Dodge 1997 Neon WIRING DIAGRAMS Owner's Manual page 146

PL
GENERAL INFORMATION
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 7
DESCRIPTION AND OPERATION
FOG LAMPS (FRONT) . . . . . . . . . . . . . . . . . . . . 8
GENERAL INFORMATION
INTRODUCTION
The headlamp switch has 3 positions, ON, PARK
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
DESCRIPTION AND OPERATION
PARKING LAMPS
Circuit A3 in the Power Distribution Center (PDC)
connects to a bus bar in the fuse block. One of the
four circuits powered by the bus bar is circuit F33.
Circuit F33 connects to the headlamp switch. A 40
amp fuse in the PDC protects the A3 circuit. A 15
amp fuse, in cavity 2 of the fuse block, protects the
F33 circuit.
The headlamp switch has 3 positions, ON, PARK
(tail lamps) and OFF, plus a dimmer switch. When
the headlamp switch is in the PARK or ON position,
the switch connects circuit F33 to circuit L7. From
the headlamp switch, circuit L7 branches to power
the front parking lamps and rear tail lamps, lavalier
lamps, side marker lamps, and rear license plate
lamp.
GROUND CIRCUIT
Circuit Z1 provides ground for the parking lamps,
headlamps, lavalier lamps, tail lamps, side marker
lamps and rear license plate lamp although different
grounding points are used. Circuit Z1 also provides
the ground path for the headlamps and turn signals.
HELPFUL INFORMATION
• Check for a blown 40 amp fuse in the PDC.
• Check for a blown fuse in cavity 2 of the fuse
block.
• For the left front parking lamp, turn signal, side
marker lamp and left headlamp, the Z1 circuit
8W - 50 FRONT LIGHTING
8W-50 FRONT LIGHTING
INDEX
page
grounding point is the left side of the radiator closure
panel.
side marker lamp and right headlamp, the Z1 circuit
grounding point is in the right fender side shield.
ON position, the dimmer circuit, F33, also connects
to circuit E1. Circuit E1 powers the ash receiver
lamp, transmission range indicator lamp, instrument
panel cluster illumination lamps, HVAC control
lamp, heated rear window lamp, and radio lamp. A 4
amp fuse, in cavity 12 of the fuse block, protects cir-
cuit E1.
HEADLAMPS
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
HEADLAMP SWITCH IN OFF OR PARKING
LAMP POSITION
Center (PDC) and supplies battery voltage for the
headlamp switch. A 40 amp fuse protects the A3 cir-
cuit. The headlamp switch has an internal 24 amp
circuit breaker that connects circuit A3 to either the
L2 or L20 circuits, depending on switch position.
switch feeds the L20 circuit that connects to the
multi-function switch. Circuit L20 powers the high
beam circuit when the operator flashes the head-
lamps with the turn signal stalk of the multi-func-
tion
headlamps with the stalk, the multi-function switch
connects the L20 circuit to the L3 circuit. The L3 cir-
cuit feeds the high beam of the headlamps.
HEADLAMP SWITCH IN ON POSITION
it connects the A3 circuit from the PDC to circuit L2.
HEADLAMP LEVELING MOTORS . . . . . . . . . . . . 8
HEADLAMPS . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PARKING LAMPS . . . . . . . . . . . . . . . . . . . . . . . . 7
• For the right front parking lamp, turn signal,
• Circuit L7 also feeds the radio, if equipped.
• When the headlamp switch is in the PARK or
The headlamp switch has 3 positions, ON, PARK
Circuit A3 originates in the Power Distribution
In the OFF and PARK positions the headlamp
switch. When
When the headlamp switch is in the ON position,
8W - 50 - 7
the operator flashes
page
the