GE NetworX NX-4V2 Installation And Startup page 24

5 = On if Zone Type can be bypassed.
6 = On if Zone Type is included in the group shunt.
7 = On if Zone Type is force armable.
8 = On if Zone Type is entry guard.
Segment 3:
1- On enables Fast Loop Response. (50mS)- Off= 500mS
2- On enables Double End Of Line Tamper zone. (Mainly used for tamper on wireless zones)
3- On enables Trouble Reporting zone. (Day zone and Fire zones)
4- On if Zone Type is a Cross Zone.
5- On enables Dialer Delay zone. (See location 40, page 19)
6- On if Zone Type will swinger shutdown. (See location 38, page 18)
7- On enables Restore reporting.
8- On enables Listen-In. (See location 40, page 19)
Segment 4:
1 = On enables Zone Activity Monitor. (See location 40, page 19)
2 = On enables End of Line Resistor Defeat on Non-Fire/Non-Keyswitch zones.
3 = On enables zone to act as request to exit input / disables for alarm activation.
4 = On enables zone to act as access entry point (Refer to NX-1700E card reader instruction manual. Do not enable this segment
unless configured with Access Control.)
5-8 = Reserved.
Segment 5: Reserved.
112
Location 112 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
113
Use "Zone Type Characteristic Selections" described in Location 111, page 23
114
Location 114 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
115
Use "Zone Type Characteristic Selections" described in Location 111, page 23
116
Location 116 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
117
Use "Zone Type Characteristic Selections" described in Location 111, page 23
118
Location 118 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
119
Use "Zone Type Characteristic Selections" described in Location 111, page 23
120
Location 120 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
121
Use "Zone Type Characteristic Selections" described in Location 111, page 23
122
Location 122 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen from the list on
page 39. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location 110 on page 23 for details.
123
Use "Zone Type Characteristic Selections" described in Location 111, page 23
24
ZONE TYPE 2 ALARM EVENT CODE
ZONE TYPE 2 CHARACTERISTIC SELECT
ZONE TYPE 3 ALARM EVENT CODE
ZONE TYPE 3 CHARACTERISTIC SELECT
ZONE TYPE 4 ALARM EVENT CODE
ZONE TYPE 4 CHARACTERISTIC SELECT
ZONE TYPE 5 ALARM EVENT CODE
ZONE TYPE 5 CHARACTERISTIC SELECT
ZONE TYPE 6 ALARM EVENT CODE
ZONE TYPE 6 CHARACTERISTIC SELECT
ZONE TYPE 7 ALARM EVENT CODE
ZONE TYPE 7 CHARACTERISTIC SELECT
WWW.DIYALARMFORUM.COM
1 ............ numerical
5 ............ feature select
1 ............ numerical
5 ............ feature select
1 ............ numerical
5 ............ feature select
1 ............ numerical
5 ............ feature select
1 ............ numerical
5 ............ feature select
1 ............ numerical
5 ............ feature select
NX-4V2 Control