Remote Control Unit - Pioneer VSX-808RDS Service Manual

VSX-808RDS

Remote Control Unit

These pages describe the buttons on the remote control
used to operate the receiver.
RECEIVER
1
2
3
MPX
ENTER
VOL
4
CHANNEL
5
MULTI CONTROL
DVD/LD TV/SAT
6
VCR 1
TV CONTROL
VCR 2
RECEIVER
DSP MODE
1 2
CH.SELECT TEST TONE
7
6
5
CH.LEVEL
9
0
FUNCTION DIRECT
8
MODE CHECK
9
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
1 RECEIVER button
Press to switch the receiver on or to put in standby.
2 MUTING button
Press to mute the volume. "MUTING" appears in the
display. Press again to cancel.
3 [When set to SURROUND]
%, fi, @, #, (Select/Adjust) buttons
[When set to other than OPERATIONS]
*(Pause), &(Stop), !(Rewind), ⁄(Fast Forward),
ENTER/‹(Play) buttons
[Tuner Operations]
FQ + (to higher frequencies), FQ – (to lower frequencies),
MPX, DISP MODE, # (FM/AM) buttons
MPX: Use to switch the auto stereo/monaural mode for
receiving FM broadcasts. When the received broadcast
signal is weak, press this button to set the monaural
mode.
DISP MODE: Use to switch the RDS data while listening
to an FM station. Each press changes the display in the
order of RT, PS, PTY, and frequency.
4 VOL (+/–) buttons
Press to adjust the volume. When VOL (+/–) buttons are
pressed while muting, muting is canceled.
5 CHANNEL (+/–) button
Use to select preset stations when operating the tuner.
When the remote is used to control other components,
this button may be used to change channels, tracks, or
chapters.
60
0
TV
-
FQ
+
DISP
MODE
–
FQ
VOL
CD
TUNER
=
MD/TAPE
MIDNIGHT
3 4
ATT SIG.SELECT
7 8
EFFECT
+10
MEMU
CLASS TV/VCR
FL DIMMER
~
COMMANDER
SET UP
!
Î
@
6 MULTI CONTROL buttons
Use these buttons to select the remote operation mode.
For example, pressing TUNER sets the remote to
operate the tuner functions.
7 Number buttons
These buttons can perform a variety of different functions
depending on the remote operation mode.
• [RECEIVER operations (press RECEIVER first)]
: Press repeatedly to select the standard mode, the
ADVANCED THEATER modes and MPEG mode.
DSP MODE : Press repeatedly to select a DSP sound
mode.
MIDNIGHT : Press to hear surround sound effectively at
low volumes.
CH.SELECT : Use to select a speaker when adjusting
speaker levels.
TEST TONE : Press to switch the test tone on or off
when listening to a surround mode.
ATT : Press to attenuate (lower) the level of the input
signals and prevent distortion (refer to "Display", 5,
Overload indicator).
SIG.SELECT : When the same component uses both
analog and digital connections, use to select input signals
as digital or analog.
CH.LEVEL (–/+) : Use to adjust individual speaker levels.
EFFECT (+/–) : Use to adjust the DSP mode effect level.
• [TUNER operations (press TUNER first)]
Number buttons (0~9) : During preset tuning, use to
input the number of the preset station. Use to input the
station frequency during direct tuning.
CLASS (+10) : Press repeatedly to switch the preset
station classes during preset tuning.
MENU : Press to activate direct tuning.
8 FUNCTION button
Press repeatedly to select a source.
9 MODE CHECK button
Press to confirm the current remote operation mode and
to switch operation modes without changing the source .
0 Power button
Press to turn on or put in standby all connected
components other than this unit.
- TV/TV FUNC button
Press TV to turn the TV's power on or put in standby.
Press TV FUNC to select the TV for remote control
operation.
= RECEIVER button
Press to select the receiver for remote control operation.
~ FL DIMMER button
Press to adjust the brightness of the fluorescent display.
Four levels of brightness ranging from very dim to very
bright can be selected.
! COMMANDER SET UP button
Use to customize the remote control functions.
@ DIRECT button
Use to playback original source audio. When DIRECT is
ON, Dolby, DSP, LOUDNESS, DIGITAL NR and
MIDNIGHT mode are automatically turned OFF.