JVC RX-9000VBK Instructions Manual page 39

3) Repeat 1) and 2) to adjust the other
speaker output levels.
3. Adjust the center tone.
1) Press BALANCE/SURROUND
ADJUST repeatedly until "CENTER
TONE" appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the center
tone level you want.
• As you turn it, the display changes to
show the following:
CENTER SHARP1
CENTER FLAT
(Canceled)
CENTER SOFT 1
To make the dialogue clearer, select "CENTER SHARP1" (a
little) or "CENTER SHARP2" (much).
To make the dialogue softer, select "CENTER SOFT 1" (a
little) or "CENTER SOFT 2" (much).
When "CENTER FLAT" is selected, no adjustment is applied.
4. Adjust the rear tone.
1) Press BALANCE/SURROUND
ADJUST repeatedly until "REAR
TONE" appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the rear
tone level you want.
• As you turn it, the display changes to
show the following:
REAR SHARP1
REAR FLAT
(Canceled)
REAR SOFT 1
To make the rear sounds clearer, select "REAR SHARP1" (a
little) or "REAR SHARP2" (much).
To make the rear sounds softer, select "REAR SOFT 1" (a
little) or "REAR SOFT 2" (much).
When "REAR FLAT" is selected, no adjustment is applied.
5. Adjust the overall level of the effects.
1) Press BALANCE/SURROUND
ADJUST repeatedly until "EFFECT
LEVEL" appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the effect
level.
• As you turn it, the effect level changes
as follows:
EFFECT 1 EFFECT 2
EFFECT 5
As the number increases, the overall level of reflections applied
to the direct sounds increases. (Normally set it to "EFFECT 3.")
BALANCE/SURROUND
ADJUST
MULTI JOG
CENTER SHARP2
CENTER SOFT 2
BALANCE/SURROUND
ADJUST
MULTI JOG
REAR SHARP2
REAR SOFT 2
BALANCE/SURROUND
ADJUST
MULTI JOG
EFFECT 3
EFFECT 4
6. Adjust the room size (sense of
spaciousness).
1) Press BALANCE/SURROUND
ADJUST repeatedly until "ROOM
SIZE" appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the room
size.
• As you turn it, the room size changes as
follows:
ROOM SIZE 1 ROOM SIZE 2
ROOM SIZE 5
As the number increases, the interval between reflections
increases so that you will feel as if you were in a larger room.
(Normally set it to "ROOM SIZE 3.")
7. Adjust the liveness.
1) Press BALANCE/SURROUND
ADJUST repeatedly until
"LIVENESS" appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the liveness
effect.
• As you turn it, the liveness level
changes as follows:
LIVENESS 1
LIVENESS 5
As the number increases, the attenuation level of reflections over
time decreases so that acoustics change from "Dead" to "Live."
(Normally set it to "LIVENESS 3.")
From the remote control:
When using the remote control, you cannot adjust the effect level,
room size, and liveness. To adjust these parameters, use the buttons
and controls on the front panel.
1. Press SURROUND MODE
repeatedly until "LARGE
THEATER (or DIG L. THEATER,
DTS L. THEATER)" or "SMALL
THEATER (or DIG S. THEATER, DTS S.
THEATER)" appears on the display.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker
output balance.
"TEST TONE L" starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
TEST TONE L TEST TONE C
(Left front speaker) (Center speaker)
TEST TONE LS
(Left rear speaker)
BALANCE/SURROUND
ADJUST
MULTI JOG
ROOM SIZE 3
ROOM SIZE 4
BALANCE/SURROUND
ADJUST
MULTI JOG
LIVENESS 2 LIVENESS 3
LIVENESS 4
SURROUND
MODE
SOUND
TEST
10
RETURN
TEST TONE R
(Right front speaker)
TEST TONE RS
(Right rear speaker)
Continued to the next page.
37