Page 1: Wiring Diagrams
WIRING DIAGRAMS 8W - 1 WIRING DIAGRAMS CONTENTS page page 8W-01 GENERAL INFORMATION ..8W-01-1 8W-48 REAR WINDOW DEFOGGER ..8W-48-1 8W-02 COMPONENT INDEX ... 8W-02-1 8W-50 FRONT LIGHTING .
Page 3: Connector/Ground Locations
8W - 01 GENERAL INFORMATION 8W - 01 - 1 8W-01 GENERAL INFORMATION INDEX page page DESCRIPTION AND OPERATION INTERMITTENT AND POOR CONNECTIONS . . . 6 CIRCUIT IDENTIFICATION ....3 TROUBLESHOOTING TESTS .
Page 4: Notes, Cautions, And Warnings
8W - 01 - 2 8W - 01 GENERAL INFORMATION DESCRIPTION AND OPERATION (Continued) NOTES, CAUTIONS, and WARNINGS WARNING: ALWAYS REMOVE RINGS, WATCHES, LOOSE HANGING JEWELRY, AND LOOSE CLOTH- Throughout this group additional important infor- ING. mation is presented in three ways; Notes, Cautions, and Warnings.
Page 5: Circuit Identification
8W - 01 GENERAL INFORMATION 8W - 01 - 3 DESCRIPTION AND OPERATION (Continued) CIRCUIT IDENTIFICATION All circuits in the diagrams use an alpha/numeric code to identify the wire and its function (Fig. 3). To identify which circuit code applies to a system, refer to the Circuit Identification Code Chart.
Page 6 8W - 01 - 4 8W - 01 GENERAL INFORMATION DESCRIPTION AND OPERATION (Continued) Fig. 5 Symbol Identification...
Page 7: Fasteners
8W - 01 GENERAL INFORMATION 8W - 01 - 5 DESCRIPTION AND OPERATION (Continued) ELECTROSTATIC DISCHARGE (ESD) SENSITIVE DEVICES All ESD sensitive components are solid state and a symbol (Fig. 6) is used to indicate this. When han- dling any component with this symbol comply with the following procedures to reduce the possibility of electrostatic charge build up on the body and inad- vertent discharge into the component.
Page 8: Troubleshooting Tests
8W - 01 - 6 8W - 01 GENERAL INFORMATION DIAGNOSIS AND TESTING (Continued) • Voltmeter - Used to check for voltage on a cir- • Wire insulation that has rubbed through causing cuit. Always connect the black lead to a known good a short to ground •...
Page 9: Troubleshooting Wiring Problems
8W - 01 GENERAL INFORMATION 8W - 01 - 7 DIAGNOSIS AND TESTING (Continued) (3) Connect the other lead to the other end of the (4) The voltmeter will show the difference in volt- circuit being tested. Low or no resistance means good age between the two points.
Page 10: Fusible Link Replacement
8W - 01 - 8 8W - 01 GENERAL INFORMATION SERVICE PROCEDURES (Continued) (2) Remove 1 inch of insulation from each end of ment this indicates a problem in the charging/start- the wire. ing system that needs to be corrected. (3) Place a piece of heat shrink tubing over one Replacement of the fusible link is the same as side of the wire.
Page 11: Connector And Terminal Replacement
8W - 01 GENERAL INFORMATION 8W - 01 - 9 SERVICE PROCEDURES (Continued) CONNECTOR REPLACEMENT (1) Disconnect battery. (2) Disconnect the connector that is to be repaired from its mating half/component (3) Remove connector locking wedge, required (Fig. 16) Fig. 17 Terminal Removal Fig.
Page 12: Terminal Replacement
8W - 01 - 10 8W - 01 GENERAL INFORMATION SERVICE PROCEDURES (Continued) (8) Place a piece of heat shrink tubing over one side of the wire. Be sure the tubing will be long enough to cover and seal the entire repair area. (9) Spread the strands of the wire apart on each part of the exposed wires.
Page 13: Diode Replacement
8W - 01 GENERAL INFORMATION 8W - 01 - 11 SERVICE PROCEDURES (Continued) DIODE REPLACEMENT SPECIAL TOOLS (1) Disconnect the battery. WIRING/TERMINAL (2) Locate the diode in the harness, and remove the protective covering. (3) Remove the diode from the harness, pay atten- tion to the current flow direction (Fig.
Page 15 8W - 02 COMPONENT INDEX 8W - 02 - 1 8W-02 COMPONENT INDEX INDEX page SCHEMATICS AND DIAGRAMS ............1 GENERAL INFORMATION .
Page 16 8W - 02 - 2 8W - 02 COMPONENT INDEX Component Page Component Page Intermittent Wipe/Wash Switch ... 8W-53 Repeater Lamps ....8W-50, 52 Key-In Switch .
Page 17 8W - 02 COMPONENT INDEX 8W - 02 - 3 8W-02 COMPONENT INDEX GENERAL INFORMATION INTRODUCTION This section provides an alphabetical listing of all the components covered in group 8W. For information on system operation, refer to the appropriate section of the wiring diagrams.
Page 19 8W - 10 POWER DISTRIBUTION 8W - 10 - 1 8W-10 POWER DISTRIBUTION INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 31 8W - 10 POWER DISTRIBUTION 8W - 10 - 13 8W-10 POWER DISTRIBUTION DESCRIPTION AND OPERATION This section covers the power distribution center and all circuits involved with it. For additional infor- mation on system operation, refer to the appropriate wiring diagrams.
Page 33 8W - 11 FUSE/FUSE BLOCK 8W - 11 - 1 8W-11 FUSE/FUSE BLOCK INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 47 8W - 11 FUSE/FUSE BLOCK 8W - 11 - 15 8W-11 FUSE/FUSE BLOCK DESCRIPTION AND OPERATION This section covers the fuse block and all circuits involved with it. For additional information on sys- tem operation, please refer to the appropriate section of the wiring diagrams.
Page 49 8W - 15 GROUND DISTRIBUTION 8W - 15 - 1 8W-15 GROUND DISTRIBUTION INDEX page SCHEMATICS AND DIAGRAMS ............1 GENERAL INFORMATION .
Page 58 8W - 15 - 10 8W - 15 GROUND DISTRIBUTION 8W-15 GROUND DISTRIBUTION GENERAL INFORMATION This section identifies the grounds, splices that connect to those grounds, and the components that connect those grounds. For additional information on system operation, refer to the appropriate section of the wiring diagrams.
Page 59 8W - 20 CHARGING SYSTEM 8W - 20 - 1 8W-20 CHARGING SYSTEM INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 61 8W - 20 CHARGING SYSTEM 8W - 20 - 3 8W-20 CHARGING SYSTEM DESCRIPTION AND OPERATION When there is current present in the field, and the rotor is turning, the stator in the generator produces CHARGING SYSTEM a B+ voltage that is supplied to the battery through the A11 and A0 circuits.
Page 63 8W - 21 STARTING SYSTEM 8W - 21 - 1 8W-21 STARTING SYSTEM INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 65 8W - 21 STARTING SYSTEM 8W - 21 - 3 8W-21 STARTING SYSTEM STARTING SYSTEM (AUTOMATIC TRANSMISSION) DESCRIPTION AND OPERATION The Power Distribution Center (PDC) supplies bat- STARTING SYSTEM- MANUAL TRANSMISSION tery voltage to the engine starter motor solenoid The Power Distribution Center (PDC) supplies bat- through circuit T40 when the coil side of the engine tery voltage to the engine starter motor solenoid starter motor relay energizes.
Page 67 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 1 8W-30 FUEL/IGNITION SYSTEMS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 80 8W - 30 - 14 8W - 30 FUEL/IGNITION SYSTEMS 8W-30 FUEL/IGNITION SYSTEMS INDEX page page DESCRIPTION AND OPERATION IGNITION SWITCH ..... . 14 AUTOMATIC SHUT DOWN RELAY .
Page 81 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 15 DESCRIPTION AND OPERATION (Continued) HELPFUL INFORMATION HELPFUL INFORMATION • Refer to group 14 Fuel System, for additional Circuit Z12 which supplies ground for the PCM high current drivers, has the same termination point information.
Page 82 8W - 30 - 16 8W - 30 FUEL/IGNITION SYSTEMS DESCRIPTION AND OPERATION (Continued) • Crankshaft position sensor Circuit K4 connects to cavity 43 of the PCM connec- • Camshaft position sensor tor. • Battery temperature sensor • Throttle position sensor HELPFUL INFORMATION •...
Page 83 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 17 DESCRIPTION AND OPERATION (Continued) is a variable resistor. As coolant temperature MANIFOLD ABSOLUTE PRESSURE SENSOR changes, the resistance in the sensor changes causing From the Powertrain Control Module (PCM), cir- a change in current draw.
Page 84 8W - 30 - 18 8W - 30 FUEL/IGNITION SYSTEMS DESCRIPTION AND OPERATION (Continued) KNOCK SENSOR the ASD relay on circuit K51. Circuit K51 connects to cavity 67 of the PCM connector. The knock sensor provides an input to the Power- Circuit A142 supplies voltage for the fuel injectors.
Page 85 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 19 DESCRIPTION AND OPERATION (Continued) • Circuit K39 connects to cavity 57 of the PCM In the START or RUN position, the ignition switch connector. connects circuit A1 from the fuse block and circuit •...
Page 86 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 19 DESCRIPTION AND OPERATION (Continued) EGR TRANSDUCER (EET) SOLENOID This circuit connects to cavity 23 of the PCM connec- tor. Circuit F12 supplies battery voltage to the EET The G4 circuit is also used for the fuel gauge solenoid.
Page 88 8W - 35 ANTI-LOCK BRAKES 8W - 35 - 1 8W-35 ANTI-LOCK BRAKES INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 93 8W - 35 - 6 8W - 35 ANTI-LOCK BRAKES 8W-35 ANTI-LOCK BRAKES INDEX page page DESCRIPTION AND OPERATION BRAKE SWITCH INPUT ....7 ABS PUMP MOTOR RELAY .
Page 94 8W - 35 ANTI-LOCK BRAKES 8W - 35 - 7 DESCRIPTION AND OPERATION (Continued) WHEEL SPEED SENSORS DATA LINK CONNECTOR There are four wheel speed sensors, one at each Circuit D21 is used for diagnostics of a fault with wheel. The sensors use a tone wheel to determine the ABS system.
Page 96 8W - 40 INSTRUMENT CLUSTER 8W - 40 - 1 8W-40 INSTRUMENT CLUSTER INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 102 8W - 40 INSTRUMENT CLUSTER 8W - 40 - 7 8W-40 INSTRUMENT CLUSTER INDEX page page DESCRIPTION AND OPERATION INSTRUMENT CLUSTER ....7 AIRBAG WARNING LAMP .
Page 103 8W - 40 - 8 8W - 40 INSTRUMENT CLUSTER DESCRIPTION AND OPERATION (Continued) FUEL GAUGE level sending unit (circuit G4) it illuminates the lamp. The fuel level gauge is connected to the fuel pump module on the G4 circuit. The fuel pump module con- HEADLAMP ON CHIME tains the fuel pump and a variable resistor for the The headlamp ON chime is used to indicate to the...
Page 104 8W - 40 INSTRUMENT CLUSTER 8W - 40 - 9 DESCRIPTION AND OPERATION (Continued) RIGHT AND LEFT TURN SIGNAL INDICATORS brake system pressure is below a predetermined level the switch CLOSES and completes a path to ground These lamps are used to indicate to the operator from the G9 circuit at the cluster, through the which turn signal is ON.
Page 106 8W - 41 HORNS/CIGAR LIGHTER 8W - 41 - 1 8W-41 HORNS/CIGAR LIGHTER INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 109 8W - 41 - 4 8W - 41 HORNS/CIGAR LIGHTER 8W-41 HORNS/CIGAR LIGHTER DESCRIPTION AND OPERATION HELPFUL INFORMATION • Check the 15 amp fuse in the PDC. • Press the horn switch and listen for the horn HORNS relay to click. A clicking relay indicates voltage is The horn system is powered by a 15 amp fuse present up to the switch.
Page 110 8W - 42 AIR CONDITIONING-HEATER 8W - 42 - 1 8W-42 AIR CONDITIONING-HEATER INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 115 8W - 42 - 6 8W - 42 AIR CONDITIONING-HEATER 8W-42 AIR CONDITIONING-HEATER INDEX page page DESCRIPTION AND OPERATION BLOWER MOTOR OPERATION ... . . 6 A/C OPERATION ......6 HELPFUL INFORMATION .
Page 116 8W - 42 AIR CONDITIONING-HEATER 8W - 42 - 7 DESCRIPTION AND OPERATION (Continued) • Check the 10 amp fuse located in the PDC for except, the C5 circuit is used for the M1 speed and circuit C6 is used for M2 speed operation. the A/C compressor clutch relay.
Page 118 8W - 43 AIRBAG SYSTEM 8W - 43 - 1 8W-43 AIRBAG SYSTEM INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 122 8W - 43 AIRBAG SYSTEM 8W - 43 - 5 8W-43 AIRBAG SYSTEM AIRBAG SQUIB (AIRBAG IGNITER) DESCRIPTION AND OPERATION AIRBAG CONTROL MODULE (ACM) DRIVERS SIDE AIRBAG Two circuits, R43 and R45, connect the ACM to the Two different circuits supply battery voltage from drivers side airbag module squib (igniter) after pass- the fuse block to the Airbag Control Module (ACM), ing through the clock spring connector.
Page 124 8W - 44 INTERIOR LIGHTING 8W - 44 - 1 8W-44 INTERIOR LIGHTING INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 128 8W - 44 INTERIOR LIGHTING 8W - 44 - 5 8W-44 INTERIOR LIGHTING INDEX page page DESCRIPTION AND OPERATION MAP/READING LAMPS ....6 ASH RECEIVER LAMP .
Page 129 8W - 44 - 6 8W - 44 INTERIOR LIGHTING DESCRIPTION AND OPERATION (Continued) The second ground path is through the headlamp ASH RECEIVER LAMP switch. Circuit M23 is spliced in with the time out The ash receiver lamp receives power on the E2 relay.
Page 130 8W - 47 AUDIO SYSTEMS 8W - 47 - 1 8W-47 AUDIO SYSTEMS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 134 8W - 47 AUDIO SYSTEMS 8W - 47 - 5 8W-47 AUDIO SYSTEMS INDEX page page DESCRIPTION AND OPERATION RADIO MEMORY ......5 HELPFUL INFORMATION .
Page 136 8W - 48 REAR WINDOW DEFOGGER 8W - 48 - 1 8W-48 REAR WINDOW DEFOGGER INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 138 8W - 48 REAR WINDOW DEFOGGER 8W - 48 - 3 8W-48 REAR WINDOW DEFOGGER DESCRIPTION AND OPERATION instrument panel right center support. The grid uses the grounding point at the rear body in the right REAR WINDOW DEFOGGER wheel house. When the system is in operation, a L.E.D.
Page 140 8W - 50 FRONT LIGHTING 8W - 50 - 1 8W-50 FRONT LIGHTING INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 146 8W - 50 FRONT LIGHTING 8W - 50 - 7 8W-50 FRONT LIGHTING INDEX page page GENERAL INFORMATION HEADLAMP LEVELING MOTORS ... . 8 INTRODUCTION ......7 HEADLAMPS .
Page 147 8W - 50 - 8 8W - 50 FRONT LIGHTING DESCRIPTION AND OPERATION (Continued) Circuit L2 connects to the multi- function switch and circuit L43 is protected by a 10 amp fuse located in feeds the L4 circuit (for low beam operation). The L4 the fuse block and is the feed for the left LOW beam circuit connects to a bus bar in the fuse block.
Page 148 8W - 51 REAR LIGHTING 8W - 51 - 1 8W-51 REAR LIGHTING INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 156 8W - 51 REAR LIGHTING 8W - 51 - 9 8W-51 REAR LIGHTING INDEX page page DESCRIPTION AND OPERATION STOP LAMPS ......10 BACK-UP LAMPS .
Page 157 8W - 51 - 10 8W - 51 REAR LIGHTING DESCRIPTION AND OPERATION (Continued) STOP LAMPS BACK-UP LAMPS Circuit F32 in the Power Distribution Center In the RUN position, the ignition switch connects (PDC) feeds the stop lamps. Circuit F32 connects to circuit A2 from the Power Distribution Center (PDC) the stop lamp switch.
Page 158 8W - 52 TURN SIGNALS 8W - 52 - 1 8W-52 TURN SIGNALS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 162 8W - 52 TURN SIGNALS 8W - 52 - 5 8W-52 TURN SIGNALS INDEX page page DESCRIPTION AND OPERATION TURN SIGNALS ......5 HAZARD FLASHERS .
Page 163 8W - 52 - 6 8W - 52 TURN SIGNALS DESCRIPTION AND OPERATION (Continued) Circuit L60 supplies voltage to the right front turn HELPFUL INFORMATION • For the left front turn signal/hazard flasher signal/hazard lamp. The L60 circuit splices to the instrument cluster to power the right indicator lamp.
Page 164 8W - 53 WIPERS 8W - 53 - 1 8W-53 WIPERS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 167 8W - 53 - 4 8W - 53 WIPERS 8W-53 WIPERS INDEX page page DESCRIPTION AND OPERATION WIPERS—INTERMITTENT ....4 HELPFUL INFORMATION ....4 As the windshield wiper motor turns, the park DESCRIPTION AND OPERATION switch internal to the motor moves from its grounded...
Page 168 8W - 60 POWER WINDOWS 8W - 60 - 1 8W-60 POWER WINDOWS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 170 8W - 60 POWER WINDOWS 8W - 60 - 3 8W-60 POWER WINDOWS INDEX page page DESCRIPTION AND OPERATION POWER WINDOWS ..... . 3 HELPFUL INFORMATION .
Page 172 8W - 61 POWER DOOR LOCKS 8W - 61 - 1 8W-61 POWER DOOR LOCKS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 176 8W - 61 POWER DOOR LOCKS 8W - 61 - 5 8W-61 POWER DOOR LOCKS INDEX page page DESCRIPTION AND OPERATION ENTRY ....... 5 HELPFUL INFORMATION .
Page 177 8W - 61 - 6 8W - 61 POWER DOOR LOCKS DESCRIPTION AND OPERATION (Continued) LEFT DOOR UNLOCK (USING RKE Ground for the motors is supplied on circuit P34 TRANSMITTER) through a bus bar in the right switch to circuit P36. When the operator selects left front UNLOCK the The P36 circuit connects from the switch to the RKE module energizes the left front unlock realy...
Page 178 8W - 62 POWER MIRRORS 8W - 62 - 1 8W-62 POWER MIRRORS INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 180 8W - 62 POWER MIRRORS 8W - 62 - 3 8W-62 POWER MIRRORS INDEX page page DESCRIPTION AND OPERATION POWER MIRRORS ..... . . 3 HELPFUL INFORMATION .
Page 182 8W - 64 POWER SUNROOF 8W - 64 - 1 8W-64 POWER SUNROOF INDEX page SCHEMATICS AND DIAGRAMS ............1 DESCRIPTION AND OPERATION .
Page 184 8W - 64 POWER SUNROOF 8W - 64 - 3 8W-64 POWER SUNROOF DESCRIPTION AND OPERATION The ground is passed through the switch to circuit Z8 and finally to ground. POWER SUNROOF When the operator selects the CLOSE function, power and ground are reversed. Power for the tilt and slide switches is supplied on circuit F10.
Page 186 8W - 70 SPLICE INFORMATION 8W - 70 - 1 8W-70 SPLICE INFORMATION INDEX page SCHEMATICS AND DIAGRAMS ............1 Component Page Component...
Page 190 8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 1 8W-80 CONNECTOR PIN-OUTS INDEX page SCHEMATICS AND DIAGRAMS ............1 Component Page Component...
Page 191 8W - 80 - 2 8W - 80 CONNECTOR PIN-OUTS Component Page Component Page Intermittent Wipe/Wash Switch ..8W-80-20 Left Rear Speaker ....8W-80-24 Key-In Switch .
Page 192 8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 3 Component Page Component Page Right Door Lock Switch ....8W-80-30 Right Repeater Lamp ....8W-80-33 Right Door Window Motor .
Page 226 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 1 8W-90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION number identification. Refer to the index for the proper figure number. INTRODUCTION CONNECTOR/GROUND LOCATIONS This section provides illustrations identifying the For items not shown in this section a N/S is placed general location of components, grounds, and connec- in the Fig.
Page 227 8W - 90 - 2 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued) Connector Color Location Fig. Connector Color Location Fig. Name/Number Name/Number Duty Cycle RT Strut Tower Headlamp Rear of Switch Evap/Purge Dimmer/Optical Solenoid Horn Switch Engine Coolant LT Side of Headlamp Switch Bottom of...
Page 228 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 3 DESCRIPTION AND OPERATION (Continued) Connector Color Location Fig. Connector Color Location Fig. Name/Number Name/Number Left Rear Shelf At Speaker Right Door Power At Switch Speaker Window Switch Left Rear Wheel LT Rear Frame Right Door Window At Motor...
Page 229 8W - 90 - 4 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued) Fig. 1 Airbag Impact Sensors Fig. 2 Brake Support Bracket Connections...
Page 230 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 5 DESCRIPTION AND OPERATION (Continued) Connector Color Location Fig. Connector Color Location Fig. Name/Number Name/Number Vapor Canister RT Front Fender Wiper/Washer Rear of Switch Leak Detector Switch Vehicle Speed Side of Battery WIndshield Washer Bottom of Control Servo...
Page 231 8W - 90 - 6 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 232 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 7 DESCRIPTION AND OPERATION (Continued)
Page 233 8W - 90 - 8 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 234 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 9 DESCRIPTION AND OPERATION (Continued)
Page 235 8W - 90 - 10 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 236 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 11 DESCRIPTION AND OPERATION (Continued)
Page 237 8W - 90 - 12 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued) Fig. 10 Cowl Panel Connections Fig. 11 Visor/Vanity Connections...
Page 238 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 13 DESCRIPTION AND OPERATION (Continued) Fig. 12 Steering Column Connections Fig. 13 Console Connections...
Page 239 8W - 90 - 14 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 240 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 15 DESCRIPTION AND OPERATION (Continued)
Page 241 8W - 90 - 16 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 242 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 17 DESCRIPTION AND OPERATION (Continued)
Page 243 8W - 90 - 18 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 244 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 19 DESCRIPTION AND OPERATION (Continued) Fig. 18 Door Connections (Front) Fig. 19 Door Connections (Rear)
Page 245 8W - 90 - 20 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued) Fig. 20 Body Connections (Left Rear) Fig. 21 Trunk Connections...
Page 246 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 21 DESCRIPTION AND OPERATION (Continued) Fig. 22 Decklid/Rear Bumper Connections Fig. 23 Fuel Tank Connections...
Page 247 8W - 90 - 22 8W - 90 CONNECTOR/GROUND LOCATIONS DESCRIPTION AND OPERATION (Continued) Fig. 24 Rear Lighting Connections...
Page 248: Description And Operation
8W - 95 SPLICE LOCATIONS 8W - 95 - 1 8W-95 SPLICE LOCATIONS SPLICE LOCATIONS DESCRIPTION AND OPERATION The following index covers all splices shown in the INTRODUCTION wiring diagrams. If a splice is not shown in this sec- This section provides illustrations identifying the tion, a N/S will be in the Fig.
Page 249 8W - 95 - 2 8W - 95 SPLICE LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 250 8W - 95 SPLICE LOCATIONS 8W - 95 - 3 DESCRIPTION AND OPERATION (Continued)
Page 251 8W - 95 - 4 8W - 95 SPLICE LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 252 8W - 95 SPLICE LOCATIONS 8W - 95 - 5 DESCRIPTION AND OPERATION (Continued)
Page 253 8W - 95 - 6 8W - 95 SPLICE LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 254 8W - 95 SPLICE LOCATIONS 8W - 95 - 7 DESCRIPTION AND OPERATION (Continued)
Page 255 8W - 95 - 8 8W - 95 SPLICE LOCATIONS DESCRIPTION AND OPERATION (Continued)
Page 256 8W - 95 SPLICE LOCATIONS 8W - 95 - 9 DESCRIPTION AND OPERATION (Continued)

Dodge 1997 Neon WIRING DIAGRAMS Owner's Manual

Quick Links

WIRING DIAGRAMS

Troubleshooting

Related Manuals for Dodge 1997 Neon WIRING DIAGRAMS

Summary of Contents for Dodge 1997 Neon WIRING DIAGRAMS

Table of Contents