Sony DCR-TRV240 Service Manual page 144

3. Switching Position Adjustment (VC-276 board)
To obtain normal playback waveform output during the Digital8
playback mode, adjust the switching position.
Mode VTR playback
Signal SW/OL reference tape (WR5-2D)
Measurement Point Display data of page: 3, address: 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 10, 11, 12, 13
Specified Value 00
Note1: The data of page: 0, address: 10 must be "00".
Adjusting method:
Order Page Address Data
1
2 0 01 01
3 C 10 EE
4 3 21
5 3 01 0D
6 3 02
7 3 03
8 C 10
9 0 01 00
Note2: If the data of page: 3, address: 21 is "72", the tape top being played.
After playing the tape for 1 to 2 seconds, stop it, perform step 5
and higher.
Note3: If the data is other value, adjustment has errors. If bit 0 of the data
is "1", the A channel is defective. If bit 1 is "1", the B channel is
defective. Contents of the defect is written into page: C, addresses:
10 and 12. See the following table. (For the bit values, refer to "5-
4. SERVICE MODE", "4-3. 3. Bit value discrimination". ) If bit 3
of the data is "1",the tape end being played, and adjustment has
errors.
Note4: If the data is "EE", rewind the tape and repeat steps 1 to 7.
When the A channel is defective
Data of page: C, Contents of defect
address: 10
EE Writing into EEPROM (IC4502) is
defective
E8 Adjustment data is out of range
E7 No data is returned from IC3301
When the B channel is defective
Data of page: C, Contents of defect
address: 12
E8 Adjustment data is out of range
E7 No data is returned from IC3301
RadarW RadarW RadarW
Procedure
Insert the SW/OL reference tape
and enter the VTR STOP mode.
Set the data.
Set the data, and press PAUSE
button.
Check that the data is "02".
(Note2)
Set the data, and press PAUSE
button.
Check that the data changes to
"00" in the following order.
"0E"→"29"→"0E"→"20"→"00"
Check that the data is "00".
(Note3)
Check that the data is other than
"EE". (Note4)
Set the data.
4. AGC Center Level and APC & AEQ Adjustment
Note: The data of page: 0, address: 10 must be "00".
Use a Hi8 MP tape.
4-1. Preparations before adjustments
Mode
Subject
Adjusting method:
Order Page Address Data
1 0 01
2 8 21
3
4-2. AGC Center Level Adjustment (VC-276 board)
RadarW RadarW RadarW
Mode
Signal
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note 1: Connect a 75Ω resistor between Pin qh and Pin w; (GND) of
CN1108.
75Ω resistor (Parts code: 1-247-804-11)
Adjusting method:
Order Page Address Data
1
2 0 01
3 <2> <4D> <40> Set the data. (Note2)
[7] [62]
4 3 33
5
6 3 01
7 3 02
8 3 03
9
Note 2: < >: DCR-TRV240, [ ]: DCR-TRV340
Note 3: If the data of page: 3, address: 03 is other than "00", adjustment
has errors.
5-43
DCR-TRV240/TRV340
Camera recording
Arbitrary
Procedure
01 Set the data.
C8 Set the data.
Record the camera signal for three
minutes.
Playback
Recorded signal at "Preparations before
adjustments"
Pin qh of CN1108 (RF MON) (Note 1)
Ext. trigger: Pin qd of CN1108 (RF
SWP)
Oscilloscope
C
1E
The data of page: 3, address: 03 is "00"
Procedure
Playback the recorded signal at
"Preparations before adjustments"
01 Set the data.
[01]
08 Set the data.
Confirm that the playback RF
signal is stable. (Fig. 5-3-4.)
23 Set the data, and press PAUSE
button.
Check that the data is "00".
Check that the data is "00".
(Note3)
Perform "APC & AEQ Adjustment".