Fm Lcut Freq; Fm Lcut Slope; Fm Hcut Freq; Data Hcut Slope - Yaesu FT DX 3000 Operating Manual

075 DATA IN SELECT
Function: Selects the input data to be used in the DATA
mode.
Available Values: DATA/USB
Default Setting: DATA
Selects the input data to be used in the DATA mode.
DATA: Inputs the transmission data from the DATA IN
(pin 1) terminal of the PACKET Jack on the rear panel
while using the DATA mode.
USB: Inputs the transmission data from the USB Jack
on the rear panel while using the DATA mode.
076 DATA MIC GAIN
Function: Sets the data input level from the TNC to the
AFSK modulator.
Available Values: MCVR/0 ~ 100
Default Setting: MCVR
When this menu is set to "MCVR", you may adjust the
microphone gain using the front panel [MIC/SPEED]
knob.
077 DATA OUT LEVEL
Function: Sets the AFSK data output level at the output
port (pin 5) of the RTTY/PKT jack.
Available Values: 0 ~ 100
Default Setting: 50
078 DATA VOX GAIN
Function: Adjusts the "VOX" Gain in the DATA mode.
Available Values: 0 ~ 100
Default Setting: 50
079 DATA VOX DELEY
Function: Adjusts the "VOX" Delay (receiver recovery)
time in the DATA mode.
Available Values: 30 ~ 3000 msec (10 msec/step)
Default Setting: 300 msec
FT 3000 O
DX peraTing
M
anual
M
MODE-FM Group

080 FM LCUT FREQ

Function: Selects the cutoff frequency of the lower side
of the RX audio filter in the FM mode.
Available Values: OFF/100 ~ 1000 Hz (50 Hz/step)
Default Setting: 250

081 FM LCUT SLOPE

Function: Selects the filter slope of the lower side of the
RX audio filter in the FM mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct

082 FM HCUT FREQ

Function: Selects the cutoff frequency of the upper side
of the RX audio filter in the FM mode.
Available Values: OFF/700 ~ 4000 Hz (50 Hz/step)
Default Setting: OFF

083 DATA HCUT SLOPE

Function: Selects the filter slope of the upper side of the
RX audio filter in the FM mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
084 FM MIC GAIN
Function: Sets the microphone gain for the FM mode.
Available Values: MCVR/0 ~ 100
Default Setting: MCVR
When this menu is set to "MCVR", you may adjust the
microphone gain using the front panel [MIC/SPEED]
knob.
085 FM MIC SEL
Function: Selects the microphone to be used on the FM
mode.
Available Values: FRONT / DATA / USB
Default Setting: FRONT
FRONT: Selects the microphone connected to the front
panel MIC jack while using the FM mode.
DATA: Selects the microphone connected to pin 1 of
the PACKET Jack while using the FM mode.
USB: Selects the microphone connected to the USB
Jack while using the FM mode.
086 RPT SHIFT (28MHz)
Function: Sets the magnitude of the repeater shift on the
28 MHz band.
Available Values: 0 ~ 1000 kHz (50 kHz/step)
Default Setting: 100 kHz
087 RPT SHIFT (50MHz)
Function: Sets the magnitude of the repeater shift on the
50 MHz band.
Available Values: 0 ~ 4000 kHz (10 kHz/step)
Default Setting: 1000 kHz
M
enu ODe
Page 119