/TXC- I_RXC/TXCE+ I_RXC/TXCE- I_RXD/TXD+ I_RXD/TXD- B_DCD/DCD+ B_DCD/DCD- O_DTR/DSR+ O_DTR/DSR- O_RTS/CTS+ MODE2 O_RTS/CTS- MODE1 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 84 Twisted pair no. 7 <—— J2-15 DB(A), TxC+ J1-16 IO_TxC/RxC– <—— J2-12 DB(B), TxC– J1-4 I_RxC/TxCE+ Twisted pair no. 8 <—— J2-17 DD(A), RxC+ J1-17 I_RxC/TxCE– <—— J2-9 DD(B), RxC– Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 85 Twisted pair no. ——> J2-6 CC(A), DSR+ J1-20 O_DTR/DSR- ——> J2-22 CC(B), DSR- J1-6 IO_DCD/DCD+ Twisted pair no. ——> J2-8 CF(A), DCD+ J1-19 IO_DCD/DCD- ——> J2-10 CF(B), DCD- Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 86 Twisted pair no. 1 ——> J2-4 CA(A), RTS+ J1-9 O_RTS/CTS- ——> J2-19 CA(B), RTS- J1-11 I_CTS/RTS+ Twisted pair no. 4 <—— J2-5 CB(A), CTS+ J1-10 I_CTS/RTS- <—— J2-13 CB(B), CTS- Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 87 Twisted pair no. 5 <—— J2-2 BA(A), TxD+ J1-18 I_RxD/TxD- <—— J2-14 BA(B), TxD- J1-1 O_TxD/RxD+ Twisted pair no. 9 ——> J2-3 BB(A), RxD+ J1-14 O_TxD/RxD- ——> J2-16 BB(B), RxD- Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 88 Any pin not referenced is not connected. Table 48: EIA/TIA-232 DTE Cable Pinouts (DB-25 Male Connector) Signal Description Direction Signal J1-23 MODE_0 Local connections J1-24 MODE_DCE Shield J2-1 Shield Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 89 Table 49: EIA/TIA-232 DCE Cable Pinouts (DB-25 Female Connector) Signal Description Direction Signal J1-23 MODE_0 Local connections Shield J2-1 Shield J1-5 I_RxD/TxD Twisted pair no. <—— J2-2 J1-18 — Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 90 MODE_DCE —> J2-20 J1-1 O_TxD/RxD+ Twisted pair no. 5 ——> J2-4 J1-14 O_TxD/RxD- ——> J2-22 J1-3 B_TxC/TxC+ Twisted pair no. 7 <—— J2-5 J1-16 B_TxC/TxC- <—— J2-23 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 91 Description Direction Signal Shield — J2-1 Shield J1-22 MODE_1 Twisted pair no. 2 J2-19 J2-20 J1-5 I_RxD/TxD+ Twisted pair no. 5 <—— J2-4 J1-18 I_RxD/TxD- <—— J2-22 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 92 Any pin not referenced is not connected. Table 52: V.35 DTE Cable Pinouts (34-Pin Male Connector) Signal Description Direction Signal J1-22 MODE_1 Local connections J1-23 MODE_0 J1-24 MODE_DCE Shield — J2-A Shield Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 93 Table 53: V.35 DCE Cable Pinouts (34-Pin Female Connector) Signal Description Direction Signal J1-22 MODE_1 Local connections J1-23 MODE_0 Shield — J2-A Shield J1-11 I_CTS/RTS+ Twisted pair no. <—— J2-C J1-12 I_DSR/DTR+ <—— J2-H Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 94 Signal Description Direction Signal J1-21 MODE_1 Local connections J1-24 MODE_0 Shield — J2-1 Shield J1-1 O_TxD/RxD+ Twisted pair no. ——> J2-2 Transmit+ J1-14 O_TxD/RxD- ——> J2-9 Transmit- Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 95 Control- J1-1 O_TxD/RxD+ Twisted pair no. ——> J2-4 Receive+ J1-14 O_TxD/RxD- ——> J2-11 Receive- J1-8 O_CTS/RTS+ Twisted pair no. ——> J2-5 Indication+ J1-9 O_CTS/RTS- ——> J2-12 Indication- Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 96 4-Port Serial Interface SPA Cables, Connectors, and Pinouts Signal Description Direction Signal J1-2 O_RxC/TxCE+ Twisted pair no. ——> J2-6 Timing+ J1-15 O_RxC/TxCE- ——> J2-13 Timing- J1-26 Circuit GND Twisted pair no. — J2-8 Circuit Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 97: Preparing To Install A Shared Port Adapter Or A Spa Interface Processor

    • Do not wear loose clothing, jewelry, or other items that could get caught in the router while working with line cards. • Cisco equipment operates safely when it is used in accordance with its specifications and product usage instructions.

  • Page 98: Electromagnetic Compatibility Regulatory Statements

    Figure 56: Laser Warning Labels for Single-Mode Port Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 99: Preventing Electrostatic Discharge

    Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI) shielding is an integral component of the line card. Cisco recommends using an ESD-preventive strap whenever you are handling network equipment or one of its components.
  • Page 100 Preparing to Install a Shared Port Adapter or a SPA Interface Processor Required Tools and Equipment • ESD-preventive wrist or ankle strap and instructions • Interface cables to connect the SIP with another router or switch Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 101: Installing And Removing A Spa Interface Processor

    (EMI) emissions requirements and to allow proper airflow across the installed modules. If you plan to install an SIP in a slot that is not in use, you must first remove the blank. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 102: Removing And Installing A Sip

    Installing a SIP, on page 90 Note Some of the procedures in the following sections use illustrations of a 10-slot Cisco ASR 9000 Series Router to support the descriptions of removing and installing SIPs. Although the card cages of Cisco ASR 9000 Series Aggregation Services Routers differ, the designated use of slots and the process of installing and removing a SIP are basically the same.

  • Page 103: Removing A Sip

    Step 3 Detach the SIP cable-management bracket from the SIP. Step 4 Use a screwdriver to loosen the captive screw at each end of the SIP faceplate. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 104: Installing A Sip

    Note Refer to Figure 2-6 Cisco ASR 9010 Router Components and Slot Numbering and Figure 2-7 Cisco ASR 9006 Router Components and Slot Numbering in the Unpacking and Installing the Chassis chapter of the Cisco ASR 9000 Series Aggregation Services Router Hardware Installation Guide for information on line card slot types in order to determine an appropriate slot in which to install the SIP.
  • Page 105 To ensure adequate space for additional SIPs, always tighten the captive installation screws on each newly Caution installed SIP before you insert any additional SIPs. These screws also prevent accidental removal and provide proper grounding and EMI shielding for the router. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 106 If you are replacing a SIP install the SPAs in the same bays as you noted in Step 2 under the Removing a SIP, on page section. Step 9 Install the interface cables. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 107: Installing And Removing A Shared Port Adapter

    C H A P T E R Installing and Removing a Shared Port Adapter This chapter describes how to install or remove SPAs on the Cisco ASR 9000 Series Aggregation Services Router. This chapter contains the following sections: • Handling SPAs, on page 93 •...

  • Page 108: Online Insertion And Removal

    Online Insertion and Removal Online Insertion and Removal Cisco ASR 9000 Series Router SIPs and SPAs support online insertion and removal (OIR). SPAs can be inserted or removed independently from the SIP. OIR of a SIP with installed SPAs is also supported.

  • Page 109: Optical Device Installation And Removal

    Inspection, cleaning, and reinspection are critical steps to take before making fiber-optic connections. Cleaning Optical Devices Refer to the Inspection and Cleaning Procedures for Fiber-Optic Connections document for information on cleaning optical devices. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

  • Page 110: Checking The Installation

    Step 2 When the SIP and SPA STATUS LEDs are green, all associated interfaces are configurable. Refer to Cisco ASR 9000 Series Router Getting Started Guide and Cisco ASR 9000 Series Router Interface and Hardware Component Configuration Guide for configuration instructions.

  • Page 111: Using Show Commands To Verify Sip And Spa Status

    Use the hw-module fpd location <rack/slot/subslot> command to verify the FPD version information of the SPAs installed in the system. If a SPA does not meet the minimum version required, the FPD may need to be updated. Refer to Cisco ASR Note 9000 Series Aggregation Services Router System Management Configuration Guide for instructions.
  • Page 112 The SPA will slide easily into the slot if it is properly aligned on the tracks. If the SPA does not slide easily, do NOT force it. Remove the SPA and reposition it, paying close attention to engaging it on the tracks. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...
  • Page 113 Step 5 If the SPA is new and is not a replacement, configure the new SPA using the instructions in Cisco IOS XR Getting Started Guide for the Cisco ASR 9000 Series Router and Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Configuration Guide .

  • Page 114: Using The Ping Command To Verify Network Connectivity

    After you verify that the system and the SIP have booted successfully and are operational, you can use this command to verify the status of the SPA ports. Refer to Cisco ASR 9000 Series Aggregation Services Router Getting Started Guide and Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Configuration Guide for more information on bringing up and configuring the Cisco ASR 9000 Series Router and the Cisco ASR 9000 SIP-700 or Cisco ASR 9000 SIP-500.

  • Page 115: Troubleshooting The Installation

    C H A P T E R Troubleshooting the Installation This chapter describes how to troubleshoot the installation of SIPs and SPAs on the Cisco ASR 9000 Series Aggregation Services Router. This chapter contains the following sections: • Troubleshooting the SIP, on page 101 •...

  • Page 116: Packing A Sip For Shipment

    • Larger exterior carton • Two packing cushions Caution The Cisco Systems original packaging is to be used for the shipment of all SIPs. Failure to properly use Cisco Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card.

  • Page 117: Packing A Spa For Shipment

    • Thermoform container (transparent plastic-molded clamshell) • Carton Caution The Cisco Systems original packaging is to be used for the shipment of all SPAs and cable-management brackets. Failure to properly use Cisco Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card.
  • Page 118 Troubleshooting the Installation Packing a SPA for Shipment Step 6 Apply tape over the carton flap to ensure the carton stays closed during shipping. Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide...

This manual is also suitable for:

Asr 9000 sip-700Asr 9000 seriesA9k-sip-700-8g

Table of Contents