Operating Other Manufacturers' Video Equipment - JVC RX-9000VBK Instructions Manual

Operating Other Manufacturers' Video Equipment

This remote control supplied with the receiver can transmit control
signals for other manufacturers' VCRs, TVs, CATV converters,
DBS tuners, and DVD players. By changing the transmittable
signals from preset ones to the other manufacturers', you can
operate the other manufacturer's components using this remote
control.
When operating the other manufacturers' components, refer also to
the manuals supplied with them. To operate these components with
the remote control, first you need to set the manufacturer's code
each for VCR, TV, CATV converter, DBS tuner, and DVD player.
MAIN SUB
ROOM ROOM ON
STANDBY
MAIN ROOM SUB ROOM TV/CATV/DBS VCR 1
ON/OFF ON/OFF POWER POWER
DVD DVD MUILTI CD TAPE/MD
TV/DBS VIDEO PHONO FM/AM
VCR 1 CDR/VCR 2 ANALOG/DIGITAL SLEEP
SURROUND CNTR TONE CENTER
1 2 3
ON/OFF
MENU MENU
REAR TONE REAR-L
SURROUND
4 5 6
MODE
ENTER ENTER
CD-DISC SEA MODE REAR-R
7 8 9
/P
SOUND TEST SUBWOOFER
0
10 +10
100+
RETURN FM MODE
AUDIO/
TV/VCR
MENU
CATV/DBS
SET
TEXT
EXIT
DISPLAY
TV VOL CHANNEL VOLUME
TV/VIDEO VCR 1 TAPE/MD MUTING
CONTROL
/REW PLAY FF/
DOWN TUNING UP
REC STOP PAUSE
RM-SRX9000J REMOTE CONTROL
IMPORTANT:
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 10 feet
(3 m).
60
AUDIO/
TV/VCR
CATV/DBS
Check to see if the remote
control mode selector is set
to the correct position.
To operate the audio
system, TVs, and VCRs,
set it to "AUDIO/TV/VCR."
To operate the CATV
converter, DBS tuner, and
DVD player, set it to "CATV/
DBS."
To change the transmittable signals for
operating another manufacturer's TV
1. Set the remote control mode to "AUDIO/TV/
VCR."
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer's code (two digits) using
buttons 1–9, and 0.
See the list on page 62 to find the code.
Examples: For a JVC product, press 2, 8.
For a Sanyo product, press 2, 5.
5. Release TV/CATV/DBS POWER.
The following buttons can be used for operating the TV (with
the remote control mode selector set to "AUDIO/TV/VCR"):
TV POWER Turns on and off the TV.
TV VOL +/–
Adjusts the volume.
TV/VIDEO
Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector
set to "AUDIO/TV/VCR"), you can perform the following
operations on a TV:
CHANNEL +/–
Changes the channels.
1 – 10, 0, 100+ (+10) Selects the channels.
The 100+ (+10) button will function
as the ENTER button if your TV
requires pressing ENTER after
selecting a channel number.
6. Try to operate your TV by pressing TV/CATV/
DBS POWER.
When your TV turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Set the remote control mode to "CATV/DBS."
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer's code (two digits) using
buttons 1 – 9, and 0.
See the list on page 62 to find the code.
Examples: For a JVC product, press 5, 7.
For a Sony product, press 6, 5.