Other Viewing Options; Presetting Remote Control Function; Operating The Connected Equipment - Sharp Aquas LC-52LE920UN Operation Manual

Other Viewing Options
Presetting Remote Control Function
Operating the Connected Equipment
11 FLASHBACK
• Press to switch between the current channel and the
channel you were watching immediately before. Some
manufacturers do not preset FLASHBACK. (STB)
12 CH/\lV
• Press
CH/\
or
CHV
to tune in to a higher or lower
channel. (STB)
• Press to select the channel of the TV tuner on the VCR.
(VCR)
13 MENU
• When this button is pressed, the OVO/BO menu will
display. (OVO, BO)
14 ./T/ /~,ENTER
• /;",/T I
/~:
Press the button to select items on the STB
GUIDE screen or STB MENU screen. (STB)
Press the button to select items on the OVO/BO menu
screen. (OVO, BO)
• ENTER: Press to activate the selected function. (STB,
OVO, BO)
1 POWER (SOURCE)
• Turns the connected equipment power on and off.
2~
• Starts playback. (VCR, OVO, BO)
3 ........
• Rewinds the tape and allows picture search. (VCR)
• Hold down to go in reverse. (OVO, BO)
4 .
• Stops the tape transport. (VCR)
• Playback stops when pressed. With some OVO/Blu-ray
disc players, pressing the button twice may open the disc
tray. (OVO, BO)
5H~
• Pressing quickly once takes you to the start of the chapter
currently playing. Each time you press it, you move back
to the start of the previous chapter. (OVO, BO)
6 0-9, •
(DOT) (STB)
• Press a button (or buttons) that corresponds to the
channel that you wish to watch.
7~~
• Rapidly advances the tape and allows picture search.
(VCR)
• Hold down to fast forward. (OVO, BO)
811
• Sets pauses and still pictures. (VCR, OVO, BO)
9~
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead to the
start of the next chapter. (OVO, BO)
10 eREC
• Starts recording. (VCR)
To operate the connected equipment, press STB,
DVD·VCR or AUDIO to select your device. (STB
(cable/satellite set-top box), OVO, BO, VCR or AUDIO.)
The remote control unit button will function as follows.
• When you operate VCR, OVO or BO, press INPUT to select
the terminal connected to your device.
• CABLE and SAT cannot be selected at the same time.
INPUT
III
~-;.;--11
~-=::""";':---7
::--~II:---
12
r-----;::::===~~- 13
TV
2
---.;;...-=::....=;
6-~
POWER
B
AQUaS
1.1
NET
'lIl
APPS
:.O~ETURN~14
o
0
Presetting manufacturer codes
1
Press an appropriate button (STB, DVD·VCR or
AUDIO) to operate the connected equipment.
2
Press an appropriate button (STB, DVD·VCR or
AUDIO) and DISPLAY at the same time to enter
the code registration mode.
3
Press 0-9 to enter the manufacturer code. (See
page 45.)
• Preset mode is finished once the LED no longer lights
up.
4
After registering the code, the LED will stop blinking
then turn off after one second. (If you perform an
incorrect operation, the LED will blink quickly then
turn off.)
You can operate the connected AV products (AV
receiver, cable box, SAT tuner, OTV, VCR, OVO, BO,
LO) using the presetting manufacturer function of your
remote control unit.
@-
44