Operating Jvc's Audio/Video Components - JVC RX-888RBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 39) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source. To
operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 12.)
• Refer also to the manuals supplied with your components.
TV/CATV/DBS VCR 1
DVD DVD MUILTI CD TAPE/MD
TV/DBS VIDEO PHONO FM/AM
VCR 1 VCR 2 ANALOG/DIGITAL SLEEP
SURROUND CNTR TONE CNTR
1 2 3
ON/OFF
MENU MENU
SURROUND TEST REAR-L
4 5 6
MODE
ENTER ENTER
DISC EFFECT REAR-R
7 8 9
/P
SOUND SEA MODE SUBWOOFER
10 0 +10
100+
RETURN FM MODE/MUTING
AUDIO/
TV/VCR
MENU
CATV/DBS
SET
TEXT
EXIT
DISPLAY
TV VOL CHANNEL VOLUME
TV/VIDEO VCR 1 TAPE MUTING
CONTROL
/REW PLAY FF/
PTY PTY SEARCH PTY
REC STOP PAUSE
DISPLAY MODE
RM-SRX888R REMOTE CONTROL
Tuner
After pressing FM/AM (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations:
FM/AM: Alternates between FM and AM (MW/LW).
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
FM MODE/MUTING: Changes the FM reception mode.
PTY SEARCH:
Searches for a program by PTY codes.
PTY – / +: Selects the PTY codes.
DISPLAY MODE: Shows the RDS signals.
45
AUDIO/
TV/VCR
CATV/DBS
Check to see if its remote
control mode selector is set
to the correct position.
To operate the audio
system, TVs, and VCRs,
set it to "AUDIO/TV/VCR."
Sound control section (Amplifier)
You can always perform the following operations (with the remote
control mode selector set to "AUDIO/TV/VCR"):
SURROUND ON/OFF: Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, DTS
Digital Surround, and MPEG
Multichannel.
SURROUND MODE: Selects the DSP modes.
After pressing SOUND (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations:
SEA MODE: Changes the SEA modes.
SUBWOOFER – / +: Adjusts the subwoofer output level.
CNTR – / +:
Adjusts the center speaker output level.
REAR•L – / +:
Adjusts the left rear speaker output level.
REAR•R – / +: Adjusts the right rear speaker output level.
EFFECT:
Selects the effect level.
TEST:
Turns on or off the test tone output.
CNTR TONE: Selects the center tone.
Note:
After adjusting sounds, press the corresponding source selecting
button or DISC to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
CD player
After pressing CD (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on
the CD player:
PLAY:
Starts playing.
4 : 4 4
4 4
Returns to the beginning of the current (or
previous) track.
¢ : ¢ ¢ ¢ ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD player-changer
After pressing DISC (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on a
CD player-changer:
PLAY:
Starts playing.
4 4 : 4
4 4
Returns to the beginning of the current (or previous)
track.
¢ ¢ ¢ ¢ : ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 – 6, 7/P:
Selects the number of a disc installed in a CD
player-changer.
After pressing CD (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on
the CD player-changer:
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.